What:		/sys/class/power_supply/wireless/device/version
Contact:	pixel-bms-sw@google.com
Description:
		Version information about the chip and driver such as chip id, firmware
		version date and time codes in human readable format

What:		/sys/class/power_supply/wireless/device/status
Contact:	pixel-bms-sw@google.com
Description:
		Driver status and state information printed in human readable format

What:		/sys/class/power_supply/wireless/device/addr
Contact:	pixel-bms-sw@google.com
Description:
		i2c 16-bit register address input to send manual i2c commands

What:		/sys/class/power_supply/wireless/device/count
Contact:	pixel-bms-sw@google.com
Description:
		i2c count input to send manual i2c commands in number of bytes to read/write

What:		/sys/class/power_supply/wireless/device/data
Contact:	pixel-bms-sw@google.com
Description:
		i2c data information to send manual i2c commands in 0xAA 0xBB 0xCC format

What:		/sys/class/power_supply/wireless/device/ccreset
Contact:	pixel-bms-sw@google.com
Description:
		Reset the in-band communication channel between RX and TX

What:		/sys/class/power_supply/wireless/device/txbusy
Contact:	pixel-bms-sw@google.com
Description:
		Check if the in-band communication channel is busy transmitting

What:		/sys/class/power_supply/wireless/device/txdone
Contact:	pixel-bms-sw@google.com
Description:
		Check if the transmission over in-band communication channel is done

What:		/sys/class/power_supply/wireless/device/txlen
Contact:	pixel-bms-sw@google.com
Description:
		Number of bytes to transmit in the in-band communication channel

What:		/sys/class/power_supply/wireless/device/rxlen
Contact:	pixel-bms-sw@google.com
Description:
		Number of bytes received in the in-band communication channel

What:		/sys/class/power_supply/wireless/device/rxdone
Contact:	pixel-bms-sw@google.com
Description:
		Whether the in-band communication channel data receiving is complete

What:		/sys/class/power_supply/wireless/device/icl_ramp_ua
Contact:	pixel-bms-sw@google.com
Description:
		Value to ramp the ICL to during BPP

What:		/sys/class/power_supply/wireless/device/icl_ramp_delay_ms
Contact:	pixel-bms-sw@google.com
Description:
		Amount of time to delay betwenn BPP ICL ramp steps in ms

What:		/sys/class/power_supply/wireless/device/force_epp
Contact:	pixel-bms-sw@google.com
Description:
		Always have the driver act as if the device is in EPP even if it isn't

What:		/sys/class/power_supply/wireless/device/dc_icl_bpp
Contact:	pixel-bms-sw@google.com
Description:
		Set the DC_ICL in BPP mode

What:		/sys/class/power_supply/wireless/device/dc_icl_epp
Contact:	pixel-bms-sw@google.com
Description:
		Set the DC_ICL in EPP mode

What:		/sys/class/power_supply/wireless/device/alignment
Contact:	pixel-bms-sw@google.com
Description:
		Show the alignment status

What:		/sys/class/power_supply/wireless/device/aicl_delay_ms
Contact:	pixel-bms-sw@google.com
Description:
		Legacy interface for setting AICL_DELAY power supply property for QC compat

What:		/sys/class/power_supply/wireless/device/aicl_icl_ua
Contact:	pixel-bms-sw@google.com
Description:
		Legacy interface for setting AICL_ICL power supply property for QC compat

What:		/sys/class/power_supply/wireless/device/operating_freq
Contact:	pixel-bms-sw@google.com
Description:
		Show the current operating frequency of the WLC

What:		/sys/class/power_supply/wireless/device/ptmc_id
Contact:	pixel-bms-sw@google.com
Description:
		Show the TX ID as received through Bidi (proprietary)

What:		/sys/class/power_supply/wireless/device/ext_ben
Contact:	pixel-bms-sw@google.com
Description:
		External boost on or off

