tty/serial/8250: use mctrl_gpio helpers
This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.
Changed by Stefan:
Only call mctrl_gpio_init(), if the device has no ACPI companion device
to not break existing ACPI based systems. Also only use the mctrl_gpio_
functions when "gpios" is available.
Use MSR / MCR <-> TIOCM wrapper functions.
Signed-off-by: Yegor Yefremov <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
Reviewed-by: Mika Westerberg <[email protected]>
Tested-by: Yegor Yefremov <[email protected]>
Cc: Mika Westerberg <[email protected]>
Cc: Andy Shevchenko <[email protected]>
Cc: Giulio Benetti <[email protected]>
Cc: Yegor Yefremov <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt
index 3cba12f..20d351f 100644
--- a/Documentation/devicetree/bindings/serial/8250.txt
+++ b/Documentation/devicetree/bindings/serial/8250.txt
@@ -53,6 +53,9 @@
programmable TX FIFO thresholds.
- resets : phandle + reset specifier pairs
- overrun-throttle-ms : how long to pause uart rx when input overrun is encountered.
+- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD
+ line respectively. It will use specified GPIO instead of the peripheral
+ function pin for the UART feature. If unsure, don't specify this property.
Note:
* fsl,ns16550:
@@ -74,3 +77,19 @@
interrupts = <10>;
reg-shift = <2>;
};
+
+Example for OMAP UART using GPIO-based modem control signals:
+
+ uart4: serial@49042000 {
+ compatible = "ti,omap3-uart";
+ reg = <0x49042000 0x400>;
+ interrupts = <80>;
+ ti,hwmods = "uart4";
+ clock-frequency = <48000000>;
+ cts-gpios = <&gpio3 5 GPIO_ACTIVE_LOW>;
+ rts-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
+ dtr-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+ dsr-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ dcd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ rng-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index 57db8c1..33ad9d6d 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -11,6 +11,8 @@
#include <linux/serial_reg.h>
#include <linux/dmaengine.h>
+#include "../serial_mctrl_gpio.h"
+
struct uart_8250_dma {
int (*tx_dma)(struct uart_8250_port *p);
int (*rx_dma)(struct uart_8250_port *p);
@@ -214,11 +216,25 @@ static inline int serial8250_MSR_to_TIOCM(int msr)
static inline void serial8250_out_MCR(struct uart_8250_port *up, int value)
{
serial_out(up, UART_MCR, value);
+
+ if (up->gpios)
+ mctrl_gpio_set(up->gpios, serial8250_MCR_to_TIOCM(value));
}
static inline int serial8250_in_MCR(struct uart_8250_port *up)
{
- return serial_in(up, UART_MCR);
+ int mctrl;
+
+ mctrl = serial_in(up, UART_MCR);
+
+ if (up->gpios) {
+ unsigned int mctrl_gpio = 0;
+
+ mctrl_gpio = mctrl_gpio_get_outputs(up->gpios, &mctrl_gpio);
+ mctrl |= serial8250_TIOCM_to_MCR(mctrl_gpio);
+ }
+
+ return mctrl;
}
#if defined(__alpha__) && !defined(CONFIG_PCI)
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index e441221..a447077 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -14,6 +14,7 @@
* serial8250_register_8250_port() ports
*/
+#include <linux/acpi.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/ioport.h>
@@ -982,6 +983,8 @@ int serial8250_register_8250_port(struct uart_8250_port *up)
uart = serial8250_find_match_or_unused(&up->port);
if (uart && uart->port.type != PORT_8250_CIR) {
+ struct mctrl_gpios *gpios;
+
if (uart->port.dev)
uart_remove_one_port(&serial8250_reg, &uart->port);
@@ -1016,6 +1019,20 @@ int serial8250_register_8250_port(struct uart_8250_port *up)
if (up->port.flags & UPF_FIXED_TYPE)
uart->port.type = up->port.type;
+ /*
+ * Only call mctrl_gpio_init(), if the device has no ACPI
