###############################################################################
#Board Varaints and Versions are defined below:
#BOARD_VARIANT_NXPREF    0x01
#BOARD_NXPREF_VERSIONS(0x01, 0x02)

#BOARD_VARIANT_CUSTREF1  0x2A
#BOARD_CUSTREF1_VERSIONS(0x01,0x02,0x03)

UWB_BOARD_VARIANT_CONFIG=0x01
UWB_BOARD_VARIANT_VERSION=0x01

###############################################################################
#                          Extended CofigID
#DELAY_CALIBRATION_VALUE    E400
#AOA_CALIBRATION_CTRL       E401
#DPD_WAKEUP_SRC             E402
#DPD_ENTRY_TIMEOUT          E404
#GPIO_USAGE_CONFIG          E408
  ##Note: Configure the GPIO for multiple purposes depending on usecase ID
  ##      config(E4, 08, 03, 00, 00, 00)
  ##      Length and number of parameter accordingly in the header part.
#CLK_CONFIG_CTRL            E430
  ##Note: Config for clock source selection and refer UCI specification
  ##      for more information.
# Refer the NXP UCI specification for below configs
#ANTENNA_RX_IDX_DEFINE   E460
#ANTENNA_TX_IDX_DEFINE   E461
#ANTENNAS_CONFIGURATION_RX E465

UWB_CORE_EXT_DEVICE_DEFAULT_CONFIG={05,
    E4, 03, 01, b4,
    E4, 04, 02, f4, 01,
    E4, 60, 07, 01, 01, 02, 01, 00, 01, 00,
    E4, 61, 06, 01, 01, 01, 00, 00, 00,
    E4, 65, 06, 01, 03, 03, 00, 01, 01
}

# This config enable/disable the dpd entry prevention ntf config during init
# 00 for disable
# 01 for enable
UWB_DPD_ENTRY_PREVENTION_NTF_CONFIG=0x01

#This config call's suspend to kernel driver on idle
#This is only activated when AUTO_SUSPEND_ENABLED=1
#0=disable
#1=enable
AUTO_SUSPEND_ENABLE=0
#This config defines duration to resume the device before sending any commands
AUTO_SUSPEND_TIMEOUT_MS=100

##Note: Below configs are applicable in User_Mode FW only
#WIFI_COEX_FEATURE_ALL_CH  0xF0
##Note: WIFI_COEX_FEATURE_ALL_CH is disabled by default.
  ##  Octet[0]: Enable/Disable WiFi CoEx feature
  ##  0x00: Disable (default)
  ##  • b[3:0]: Enable/Disable functionality CoEx
  ##  – 0x1 : Enable CoEx Interface without Debug and without Warning Verbose
  ##  – 0x2 : Enable CoEx Interface with Debug Verbose only
  ##  – 0x3 : Enable CoEx Interface with Warnings Verbose only
  ##  – 0x4 : Enable CoEx Interface with both Debug and Warning Verbose
  ##  • b[7:4]: CoEx Interface (GPIO) selection:
  ##  – 0x0 : GPIO Interface
  ##  – Rest of the values are Reserved
  ##  Octect[1]: Number of channels N Shall be >= 1 (0 will be rejected by UWBS)
  ##  N*4 octets to follow
  ##  Octet[2]: Channel ID
  ##  Octet[3]: MIN_GUARD_DURATION
  ##  Octet[4]: MAX_GRANT_DURATION
  ##  Octet[5]: ADVANCED GRANT DURATION
  ##  Based on requirement add the below configs:
  ##  Enable CH5 - (F0, 06, 01, 01, 05, 3C, 1E, 1E)
  ##  Enable CH9 - (F0, 06, 01, 01, 09, 3C, 1E, 1E)
  ##  Enable both CH5 and CH9 - (F0, 0A, 01, 02, 05, 3C, 1E, 1E, 09, 3C, 1E, 1E)
  ##
  ##  Update the length and number of parameter accordingly in
  ##  the header part.
  ##  WIFI COEX feature supports only in user binary.
#GPIO_USAGE_CONFIG E4 08
  ## Customer need to set the DPD_WAKEUP_SOURCE as 02 (GPIO1) before applying
  ## the GPIO_USAGE_CONFIG command to enable time sync notification feature
UWB_USER_FW_BOOT_MODE_CONFIG={20, 04, 00, 13, 02,
    F0, 06, 00, 01, 05, 3C, 1E, 1E,
    E4, 02, 01, 00,
    E4, 08, 03, 00, 00, 00
}