What:		/sys/class/power_supply/wireless/device/qi_vbus_en
Contact:	pixel-bms-sw@google.com
Description:
		QI_VBUS_EN gpio on or off

What:		/sys/class/power_supply/wireless/device/has_wlc_dc
Contact:	pixel-bms-sw@google.com
Description:
		Enable or disable HPP feature

What:		/sys/class/power_supply/wireless/device/gpp_enhanced
Contact:	pixel-bms-sw@google.com
Description:
		Enable or disable GPP15W feature

What:		/sys/class/power_supply/wireless/device/authstart
Contact:	pixel-bms-sw@google.com
Description:
		Start WPC Authentication sequence

What:		/sys/class/power_supply/wireless/device/log_current_filtered
Contact:	pixel-bms-sw@google.com
Description:
		Enable printing WLC current continuously into the log

What:		/sys/class/power_supply/wireless/device/charge_stats
Contact:	pixel-bms-sw@google.com
Description:
		Dump out and clear charge stats from the last charging session

What:		/sys/class/power_supply/wireless/device/fw_rev
Contact:	pixel-bms-sw@google.com
Description:
		Saved FW version from the last WLC power on

What:		/sys/class/power_supply/wireless/device/authtype
Contact:	pixel-bms-sw@google.com
Description:
		Authentication type to run (0 = Bidi, others = WPC packet types)

What:		/sys/class/power_supply/wireless/device/features
Contact:	pixel-bms-sw@google.com
Description:
		Supported feature mask in the format "id:features". id=0 corresponds to just set
		current session

What:		/sys/class/power_supply/wireless/device/mitigate_threshold
Contact:	pixel-bms-sw@google.com
Description:
		SOC threshold at which to trigger dream defend on DL/LL

What:		/sys/class/power_supply/wireless/device/wpc_ready
Contact:	pixel-bms-sw@google.com
Description:
		Check this node to see if the driver/HW is ready for WPC authentication

What:		/sys/class/power_supply/wireless/device/qien
Contact:	pixel-bms-sw@google.com
Description:
		Check/force state of the WLC disable GPIO

What:		/sys/class/power_supply/wireless/device/align_delta
Contact:	pixel-bms-sw@google.com
Description:
		Set the opfreq delta threshold for being considered misaligned

What:		/sys/class/power_supply/wireless/device/ldo_en
Contact:	pixel-bms-sw@google.com
Description:
		Interface for enable/disable external LDO for chips that support it

What:		/sys/class/power_supply/wireless/device/rtx_sw
Contact:	pixel-bms-sw@google.com
Description:
		Change/check the RTX switch status

What:		/sys/class/power_supply/wireless/device/rtx_boost
Contact:	pixel-bms-sw@google.com
Description:
		Turn on the RTX boost to power on the WLC chip. For debug and FW update

What:		/sys/class/power_supply/wireless/device/rtx
Contact:	pixel-bms-sw@google.com
Description:
		Turn on RTX

What:		/sys/class/power_supply/wireless/device/rtx_status
Contact:	pixel-bms-sw@google.com
Description:
		Read the status of RTX

What:		/sys/class/power_supply/wireless/device/is_rtx_connected
Contact:	pixel-bms-sw@google.com
Description:
		Check if RTX is connected

What:		/sys/class/power_supply/wireless/device/rx_lvl
Contact:	pixel-bms-sw@google.com
Description:
		Check the battery level of the device being charged in RTX

What:		/sys/class/power_supply/wireless/device/rtx_err
Contact:	pixel-bms-sw@google.com
Description:
		Read the current RTX error

What:		/sys/class/power_supply/wireless/device/txdata
Contact:	pixel-bms-sw@google.com
Description:
		Set data to be sent over in-band wireless communication

What:		/sys/class/power_supply/wireless/device/rxdata
Contact:	pixel-bms-sw@google.com
Description:
		Read data from in-band wireless communication