| /* SPDX-License-Identifier: GPL-2.0 */ |
| #ifndef LINUX_B43_PHY_COMMON_H_ |
| #define LINUX_B43_PHY_COMMON_H_ |
| |
| #include <linux/types.h> |
| #include <linux/nl80211.h> |
| |
| struct b43_wldev; |
| |
| /* PHY register routing bits */ |
| #define B43_PHYROUTE 0x0C00 /* PHY register routing bits mask */ |
| #define B43_PHYROUTE_BASE 0x0000 /* Base registers */ |
| #define B43_PHYROUTE_OFDM_GPHY 0x0400 /* OFDM register routing for G-PHYs */ |
| #define B43_PHYROUTE_EXT_GPHY 0x0800 /* Extended G-PHY registers */ |
| #define B43_PHYROUTE_N_BMODE 0x0C00 /* N-PHY BMODE registers */ |
| |
| /* CCK (B-PHY) registers. */ |
| #define B43_PHY_CCK(reg) ((reg) | B43_PHYROUTE_BASE) |
| /* N-PHY registers. */ |
| #define B43_PHY_N(reg) ((reg) | B43_PHYROUTE_BASE) |
| /* N-PHY BMODE registers. */ |
| #define B43_PHY_N_BMODE(reg) ((reg) | B43_PHYROUTE_N_BMODE) |
| /* OFDM (A-PHY) registers. */ |
| #define B43_PHY_OFDM(reg) ((reg) | B43_PHYROUTE_OFDM_GPHY) |
| /* Extended G-PHY registers. */ |
| #define B43_PHY_EXTG(reg) ((reg) | B43_PHYROUTE_EXT_GPHY) |
| |
| |
| /* Masks for the PHY versioning registers. */ |
| #define B43_PHYVER_ANALOG 0xF000 |
| #define B43_PHYVER_ANALOG_SHIFT 12 |
| #define B43_PHYVER_TYPE 0x0F00 |
| #define B43_PHYVER_TYPE_SHIFT 8 |
| #define B43_PHYVER_VERSION 0x00FF |
| |
| /* PHY writes need to be flushed if we reach limit */ |
| #define B43_MAX_WRITES_IN_ROW 24 |
| |
| /** |
| * enum b43_interference_mitigation - Interference Mitigation mode |
| * |
| * @B43_INTERFMODE_NONE: Disabled |
| * @B43_INTERFMODE_NONWLAN: Non-WLAN Interference Mitigation |
| * @B43_INTERFMODE_MANUALWLAN: WLAN Interference Mitigation |
| * @B43_INTERFMODE_AUTOWLAN: Automatic WLAN Interference Mitigation |
| */ |
| enum b43_interference_mitigation { |
| B43_INTERFMODE_NONE, |
| B43_INTERFMODE_NONWLAN, |
| B43_INTERFMODE_MANUALWLAN, |
| B43_INTERFMODE_AUTOWLAN, |
| }; |
| |
| /* Antenna identifiers */ |
| enum { |
| B43_ANTENNA0 = 0, /* Antenna 0 */ |
| B43_ANTENNA1 = 1, /* Antenna 1 */ |
| B43_ANTENNA_AUTO0 = 2, /* Automatic, starting with antenna 0 */ |
| B43_ANTENNA_AUTO1 = 3, /* Automatic, starting with antenna 1 */ |
| B43_ANTENNA2 = 4, |
| B43_ANTENNA3 = 8, |
| |
| B43_ANTENNA_AUTO = B43_ANTENNA_AUTO0, |
| B43_ANTENNA_DEFAULT = B43_ANTENNA_AUTO, |
| }; |
| |
| /** |
| * enum b43_txpwr_result - Return value for the recalc_txpower PHY op. |
| * |
| * @B43_TXPWR_RES_NEED_ADJUST: Values changed. Hardware adjustment is needed. |
| * @B43_TXPWR_RES_DONE: No more work to do. Everything is done. |
| */ |
| enum b43_txpwr_result { |
| B43_TXPWR_RES_NEED_ADJUST, |
| B43_TXPWR_RES_DONE, |
| }; |
| |
| /** |
| * struct b43_phy_operations - Function pointers for PHY ops. |
| * |
| * @allocate: Allocate and initialise the PHY data structures. |
| * Must not be NULL. |
| * @free: Destroy and free the PHY data structures. |
| * Must not be NULL. |
| * |
| * @prepare_structs: Prepare the PHY data structures. |
| * The data structures allocated in @allocate are |
| * initialized here. |
| * Must not be NULL. |
| * @prepare_hardware: Prepare the PHY. This is called before b43_chip_init to |
| * do some early early PHY hardware init. |
| * Can be NULL, if not required. |
| * @init: Initialize the PHY. |
| * Must not be NULL. |
| * @exit: Shutdown the PHY. |
| * Can be NULL, if not required. |
| * |
| * @phy_read: Read from a PHY register. |
| * Must not be NULL. |
| * @phy_write: Write to a PHY register. |
| * Must not be NULL. |
| * @phy_maskset: Maskset a PHY register, taking shortcuts. |
| * If it is NULL, a generic algorithm is used. |
