WCNSS_qcom_cfg.ini - device/google/taimen - Git at Google

 # This file allows user to override the factory
 # defaults for the WLAN Driver

 #############################################
 # STA related general configurations
 #############################################
 # Assigned MAC Addresses - This will be used until NV items are in place
 # Each byte of MAC address is represented in Hex format as XX
 Intf0MacAddress=000AF58989FF
 Intf1MacAddress=000AF58989FE
 Intf2MacAddress=000AF58989FD
 Intf3MacAddress=000AF58989FC

 #Channel Bonding
 gChannelBondingMode5GHz=1
 gChannelBondingMode24GHz=0

 #Enable Keep alive with non-zero period value
 gStaKeepAlivePeriod=60

 # Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets)
 gVhtMpduLen=2

 # 0 for OLPC 1 for CLPC and SCPC
 gEnableCloseLoop=1

 ImplicitQosIsEnabled=0

 # Enable Tx beamforming in VHT20MHz
 # Valid values are 0,1. If commented out, the default value is 0.
 # 0=disable, 1=enable
 gEnableTxBFin20MHz=1

 #Enable/Disable SU Tx beamformer support.
 gEnableTxSUBeamformer=1

 # 1=enable tx STBC; 0=disable
 gEnableTXSTBC=1

 # 1=enable STBC; 0=disable STBC
 gEnableRXSTBC=1

 # 1=enable rx LDPC; 0=disable
 gEnableRXLDPC=1

 # Flag to allow STA send AddTspec even when ACM is Off
 gAddTSWhenACMIsOff=1

 # RTS threshold
 RTSThreshold=1048576

 # 802.11d support
 g11dSupportEnabled=0


 # Phy Mode (auto, b, g, n, etc)
 # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
 # 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
 # 7 = 11b only 8 = 11ac only.
 gDot11Mode=0

 # Enable Rx handling options
 # Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium)
 # Rx_thread + NAPI = 5
 rx_mode=5

 #Enable VHT on 2.4Ghz
 gEnableVhtFor24GHzBand=1

 # Regulatory Setting; 0=STRICT; 1=CUSTOM
 gRegulatoryChangeCountry=1

 # userspace country code setting shld take priority
 gCountryCodePriority=1

 # Enable/Disable LPASS support
 # 0 to disable, 1 to enable
 gEnableLpassSupport=1

 # Enable(1)/Disable(0) SIFS burst
 gEnableSifsBurst=1

 # Tx Chain Mask for CCK
 gCckChainMaskEnable=1

 # Tx Chain Mask for 1SS
 gTxChainMask1ss=0

 # TPC power
 gSelfGenFrmPwr=3

 gReportMaxLinkSpeed=0

 # Use OEM provisioned MAC address
 enable_mac_provision=1

 ################ NAN feature set start ###################
 # Enable or Disable NAN
 # 1=Enable (default), 0=Disable
 gEnableNanSupport=1
 genable_nan_datapath=1
 gnan_datapath_ndi_channel=6
 ################ NAN feature set end #####################

 gIgnorePeerHTopMode=1
 gIgnorePeerErpInfo=1

 # 802.11n Protection flag
 gEnableApProt=1

 # Fixed Rate
 gFixedRate=0

 # Intra-BSS forward
 gDisableIntraBssFwd=0

 # WMM Enable/Disable
 WmmIsEnabled=0

 # 802.11h support
 g11hSupportEnabled=1

 #Short Guard Interval Enable/disable
 gShortGI20Mhz=1
 gShortGI40Mhz=1

 #Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec
 gWlanAutoShutdown=0

 #Preferred band (both or 2.4 only or 5 only)
 BandCapability=0

 gVhtChannelWidth=2

 # Enable Tx beamforming
 gTxBFEnable=1

 # Set txchainmask and rxchainmask
 # These parameters are used only if gEnable2x2 is 0
 # Valid values are 1,2
 # Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
 # Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
 gSetTxChainmask1x1=1
 gSetRxChainmask1x1=1

 # 2.4GHz Antenna Sharing is not supported
 gForce1x1Exception=0

 #If set to 0, MCC is not allowed.
 gEnableMCCMode=1

 # MCC to SCC Switch mode: 0-Disable 1-Enable 2-Force SCC if same band
 gWlanMccToSccSwitchMode = 0

 # Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k)
 gVhtAmpduLenExponent=7

 # Maximum number of concurrent connections
 gMaxConcurrentActiveSessions=3

 # Radar PRI multiplier
 gDFSradarMappingPriMultiplier=4

 # Enable or Disable Multi-user MIMO
 # 1=Enable (default), 0=Disable
 gEnableMuBformee=1

 # Enable to check FW hash if secure FW feature is enabled. It's for defconfig
 # builds only since it will be ignored in performance/release builds.
 gEnableFWHashCheck=1

 # Enable or Disable MCC Adaptive Scheduler at the FW
 # 1=Enable (default), 0=Disable
 gEnableMCCAdaptiveScheduler=1

 # Disable/Enable GreenAP
 # 0 to disable, 1 to enable, default: 1
 gEnableGreenAp=0

 ################ Datapath feature set Begin ################
 # Bus bandwidth threshold values in terms of number of packets
 gBusBandwidthHighThreshold=2000
 gBusBandwidthMediumThreshold=500
 gBusBandwidthLowThreshold=150