+ * companion device
+ */
+ if (!has_acpi_companion(uart->port.dev)) {
+ gpios = mctrl_gpio_init(&uart->port, 0);
+ if (IS_ERR(gpios)) {
+ if (PTR_ERR(gpios) != -ENOSYS)
+ return PTR_ERR(gpios);
+ } else {
+ uart->gpios = gpios;
+ }
+ }
+
serial8250_set_defaults(uart);
/* Possibly override default I/O functions. */
diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
index ed25cfc..3ef65cb 100644
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -141,18 +141,20 @@ static void omap8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
serial8250_do_set_mctrl(port, mctrl);
- /*
- * Turn off autoRTS if RTS is lowered and restore autoRTS setting
- * if RTS is raised
- */
- lcr = serial_in(up, UART_LCR);
- serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- if ((mctrl & TIOCM_RTS) && (port->status & UPSTAT_AUTORTS))
- priv->efr |= UART_EFR_RTS;
- else
- priv->efr &= ~UART_EFR_RTS;
- serial_out(up, UART_EFR, priv->efr);
- serial_out(up, UART_LCR, lcr);
+ if (!up->gpios) {
+ /*
+ * Turn off autoRTS if RTS is lowered and restore autoRTS
+ * setting if RTS is raised
+ */
+ lcr = serial_in(up, UART_LCR);
+ serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
+ if ((mctrl & TIOCM_RTS) && (port->status & UPSTAT_AUTORTS))
+ priv->efr |= UART_EFR_RTS;
+ else
+ priv->efr &= ~UART_EFR_RTS;
+ serial_out(up, UART_EFR, priv->efr);
+ serial_out(up, UART_LCR, lcr);
+ }
}
/*
@@ -453,7 +455,8 @@ static void omap_8250_set_termios(struct uart_port *port,
priv->efr = 0;
up->port.status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS | UPSTAT_AUTOXOFF);
- if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW) {
+ if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW &&
+ !up->gpios) {
/* Enable AUTOCTS (autoRTS is enabled when RTS is raised) */
up->port.status |= UPSTAT_AUTOCTS | UPSTAT_AUTORTS;
priv->efr |= UART_EFR_CTS;
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 74d81f1..a6fabc7 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1656,6 +1656,8 @@ static void serial8250_disable_ms(struct uart_port *port)
if (up->bugs & UART_BUG_NOMSR)
return;
+ mctrl_gpio_disable_ms(up->gpios);
+
up->ier &= ~UART_IER_MSI;
serial_port_out(port, UART_IER, up->ier);
}
@@ -1668,6 +1670,8 @@ static void serial8250_enable_ms(struct uart_port *port)
if (up->bugs & UART_BUG_NOMSR)
return;
+ mctrl_gpio_enable_ms(up->gpios);
+
up->ier |= UART_IER_MSI;
serial8250_rpm_get(up);
@@ -1939,12 +1943,17 @@ unsigned int serial8250_do_get_mctrl(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
unsigned int status;
+ unsigned int val;
serial8250_rpm_get(up);
status = serial8250_modem_status(up);
serial8250_rpm_put(up);
- return serial8250_MSR_to_TIOCM(status);
+ val = serial8250_MSR_to_TIOCM(status);
+ if (up->gpios)
+ return mctrl_gpio_get(up->gpios, &val);
+
+ return val;
}
EXPORT_SYMBOL_GPL(serial8250_do_get_mctrl);
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index 296115f..509f6a3 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -8,6 +8,7 @@
tristate "8250/16550 and compatible serial support"
depends on !S390
select SERIAL_CORE
+ select SERIAL_MCTRL_GPIO if GPIOLIB
---help---
This selects whether you want to include the driver for the standard
serial ports. The standard answer is Y. People who might say N
diff --git a/include/linux/serial_8250.h b/include/linux/serial_8250.h
index 5e0b594..bb2bc99 100644
--- a/include/linux/serial_8250.h
+++ b/include/linux/serial_8250.h
@@ -110,6 +110,7 @@ struct uart_8250_port {
* if no_console_suspend
*/
unsigned char probe;
+ struct mctrl_gpios *gpios;
#define UART_PROBE_RSA (1 << 0)
/*