# Set system time uncertainty value in microsec for CCC ranging
UWB_INITIATION_TIME_DELTA=200000

#LIST OF UWB CAPABILITY INFO NOT RECEIVED FROM UWBS
# mapping device caps according to Fira 2.0
# TODO: Remove once FW support available
UWB_VENDOR_CAPABILITY={A8, 04, 05, 00, 00, 00,
  E3, 01, 01,
  E4, 04, 64, 00, 00, 00,
  E5, 04, 03, 00, 00, 00,
  E6, 01, 01,
  E7, 01, 01,
  E8, 04, B0, 04, 00, 00,
  E9, 04, 05, 00, 00, 00,
  EA, 02, 09, 00,
  AB, 02, 64, 00,
  EB, 04, 05, 00, 00, 00
}

###############################################################################
# Helios PROD Mode FW version
# Make sure you push the Production FW while using this Macro
NXP_UWB_PROD_FW_FILENAME="libsr100t_prod_fw.bin"

# Helios Dev Mode FW version
# Make sure you push the Dev Mode FW while using this Macro
NXP_UWB_DEV_FW_FILENAME="libsr100t_dev_fw.bin"
###############################################################################

###############################################################################
#enable or disable fw download logging
UWB_FW_DOWNLOAD_LOG=0x00
###############################################################################

###############################################################################
#enable or disable delete ursk for ccc session
DELETE_URSK_FOR_CCC_SESSION=0x00
###############################################################################

###############################################################################
#enable or disable sts index overriding for ccc session
OVERRIDE_STS_INDEX_FOR_CCC_SESSION=0x01
###############################################################################

###############################################################################
# set Crystal calibration settings
# byte[0] No Of registers
# byte[2-1] 38.4 MHz XTAL CAP1
# byte[4-3] 38.4 MHz XTAL CAP2
# byte[6-5] 38.4 MHz XTAL GM

# NXP_UWB_XTAL_38MHZ_CONFIG={2F, 21, 00, 0A, 05, 01, 07, 03, 0F, 00, 0F, 00, 21, 00}

###############################################################################
# This config enable/disable the Vendor extended notifications
# 00 for disable
# 01 for enable
NXP_UWB_EXTENDED_NTF_CONFIG={20, 04, 00, 05, 01, E4, 33, 01, 01}

###############################################################################
###############################################################################
# Core Device configurations
# Below sections needs to be updated with the correct values for needed core device configurations

#NXP_CORE_CONF_BLK_1={}

#NXP_CORE_CONF_BLK_2={}

#NXP_CORE_CONF_BLK_3={}

#NXP_CORE_CONF_BLK_4={}

#NXP_CORE_CONF_BLK_5={}

#NXP_CORE_CONF_BLK_6={}

#NXP_CORE_CONF_BLK_7={}

#NXP_CORE_CONF_BLK_8={}

#NXP_CORE_CONF_BLK_9={}

#NXP_CORE_CONF_BLK_10={}


NXP_LOG_JNI_LOGLEVEL=0x05
NXP_LOG_UCI_CORE_LOGLEVEL=0x05
NXP_LOG_UCIHAL_LOGLEVEL=0x05
NXP_LOG_FWDNLD_LOGLEVEL=0x05
NXP_LOG_TML_LOGLEVEL=0x05
NXP_LOG_UCIX_LOGLEVEL=0x05
NXP_LOG_UCIR_LOGLEVEL=0x05