 # Bus bandwidth compute timeout value in ms
 gBusBandwidthComputeInterval=100

 # VHT Tx/Rx MCS values
 # Valid values are 0,1,2. If commented out, the default value is 0.
 # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
 gVhtRxMCS=2
 gVhtTxMCS=2

 # VHT Tx/Rx MCS values for 2x2
 # Valid values are 0,1,2. If commented out, the default value is 0.
 # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
 gEnable2x2=1
 gVhtRxMCS2x2=2
 gVhtTxMCS2x2=2

 #IPA config is a bit mask and following are the configurations.
 #bit0 IPA Enable
 #bit1 IPA PRE Filter enable
 #bit2 IPv6 enable
 #bit3 IPA Resource Manager (RM) enable
 #bit4 IPA Clock scaling enable
 #bit5 IPA uC ENABLE
 #bit6 IPA uC STA ENABLE
 #bit8 IPA Real Time Debugging
 gIPAConfig=0x3d
 gIPADescSize=800

 # Enable/Disable RX full reorder offload
 gReorderOffloadSupported=1

 # Enable CE classification
 # 1 - enable(default)  0 - disable
 gCEClassifyEnable=1

 # Enable(Tx) fastpath for data traffic.
 # 1 - enable(default)  0 - disable
 gEnableFastPath=1

 # This flag enables IP, TCP and UDP checksum offload
 # 1 - enable(default)  0 - disable
 gEnableIpTcpUdpChecksumOffload=1

 # Enable TCP Segmentation Offload
 # 1 - enable  0 - disable
 TSOEnable=1

 # Enable HT MPDU Density
 # 4 for 2 micro sec
 ght_mpdu_density=4

 # Enable flow steering to enable multiple CEs for Rx flows.
 # Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs.
 # Parallel Rx paths.
 # 1 - enable 0 - disable(default)
 gEnableFlowSteering=1

 ce_service_max_yield_time=500
 ce_service_max_rx_ind_flush=1
 maxMSDUsPerRxInd=8

 # Data Stall Debugging feature
 gEnableDataStallDetection=0

 # Dynamic configuration of TCP limit output bytes
 gTcpLimitOutputEnable=0

 ################ Datapath feature set End ################

 #############################################
 # SCAN related configurations
 #############################################
 # Enable/Disable Idle Scan
 gEnableIdleScan=0

 #Enable Scan Results Aging based on timer
 #Timer value is in seconds
 #If Set to 0 it will not enable the feature
 gScanAgingTime=30

 #Enable Scan Results Aging based on number of scans
 gScanResultAgeCount=1

 #Enable thermal mitigation
 gThermalMitigationEnable=0

 #Maximum Channel time in msec
 gMaxMediumTime=6000

 # Scan Timing Parameters
 # gPassiveMaxChannelTime=110
 # gPassiveMinChannelTime=60
 gActiveMaxChannelTime=40
 gActiveMinChannelTime=20

 gPNOScanSupport=1

 # Enable or Disable Extended Scan (GScan)
 # 1=Enable (default), 0=Disable
 gExtScanEnable=1

 #If set will start with active scan after driver load, otherwise will start with
 #passive scan to find out the domain
 gEnableBypass11d=1

 #If set to 0, will not scan DFS channels
 gEnableDFSChnlScan=1

 #Maxium Channel time in msec
 gMaxMediumTime = 6000

 adaptive_dwell_mode_enabled=1

 hostscan_adaptive_dwell_mode=1

 adapt_dwell_lpf_weight=80

 adapt_dwell_wifi_act_threshold=10

 # Enable or disable Probe Req Information Element whitelist. When enabled, IEs corresponding to bits
 # set in bitmaps are allowed in probe request, all others removed while device is unassociated
 # with an AP
 # 1=Enable, 0=Disable (default)
 g_enable_probereq_whitelist_ies=1

 # ie bitmap examples: <bitmap_name>=<value> [<Allowed Information elements>]
 #    g_probe_req_ie_bitmap_0=0x80000009 #[0, 3, 31]
 #    g_probe_req_ie_bitmap_0=0x00000000 #[] (default)
 #    g_probe_req_ie_bitmap_1=0x80000009 #[32, 35, 63]
 g_probe_req_ie_bitmap_0=0x0000000B
 g_probe_req_ie_bitmap_1=0x00040000
 # g_probe_req_ie_bitmap_2=0x00000000
 # g_probe_req_ie_bitmap_3=0x00000000
 # g_probe_req_ie_bitmap_4=0x00000000
 # g_probe_req_ie_bitmap_5=0x00000000
 g_probe_req_ie_bitmap_6=0x20000000
 # g_probe_req_ie_bitmap_7=0x00000000

 gProbeReqOUIs=0050F208

 #############################################
 # Power related configurations
 #############################################
 # Enable IMPS or not
 gEnableImps=1