| * @radio_read: Read from a Radio register. |
| * Must not be NULL. |
| * @radio_write: Write to a Radio register. |
| * Must not be NULL. |
| * |
| * @supports_hwpctl: Returns a boolean whether Hardware Power Control |
| * is supported or not. |
| * If NULL, hwpctl is assumed to be never supported. |
| * @software_rfkill: Turn the radio ON or OFF. |
| * Possible state values are |
| * RFKILL_STATE_SOFT_BLOCKED or |
| * RFKILL_STATE_UNBLOCKED |
| * Must not be NULL. |
| * @switch_analog: Turn the Analog on/off. |
| * Must not be NULL. |
| * @switch_channel: Switch the radio to another channel. |
| * Must not be NULL. |
| * @get_default_chan: Just returns the default channel number. |
| * Must not be NULL. |
| * @set_rx_antenna: Set the antenna used for RX. |
| * Can be NULL, if not supported. |
| * @interf_mitigation: Switch the Interference Mitigation mode. |
| * Can be NULL, if not supported. |
| * |
| * @recalc_txpower: Recalculate the transmission power parameters. |
| * This callback has to recalculate the TX power settings, |
| * but does not need to write them to the hardware, yet. |
| * Returns enum b43_txpwr_result to indicate whether the hardware |
| * needs to be adjusted. |
| * If B43_TXPWR_NEED_ADJUST is returned, @adjust_txpower |
| * will be called later. |
| * If the parameter "ignore_tssi" is true, the TSSI values should |
| * be ignored and a recalculation of the power settings should be |
| * done even if the TSSI values did not change. |
| * This function may sleep, but should not. |
| * Must not be NULL. |
| * @adjust_txpower: Write the previously calculated TX power settings |
| * (from @recalc_txpower) to the hardware. |
| * This function may sleep. |
| * Can be NULL, if (and ONLY if) @recalc_txpower _always_ |
| * returns B43_TXPWR_RES_DONE. |
| * |
| * @pwork_15sec: Periodic work. Called every 15 seconds. |
| * Can be NULL, if not required. |
| * @pwork_60sec: Periodic work. Called every 60 seconds. |
| * Can be NULL, if not required. |
| */ |
| struct b43_phy_operations { |
| /* Initialisation */ |
| int (*allocate)(struct b43_wldev *dev); |
| void (*free)(struct b43_wldev *dev); |
| void (*prepare_structs)(struct b43_wldev *dev); |
| int (*prepare_hardware)(struct b43_wldev *dev); |
| int (*init)(struct b43_wldev *dev); |
| void (*exit)(struct b43_wldev *dev); |
| |
| /* Register access */ |
| u16 (*phy_read)(struct b43_wldev *dev, u16 reg); |
| void (*phy_write)(struct b43_wldev *dev, u16 reg, u16 value); |
| void (*phy_maskset)(struct b43_wldev *dev, u16 reg, u16 mask, u16 set); |
| u16 (*radio_read)(struct b43_wldev *dev, u16 reg); |
| void (*radio_write)(struct b43_wldev *dev, u16 reg, u16 value); |
| |
| /* Radio */ |
| bool (*supports_hwpctl)(struct b43_wldev *dev); |
| void (*software_rfkill)(struct b43_wldev *dev, bool blocked); |
| void (*switch_analog)(struct b43_wldev *dev, bool on); |
| int (*switch_channel)(struct b43_wldev *dev, unsigned int new_channel); |
| unsigned int (*get_default_chan)(struct b43_wldev *dev); |
| void (*set_rx_antenna)(struct b43_wldev *dev, int antenna); |
| int (*interf_mitigation)(struct b43_wldev *dev, |
| enum b43_interference_mitigation new_mode); |
| |
| /* Transmission power adjustment */ |
| enum b43_txpwr_result (*recalc_txpower)(struct b43_wldev *dev, |
| bool ignore_tssi); |
| void (*adjust_txpower)(struct b43_wldev *dev); |
| |
| /* Misc */ |
| void (*pwork_15sec)(struct b43_wldev *dev); |
| void (*pwork_60sec)(struct b43_wldev *dev); |
| }; |
| |
| struct b43_phy_g; |
| struct b43_phy_n; |
| struct b43_phy_lp; |