 # Enable BMPS or not
 gEnableBmps=1

 # Increase sleep duration (seconds) during IMPS
 # 0 implies no periodic wake up from IMPS. Periodic wakeup is
 # unnecessary if Idle Scan is disabled.
 gImpsModSleepTime=0

 # UAPSD service interval for VO,VI, BE, BK traffic
 InfraUapsdVoSrvIntv=0
 InfraUapsdViSrvIntv=0
 InfraUapsdBeSrvIntv=0
 InfraUapsdBkSrvIntv=0

 # Enable suspend or not
 # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
 gEnableSuspend=3

 #Enable Power Save offload
 gEnablePowerSaveOffload=2

 #Enable Power saving mechanism Based on Android Framework
 #If set to 0 Driver internally control the Power saving mechanism
 #If set to 1 Android Framwrok control the Power saving mechanism
 isAndroidPsEn=0

 beaconEarlyTerminationWakeInterval=3

 #Data Inactivity Timeout when in powersave (in ms)
 gDataInactivityTimeout=200

 # Inactivity time (in ms) to end TX Service Period while in IBSS power save mode
 gIbssTxSpEndInactivityTime=10

 gEnableModulatedDTIM=2
 gMaxLIModulatedDTIM=6

 #############################################
 # Roaming related configurations
 #############################################
 # CSR Roaming Enable(1) Disable(0)
 gRoamingTime=0

 # ESE Support and fast transition
 EseEnabled=1

 gNeighborLookupThreshold=76
 gNeighborReassocThreshold=81
 gNeighborScanChannelMinTime=20
 gNeighborScanChannelMaxTime=30
 gMaxNeighborReqTries=3

 # To enable, set gRoamIntraBand=1 (Roaming within band)
 # To disable, set gRoamIntraBand=0 (Roaming across band)
 gRoamIntraBand=0

 # Legacy (non-ESE, non-802.11r) Fast Roaming Support
 # To enable, set FastRoamEnabled=1
 # To disable, set FastRoamEnabled=0
 FastRoamEnabled=1

 #Check if the AP to which we are roaming is better than current AP in terms of RSSI.
 #Checking is disabled if set to Zero.Otherwise it will use this value as to how better
 #the RSSI of the new/roamable AP should be for roaming
 RoamRssiDiff=3

 # If the RSSI of any available candidate is better than currently associated
 # AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without
 # registering for reassoc threshold).
 # NOTE: Value of 0 means that we would register for reassoc threshold.
 gImmediateRoamRssiDiff=10

 # 802.11K support
 gRrmEnable=1
 gRrmOperChanMax=8
 gRrmNonOperChanMax=8

 gEnableFastRoamInConcurrency=1

 # Enable/Disable Roaming Offload Support (a.k.a Key Management Offload)
 # 0 to disable, 1 to enable
 gRoamOffloadEnabled=1

 gAllowDFSChannelRoam=1

 # LFR Subnet Detection
 gLFRSubnetDetectionEnable=0

 #############################################
 # Offload related configurations
 #############################################
 # Beacon filtering frequency (unit in beacon intervals)
 gNthBeaconFilter=50

 # Enable WAPI or not
 # WAPIIsEnabled=0
 # Flags to filter Mcast abd Bcast RX packets.
 # Value 0: No filtering, 1: Filter all Multicast.
 # 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
 McastBcastFilter=3

 #Flag to enable HostARPOffload feature or not
 hostArpOffload=1

 #Flag to enable HostNSOffload feature or not
 hostNSOffload=1

 # controlling the following offload patterns
 # through ini parameter. Default value is 1
 # to disable set it to zero. ssdp = 0
 # Setup multicast pattern for mDNS 224.0.0.251,
 # SSDP 239.255.255.250 and LLMNR 224.0.0.252
 ssdp = 0

 #Enable MC address filtering offload
 gMCAddrListEnable=1

 #Enable Active mode offload
 gActiveModeOffload=1

 #Enable Active mode offload
 gEnableActiveModeOffload=1

 #Enable APF in Active mode
 gActiveUcBpfMode=2
 gActiveMcBcBpfMode=1

 #HW CCE Filter mode
 gHwFilterMode=0

 # WOW Enable/Disable.
 # 0 - Disable both magic pattern match and pattern byte match.
 # 1 - Enable magic pattern match on all interfaces.
 # 2 - Enable pattern byte match on all interfaces.
 # 3 - Enable both magic patter and pattern byte match on all interfaces.
 # Default value of gEnableWoW is 3.
 # gEnableWoW=0

 # 11k feature offload
 11k_offload_enable_bitmask=0

 #############################################
 # Logging related configurations
 #############################################
 gEnableLogp=1

 gEnableSelfRecovery=1

 #Enable firmware log
 gEnablefwlog=1
 # Additional firmware log levels
 gFwDebugLogLevel=3
 gFwDebugModuleLoglevel=2,1,3,1,5,1,9,1,13,1,14,1,18,1,19,1,26,1,28,1,29,1,31,1,36,1,38,1,46,1,47,1,50,1,52,1,53,1,56,1,60,1,61,1,4,1

 #Enable firmware uart print
 gEnablefwprint=0

 #############################################
 # TDLS related configurations
 #############################################
 # Enable support for TDLS
 #  0 - disable
 #  1 - enable
 gEnableTDLSSupport=1

 # Enable support for Implicit Trigger of TDLS. That is, wlan driver shall
 # initiate TDLS Discovery towards a peer whenever setup criteria (throughput
 # and RSSI) is met and then will initiate teardown when teardown criteria
 # (idle packet count and RSSI) is met.
 #  0 - disable
 #  1 - enable
 gEnableTDLSImplicitTrigger=1

 # Enable TDLS External Control. That is, user space application has to
 # first configure a peer MAC in wlan driver towards which TDLS is desired.
 # Device will establish TDLS only towards those configured peers whenever
 # TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
 # when teardown criteria (idle packet count and RSSI) is met. However,
 # device will accept TDLS connection if it is initiated from any other peer,
 # even if that peer is not configured.
 #  0 - disable
 #  1 - enable
 # For TDLS External Control, Implicit Trigger must also be enabled.
 gTDLSExternalControl=1

 # Enable support for TDLS off-channel operation
 #  0 - disable
 #  1 - enable
 # TDLS off-channel operation will be invoked when there is only one
 # TDLS connection.
 gEnableTDLSOffChannel=1

 gEnableTDLSScan=1
 gTDLSTxPacketThreshold=10
 gTDLSIdlePacketThreshold=1

 #############################################
 # P2P related configurations
 #############################################
 #P2P Listen offload
 gEnableP2pListenOffload=1

 #Enable or Disable p2p device address administered
 isP2pDeviceAddrAdministrated=0

 #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
 #For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
 #For both active and power save clients.

 #Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
 #If doesn't honor for 5 seconds then DUT remove client.

 #Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on
 #11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
 #Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..

 #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
 #where we send NULL frame.

 #gApLinkMonitorPeriod = 10
 #gGoLinkMonitorPeriod = 10

 #gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
 #Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
 gGoKeepAlivePeriod = 20
 gApKeepAlivePeriod = 20

 #############################################
 # SAP related configurations
 #############################################
 #Enable OBSS protection
 gEnableApOBSSProt=1

 #Enable/Disable UAPSD for SoftAP
 gEnableApUapsd=1

 # SAP auto channel selection configuration
 # 0 = disable auto channel selection
 # 1 = enable auto channel selection, channel provided by supplicant will be ignored
 gApAutoChannelSelection=0

 #SOFTAP Channel Range selection
 gAPChannelSelectStartChannel=1
 gAPChannelSelectEndChannel=11

 # SAP Country code
 # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
 # Example
 #   US Indoor, USI
 #   Korea Outdoor, KRO
 #   Japan without optional byte, JP
 #   France without optional byte, FR
 #gAPCntryCode=USI

 # DFS Master Capability
 gEnableDFSMasterCap=1

 #Auto Shutdown  Value in seconds. A value of 0 means Auto shutoff is disabled
 gAPAutoShutOff=0

 # Remove Overlap channel restriction
 gEnableOverLapCh=0

 # Enable/Disable channel avoidance for SAP in SCC scenario
 # 0 - disable
 # 1 - enable
 gSapSccChanAvoidance=0

 #Enable/Disable Tx beamformee in SAP mode
 gEnableTxBFeeSAP=1

 #Enable/Disable dual MAC feature
 # 0 - enable DBS
 # 1 - disable DBS
 # 2 - disable DBS for connection but keep DBS for scan
 # 3 - disable DBS for connection but keep DBS scan with async
 #     scan policy disabled
 # 4 - enable DBS for connection as well as for scan with async
 #     scan policy disabled
 gDualMacFeatureDisable=1

 #Set priority for connection with bssid_hint
 g_is_bssid_hint_priority=0

 gdbs_scan_selection=5,4,1,16,4,1

 enable_11d_in_world_mode=1

 gEnableLPRx=0

 gDptraceConfig=1,4,1,126

 gAP11ACOverride=0

 #Enable/Disable chain selection optimization for one chain dtim
 #Min: 0
 #MAX: 30
 gEnableDTIMSelectionDiversity=3

 #############################################
 # MAWC related configurations
 #############################################

 # MAWCEnabled - Enable/Disable Motion Aided Wireless Connectivity Global
 MAWCEnabled=0

 # mawc_roam_enabled - Enable/Disable MAWC during roaming
 mawc_roam_enabled=0

 # Enable/Disable the Motion Aided Wireless Connectivity
 # based NLO using this parameter
 mawc_nlo_enabled=0

 # Enable/Disable rtt sta mac randomization
 enable_rtt_mac_randomization=1

 # Channel selection logic DBS (1) vs MCC (0)
 channel_select_logic_conc=0

 gConfigVCmode=0

 # WLM (Wireless Latency Manager)
 wlm_latency_flags_moderate=0
 wlm_latency_flags_low=0
 wlm_latency_flags_ultralow=0

 # OCE Feature
 oce_sta_enable=0
 oce_sap_enable=0
 num_oce_wan_slots=0
 oce_wan_score_idx7_to_4=0
 oce_wan_score_idx11_to_8=0
 oce_enable_rssi_assoc_reject=0