| struct b43_phy_ht; |
| struct b43_phy_lcn; |
| |
| struct b43_phy { |
| /* Hardware operation callbacks. */ |
| const struct b43_phy_operations *ops; |
| |
| /* Most hardware context information is stored in the standard- |
| * specific data structures pointed to by the pointers below. |
| * Only one of them is valid (the currently enabled PHY). */ |
| #ifdef CONFIG_B43_DEBUG |
| /* No union for debug build to force NULL derefs in buggy code. */ |
| struct { |
| #else |
| union { |
| #endif |
| /* G-PHY specific information */ |
| struct b43_phy_g *g; |
| /* N-PHY specific information */ |
| struct b43_phy_n *n; |
| /* LP-PHY specific information */ |
| struct b43_phy_lp *lp; |
| /* HT-PHY specific information */ |
| struct b43_phy_ht *ht; |
| /* LCN-PHY specific information */ |
| struct b43_phy_lcn *lcn; |
| /* AC-PHY specific information */ |
| struct b43_phy_ac *ac; |
| }; |
| |
| /* Band support flags. */ |
| bool supports_2ghz; |
| bool supports_5ghz; |
| |
| /* Is GMODE (2 GHz mode) bit enabled? */ |
| bool gmode; |
| |
| /* After power reset full init has to be performed */ |
| bool do_full_init; |
| |
| /* Analog Type */ |
| u8 analog; |
| /* B43_PHYTYPE_ */ |
| u8 type; |
| /* PHY revision number. */ |
| u8 rev; |
| |
| /* Count writes since last read */ |
| u8 writes_counter; |
| |
| /* Radio versioning */ |
| u16 radio_manuf; /* Radio manufacturer */ |
| u16 radio_ver; /* Radio version */ |
| u8 radio_rev; /* Radio revision */ |
| |
| /* Software state of the radio */ |
| bool radio_on; |
| |
| /* Desired TX power level (in dBm). |
| * This is set by the user and adjusted in b43_phy_xmitpower(). */ |
| int desired_txpower; |
| |
| /* Hardware Power Control enabled? */ |
| bool hardware_power_control; |
| |
| /* The time (in absolute jiffies) when the next TX power output |
| * check is needed. */ |
| unsigned long next_txpwr_check_time; |
| |
| /* Current channel */ |
| struct cfg80211_chan_def *chandef; |
| unsigned int channel; |
| |
| /* PHY TX errors counter. */ |
| atomic_t txerr_cnt; |
| |
| #ifdef CONFIG_B43_DEBUG |
| /* PHY registers locked (w.r.t. firmware) */ |
| bool phy_locked; |
| /* Radio registers locked (w.r.t. firmware) */ |
| bool radio_locked; |
| #endif /* B43_DEBUG */ |
| }; |
| |
| |
| /** |
| * b43_phy_allocate - Allocate PHY structs |
| * Allocate the PHY data structures, based on the current dev->phy.type |
| */ |
| int b43_phy_allocate(struct b43_wldev *dev); |
| |
| /** |
| * b43_phy_free - Free PHY structs |
| */ |
| void b43_phy_free(struct b43_wldev *dev); |
| |
| /** |
| * b43_phy_init - Initialise the PHY |
| */ |
| int b43_phy_init(struct b43_wldev *dev); |
| |
| /** |
| * b43_phy_exit - Cleanup PHY |
| */ |
| void b43_phy_exit(struct b43_wldev *dev); |
| |
| /** |
| * b43_has_hardware_pctl - Hardware Power Control supported? |
| * Returns a boolean, whether hardware power control is supported. |
| */ |
| bool b43_has_hardware_pctl(struct b43_wldev *dev); |
| |
| /** |
| * b43_phy_read - 16bit PHY register read access |
| */ |
| u16 b43_phy_read(struct b43_wldev *dev, u16 reg); |
| |
| /** |
| * b43_phy_write - 16bit PHY register write access |
| */ |
| void b43_phy_write(struct b43_wldev *dev, u16 reg, u16 value); |
| |
| /** |
| * b43_phy_copy - copy contents of 16bit PHY register to another |
| */ |
| void b43_phy_copy(struct b43_wldev *dev, u16 destreg, u16 srcreg); |
| |
| /** |
| * b43_phy_mask - Mask a PHY register with a mask |
| */ |
| void b43_phy_mask(struct b43_wldev *dev, u16 offset, u16 mask); |
| |
| /** |
| * b43_phy_set - OR a PHY register with a bitmap |