 #Timer waiting for interface up from the upper layer
 gInterfaceChangeWait=1000

 END

 # Note: Configuration parser would not read anything past the END marker
	# This file allows user to override the factory
	# defaults for the WLAN Driver

	#############################################
	# STA related general configurations
	#############################################
	# Assigned MAC Addresses - This will be used until NV items are in place
	# Each byte of MAC address is represented in Hex format as XX
	Intf0MacAddress=000AF58989FF
	Intf1MacAddress=000AF58989FE
	Intf2MacAddress=000AF58989FD
	Intf3MacAddress=000AF58989FC

	#Channel Bonding
	gChannelBondingMode5GHz=1
	gChannelBondingMode24GHz=0

	#Enable Keep alive with non-zero period value
	gStaKeepAlivePeriod=60

	# Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets)
	gVhtMpduLen=2

	# 0 for OLPC 1 for CLPC and SCPC
	gEnableCloseLoop=1

	ImplicitQosIsEnabled=0

	# Enable Tx beamforming in VHT20MHz
	# Valid values are 0,1. If commented out, the default value is 0.
	# 0=disable, 1=enable
	gEnableTxBFin20MHz=1

	#Enable/Disable SU Tx beamformer support.
	gEnableTxSUBeamformer=1

	# 1=enable tx STBC; 0=disable
	gEnableTXSTBC=1

	# 1=enable STBC; 0=disable STBC
	gEnableRXSTBC=1

	# 1=enable rx LDPC; 0=disable
	gEnableRXLDPC=1

	# Flag to allow STA send AddTspec even when ACM is Off
	gAddTSWhenACMIsOff=1

	# RTS threshold
	RTSThreshold=1048576

	# 802.11d support
	g11dSupportEnabled=0


	# Phy Mode (auto, b, g, n, etc)
	# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
	# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
	# 7 = 11b only 8 = 11ac only.
	gDot11Mode=0

	# Enable Rx handling options
	# Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium)
	# Rx_thread + NAPI = 5
	rx_mode=5

	#Enable VHT on 2.4Ghz
	gEnableVhtFor24GHzBand=1

	# Regulatory Setting; 0=STRICT; 1=CUSTOM
	gRegulatoryChangeCountry=1

	# userspace country code setting shld take priority
	gCountryCodePriority=1

	# Enable/Disable LPASS support
	# 0 to disable, 1 to enable
	gEnableLpassSupport=1

	# Enable(1)/Disable(0) SIFS burst
	gEnableSifsBurst=1

	# Tx Chain Mask for CCK
	gCckChainMaskEnable=1

	# Tx Chain Mask for 1SS
	gTxChainMask1ss=0

	# TPC power
	gSelfGenFrmPwr=3

	gReportMaxLinkSpeed=0

	# Use OEM provisioned MAC address
	enable_mac_provision=1

	################ NAN feature set start ###################
	# Enable or Disable NAN
	# 1=Enable (default), 0=Disable
	gEnableNanSupport=1
	genable_nan_datapath=1
	gnan_datapath_ndi_channel=6
	################ NAN feature set end #####################

	gIgnorePeerHTopMode=1
	gIgnorePeerErpInfo=1

	# 802.11n Protection flag
	gEnableApProt=1

	# Fixed Rate
	gFixedRate=0

	# Intra-BSS forward
	gDisableIntraBssFwd=0

	# WMM Enable/Disable
	WmmIsEnabled=0

	# 802.11h support
	g11hSupportEnabled=1

	#Short Guard Interval Enable/disable
	gShortGI20Mhz=1
	gShortGI40Mhz=1

	#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec
	gWlanAutoShutdown=0

	#Preferred band (both or 2.4 only or 5 only)
	BandCapability=0

	gVhtChannelWidth=2

	# Enable Tx beamforming
	gTxBFEnable=1

	# Set txchainmask and rxchainmask
	# These parameters are used only if gEnable2x2 is 0
	# Valid values are 1,2
	# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
	# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
	gSetTxChainmask1x1=1
	gSetRxChainmask1x1=1

	# 2.4GHz Antenna Sharing is not supported
	gForce1x1Exception=0

	#If set to 0, MCC is not allowed.
	gEnableMCCMode=1

	# MCC to SCC Switch mode: 0-Disable 1-Enable 2-Force SCC if same band
	gWlanMccToSccSwitchMode = 0

	# Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k)
	gVhtAmpduLenExponent=7

	# Maximum number of concurrent connections
	gMaxConcurrentActiveSessions=3

	# Radar PRI multiplier
	gDFSradarMappingPriMultiplier=4

	# Enable or Disable Multi-user MIMO
	# 1=Enable (default), 0=Disable
	gEnableMuBformee=1

	# Enable to check FW hash if secure FW feature is enabled. It's for defconfig
	# builds only since it will be ignored in performance/release builds.
	gEnableFWHashCheck=1

	# Enable or Disable MCC Adaptive Scheduler at the FW
	# 1=Enable (default), 0=Disable
	gEnableMCCAdaptiveScheduler=1

	# Disable/Enable GreenAP
	# 0 to disable, 1 to enable, default: 1
	gEnableGreenAp=0

	################ Datapath feature set Begin ################
	# Bus bandwidth threshold values in terms of number of packets
	gBusBandwidthHighThreshold=2000
	gBusBandwidthMediumThreshold=500
	gBusBandwidthLowThreshold=150

	# Bus bandwidth compute timeout value in ms
	gBusBandwidthComputeInterval=100

	# VHT Tx/Rx MCS values
	# Valid values are 0,1,2. If commented out, the default value is 0.
	# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
	gVhtRxMCS=2
	gVhtTxMCS=2

	# VHT Tx/Rx MCS values for 2x2
	# Valid values are 0,1,2. If commented out, the default value is 0.
	# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
	gEnable2x2=1
	gVhtRxMCS2x2=2
	gVhtTxMCS2x2=2

	#IPA config is a bit mask and following are the configurations.
	#bit0 IPA Enable
	#bit1 IPA PRE Filter enable
	#bit2 IPv6 enable
	#bit3 IPA Resource Manager (RM) enable
	#bit4 IPA Clock scaling enable
	#bit5 IPA uC ENABLE
	#bit6 IPA uC STA ENABLE
	#bit8 IPA Real Time Debugging
	gIPAConfig=0x3d
	gIPADescSize=800

	# Enable/Disable RX full reorder offload
	gReorderOffloadSupported=1

	# Enable CE classification
	# 1 - enable(default) 0 - disable
	gCEClassifyEnable=1

	# Enable(Tx) fastpath for data traffic.
	# 1 - enable(default) 0 - disable
	gEnableFastPath=1

	# This flag enables IP, TCP and UDP checksum offload
	# 1 - enable(default) 0 - disable
	gEnableIpTcpUdpChecksumOffload=1

	# Enable TCP Segmentation Offload
	# 1 - enable 0 - disable
	TSOEnable=1

	# Enable HT MPDU Density
	# 4 for 2 micro sec
	ght_mpdu_density=4

	# Enable flow steering to enable multiple CEs for Rx flows.
	# Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs.
	# Parallel Rx paths.
	# 1 - enable 0 - disable(default)
	gEnableFlowSteering=1

	ce_service_max_yield_time=500
	ce_service_max_rx_ind_flush=1
	maxMSDUsPerRxInd=8

	# Data Stall Debugging feature
	gEnableDataStallDetection=0

	# Dynamic configuration of TCP limit output bytes
	gTcpLimitOutputEnable=0

	################ Datapath feature set End ################

	#############################################
	# SCAN related configurations
	#############################################
	# Enable/Disable Idle Scan
	gEnableIdleScan=0

	#Enable Scan Results Aging based on timer
	#Timer value is in seconds
	#If Set to 0 it will not enable the feature
	gScanAgingTime=30

	#Enable Scan Results Aging based on number of scans
	gScanResultAgeCount=1

	#Enable thermal mitigation
	gThermalMitigationEnable=0

	#Maximum Channel time in msec
	gMaxMediumTime=6000

	# Scan Timing Parameters
	# gPassiveMaxChannelTime=110
	# gPassiveMinChannelTime=60
	gActiveMaxChannelTime=40
	gActiveMinChannelTime=20

	gPNOScanSupport=1

	# Enable or Disable Extended Scan (GScan)
	# 1=Enable (default), 0=Disable
	gExtScanEnable=1

	#If set will start with active scan after driver load, otherwise will start with
	#passive scan to find out the domain
	gEnableBypass11d=1

	#If set to 0, will not scan DFS channels
	gEnableDFSChnlScan=1

	#Maxium Channel time in msec
	gMaxMediumTime = 6000

	adaptive_dwell_mode_enabled=1

	hostscan_adaptive_dwell_mode=1

	adapt_dwell_lpf_weight=80

	adapt_dwell_wifi_act_threshold=10

	# Enable or disable Probe Req Information Element whitelist. When enabled, IEs corresponding to bits
	# set in bitmaps are allowed in probe request, all others removed while device is unassociated
	# with an AP
	# 1=Enable, 0=Disable (default)
	g_enable_probereq_whitelist_ies=1

	# ie bitmap examples: <bitmap_name>=<value> [<Allowed Information elements>]
	# g_probe_req_ie_bitmap_0=0x80000009 #[0, 3, 31]
	# g_probe_req_ie_bitmap_0=0x00000000 #[] (default)
	# g_probe_req_ie_bitmap_1=0x80000009 #[32, 35, 63]
	g_probe_req_ie_bitmap_0=0x0000000B
	g_probe_req_ie_bitmap_1=0x00040000
	# g_probe_req_ie_bitmap_2=0x00000000
	# g_probe_req_ie_bitmap_3=0x00000000
	# g_probe_req_ie_bitmap_4=0x00000000
	# g_probe_req_ie_bitmap_5=0x00000000
	g_probe_req_ie_bitmap_6=0x20000000
	# g_probe_req_ie_bitmap_7=0x00000000

	gProbeReqOUIs=0050F208

	#############################################
	# Power related configurations
	#############################################
	# Enable IMPS or not
	gEnableImps=1

	# Enable BMPS or not
	gEnableBmps=1

	# Increase sleep duration (seconds) during IMPS
	# 0 implies no periodic wake up from IMPS. Periodic wakeup is
	# unnecessary if Idle Scan is disabled.
	gImpsModSleepTime=0

	# UAPSD service interval for VO,VI, BE, BK traffic
	InfraUapsdVoSrvIntv=0
	InfraUapsdViSrvIntv=0
	InfraUapsdBeSrvIntv=0
	InfraUapsdBkSrvIntv=0

	# Enable suspend or not
	# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
	gEnableSuspend=3

	#Enable Power Save offload
	gEnablePowerSaveOffload=2

	#Enable Power saving mechanism Based on Android Framework
	#If set to 0 Driver internally control the Power saving mechanism
	#If set to 1 Android Framwrok control the Power saving mechanism
	isAndroidPsEn=0

	beaconEarlyTerminationWakeInterval=3

	#Data Inactivity Timeout when in powersave (in ms)
	gDataInactivityTimeout=200

	# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode
	gIbssTxSpEndInactivityTime=10

	gEnableModulatedDTIM=2
	gMaxLIModulatedDTIM=6

	#############################################
	# Roaming related configurations
	#############################################
	# CSR Roaming Enable(1) Disable(0)
	gRoamingTime=0

	# ESE Support and fast transition
	EseEnabled=1

	gNeighborLookupThreshold=76
	gNeighborReassocThreshold=81
	gNeighborScanChannelMinTime=20
	gNeighborScanChannelMaxTime=30
	gMaxNeighborReqTries=3

	# To enable, set gRoamIntraBand=1 (Roaming within band)
	# To disable, set gRoamIntraBand=0 (Roaming across band)
	gRoamIntraBand=0

	# Legacy (non-ESE, non-802.11r) Fast Roaming Support
	# To enable, set FastRoamEnabled=1
	# To disable, set FastRoamEnabled=0
	FastRoamEnabled=1

	#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
	#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
	#the RSSI of the new/roamable AP should be for roaming
	RoamRssiDiff=3

	# If the RSSI of any available candidate is better than currently associated
	# AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without
	# registering for reassoc threshold).
	# NOTE: Value of 0 means that we would register for reassoc threshold.
	gImmediateRoamRssiDiff=10

	# 802.11K support
	gRrmEnable=1
	gRrmOperChanMax=8
	gRrmNonOperChanMax=8

	gEnableFastRoamInConcurrency=1

	# Enable/Disable Roaming Offload Support (a.k.a Key Management Offload)
	# 0 to disable, 1 to enable
	gRoamOffloadEnabled=1

	gAllowDFSChannelRoam=1

	# LFR Subnet Detection
	gLFRSubnetDetectionEnable=0

	#############################################
	# Offload related configurations
	#############################################
	# Beacon filtering frequency (unit in beacon intervals)
	gNthBeaconFilter=50

	# Enable WAPI or not
	# WAPIIsEnabled=0
	# Flags to filter Mcast abd Bcast RX packets.
	# Value 0: No filtering, 1: Filter all Multicast.
	# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
	McastBcastFilter=3

	#Flag to enable HostARPOffload feature or not
	hostArpOffload=1

	#Flag to enable HostNSOffload feature or not
	hostNSOffload=1

	# controlling the following offload patterns
	# through ini parameter. Default value is 1
	# to disable set it to zero. ssdp = 0
	# Setup multicast pattern for mDNS 224.0.0.251,
	# SSDP 239.255.255.250 and LLMNR 224.0.0.252
	ssdp = 0

	#Enable MC address filtering offload
	gMCAddrListEnable=1

	#Enable Active mode offload
	gActiveModeOffload=1

	#Enable Active mode offload
	gEnableActiveModeOffload=1

	#Enable APF in Active mode
	gActiveUcBpfMode=2
	gActiveMcBcBpfMode=1

	#HW CCE Filter mode
	gHwFilterMode=0

	# WOW Enable/Disable.
	# 0 - Disable both magic pattern match and pattern byte match.
	# 1 - Enable magic pattern match on all interfaces.
	# 2 - Enable pattern byte match on all interfaces.
	# 3 - Enable both magic patter and pattern byte match on all interfaces.
	# Default value of gEnableWoW is 3.
	# gEnableWoW=0

	# 11k feature offload
	11k_offload_enable_bitmask=0

	#############################################
	# Logging related configurations
	#############################################
	gEnableLogp=1

	gEnableSelfRecovery=1

	#Enable firmware log
	gEnablefwlog=1
	# Additional firmware log levels
	gFwDebugLogLevel=3
	gFwDebugModuleLoglevel=2,1,3,1,5,1,9,1,13,1,14,1,18,1,19,1,26,1,28,1,29,1,31,1,36,1,38,1,46,1,47,1,50,1,52,1,53,1,56,1,60,1,61,1,4,1

	#Enable firmware uart print
	gEnablefwprint=0

	#############################################
	# TDLS related configurations
	#############################################
	# Enable support for TDLS
	# 0 - disable
	# 1 - enable
	gEnableTDLSSupport=1

	# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall
	# initiate TDLS Discovery towards a peer whenever setup criteria (throughput
	# and RSSI) is met and then will initiate teardown when teardown criteria
	# (idle packet count and RSSI) is met.
	# 0 - disable
	# 1 - enable
	gEnableTDLSImplicitTrigger=1

	# Enable TDLS External Control. That is, user space application has to
	# first configure a peer MAC in wlan driver towards which TDLS is desired.
	# Device will establish TDLS only towards those configured peers whenever
	# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
	# when teardown criteria (idle packet count and RSSI) is met. However,
	# device will accept TDLS connection if it is initiated from any other peer,
	# even if that peer is not configured.
	# 0 - disable
	# 1 - enable
	# For TDLS External Control, Implicit Trigger must also be enabled.
	gTDLSExternalControl=1

	# Enable support for TDLS off-channel operation
	# 0 - disable
	# 1 - enable
	# TDLS off-channel operation will be invoked when there is only one
	# TDLS connection.
	gEnableTDLSOffChannel=1

	gEnableTDLSScan=1
	gTDLSTxPacketThreshold=10
	gTDLSIdlePacketThreshold=1

	#############################################
	# P2P related configurations
	#############################################
	#P2P Listen offload
	gEnableP2pListenOffload=1

	#Enable or Disable p2p device address administered
	isP2pDeviceAddrAdministrated=0

	#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
	#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
	#For both active and power save clients.

	#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
	#If doesn't honor for 5 seconds then DUT remove client.

	#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on
	#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
	#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..

	#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
	#where we send NULL frame.

	#gApLinkMonitorPeriod = 10
	#gGoLinkMonitorPeriod = 10

	#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
	#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
	gGoKeepAlivePeriod = 20
	gApKeepAlivePeriod = 20

	#############################################
	# SAP related configurations
	#############################################
	#Enable OBSS protection
	gEnableApOBSSProt=1

	#Enable/Disable UAPSD for SoftAP
	gEnableApUapsd=1

	# SAP auto channel selection configuration
	# 0 = disable auto channel selection
	# 1 = enable auto channel selection, channel provided by supplicant will be ignored
	gApAutoChannelSelection=0

	#SOFTAP Channel Range selection
	gAPChannelSelectStartChannel=1
	gAPChannelSelectEndChannel=11

	# SAP Country code
	# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
	# Example
	# US Indoor, USI
	# Korea Outdoor, KRO
	# Japan without optional byte, JP
	# France without optional byte, FR
	#gAPCntryCode=USI

	# DFS Master Capability
	gEnableDFSMasterCap=1

	#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
	gAPAutoShutOff=0

	# Remove Overlap channel restriction
	gEnableOverLapCh=0

	# Enable/Disable channel avoidance for SAP in SCC scenario
	# 0 - disable
	# 1 - enable
	gSapSccChanAvoidance=0

	#Enable/Disable Tx beamformee in SAP mode
	gEnableTxBFeeSAP=1

	#Enable/Disable dual MAC feature
	# 0 - enable DBS
	# 1 - disable DBS
	# 2 - disable DBS for connection but keep DBS for scan
	# 3 - disable DBS for connection but keep DBS scan with async
	# scan policy disabled
	# 4 - enable DBS for connection as well as for scan with async
	# scan policy disabled
	gDualMacFeatureDisable=1

	#Set priority for connection with bssid_hint
	g_is_bssid_hint_priority=0

	gdbs_scan_selection=5,4,1,16,4,1

	enable_11d_in_world_mode=1

	gEnableLPRx=0

	gDptraceConfig=1,4,1,126

	gAP11ACOverride=0

	#Enable/Disable chain selection optimization for one chain dtim
	#Min: 0
	#MAX: 30
	gEnableDTIMSelectionDiversity=3

	#############################################
	# MAWC related configurations
	#############################################

	# MAWCEnabled - Enable/Disable Motion Aided Wireless Connectivity Global
	MAWCEnabled=0

	# mawc_roam_enabled - Enable/Disable MAWC during roaming
	mawc_roam_enabled=0

	# Enable/Disable the Motion Aided Wireless Connectivity
	# based NLO using this parameter
	mawc_nlo_enabled=0

	# Enable/Disable rtt sta mac randomization
	enable_rtt_mac_randomization=1

	# Channel selection logic DBS (1) vs MCC (0)
	channel_select_logic_conc=0

	gConfigVCmode=0

	# WLM (Wireless Latency Manager)
	wlm_latency_flags_moderate=0
	wlm_latency_flags_low=0
	wlm_latency_flags_ultralow=0

	# OCE Feature
	oce_sta_enable=0
	oce_sap_enable=0
	num_oce_wan_slots=0
	oce_wan_score_idx7_to_4=0
	oce_wan_score_idx11_to_8=0
	oce_enable_rssi_assoc_reject=0

	#Timer waiting for interface up from the upper layer
	gInterfaceChangeWait=1000

	END

	# Note: Configuration parser would not read anything past the END marker