| */ |
| void b43_phy_set(struct b43_wldev *dev, u16 offset, u16 set); |
| |
| /** |
| * b43_phy_maskset - Mask and OR a PHY register with a mask and bitmap |
| */ |
| void b43_phy_maskset(struct b43_wldev *dev, u16 offset, u16 mask, u16 set); |
| |
| /** |
| * b43_radio_read - 16bit Radio register read access |
| */ |
| u16 b43_radio_read(struct b43_wldev *dev, u16 reg); |
| #define b43_radio_read16 b43_radio_read /* DEPRECATED */ |
| |
| /** |
| * b43_radio_write - 16bit Radio register write access |
| */ |
| void b43_radio_write(struct b43_wldev *dev, u16 reg, u16 value); |
| #define b43_radio_write16 b43_radio_write /* DEPRECATED */ |
| |
| /** |
| * b43_radio_mask - Mask a 16bit radio register with a mask |
| */ |
| void b43_radio_mask(struct b43_wldev *dev, u16 offset, u16 mask); |
| |
| /** |
| * b43_radio_set - OR a 16bit radio register with a bitmap |
| */ |
| void b43_radio_set(struct b43_wldev *dev, u16 offset, u16 set); |
| |
| /** |
| * b43_radio_maskset - Mask and OR a radio register with a mask and bitmap |
| */ |
| void b43_radio_maskset(struct b43_wldev *dev, u16 offset, u16 mask, u16 set); |
| |
| /** |
| * b43_radio_wait_value - Waits for a given value in masked register read |
| */ |
| bool b43_radio_wait_value(struct b43_wldev *dev, u16 offset, u16 mask, |
| u16 value, int delay, int timeout); |
| |
| /** |
| * b43_radio_lock - Lock firmware radio register access |
| */ |
| void b43_radio_lock(struct b43_wldev *dev); |
| |
| /** |
| * b43_radio_unlock - Unlock firmware radio register access |
| */ |
| void b43_radio_unlock(struct b43_wldev *dev); |
| |
| /** |
| * b43_phy_lock - Lock firmware PHY register access |
| */ |
| void b43_phy_lock(struct b43_wldev *dev); |
| |
| /** |
| * b43_phy_unlock - Unlock firmware PHY register access |
| */ |
| void b43_phy_unlock(struct b43_wldev *dev); |
| |
| void b43_phy_put_into_reset(struct b43_wldev *dev); |
| void b43_phy_take_out_of_reset(struct b43_wldev *dev); |
| |
| /** |
| * b43_switch_channel - Switch to another channel |
| */ |
| int b43_switch_channel(struct b43_wldev *dev, unsigned int new_channel); |
| |
| /** |
| * b43_software_rfkill - Turn the radio ON or OFF in software. |
| */ |
| void b43_software_rfkill(struct b43_wldev *dev, bool blocked); |
| |
| /** |
| * b43_phy_txpower_check - Check TX power output. |
| * |
| * Compare the current TX power output to the desired power emission |
| * and schedule an adjustment in case it mismatches. |
| * |
| * @flags: OR'ed enum b43_phy_txpower_check_flags flags. |
| * See the docs below. |
| */ |
| void b43_phy_txpower_check(struct b43_wldev *dev, unsigned int flags); |
| /** |
| * enum b43_phy_txpower_check_flags - Flags for b43_phy_txpower_check() |
| * |
| * @B43_TXPWR_IGNORE_TIME: Ignore the schedule time and force-redo |
| * the check now. |
| * @B43_TXPWR_IGNORE_TSSI: Redo the recalculation, even if the average |
| * TSSI did not change. |
| */ |
| enum b43_phy_txpower_check_flags { |
| B43_TXPWR_IGNORE_TIME = (1 << 0), |
| B43_TXPWR_IGNORE_TSSI = (1 << 1), |
| }; |
| |
| struct work_struct; |
| void b43_phy_txpower_adjust_work(struct work_struct *work); |
| |
| /** |
| * b43_phy_shm_tssi_read - Read the average of the last 4 TSSI from SHM. |
| * |
| * @shm_offset: The SHM address to read the values from. |
| * |
| * Returns the average of the 4 TSSI values, or a negative error code. |
| */ |
| int b43_phy_shm_tssi_read(struct b43_wldev *dev, u16 shm_offset); |
| |
| /** |
| * b43_phy_switch_analog_generic - Generic PHY operation for switching the Analog. |
| * |
| * It does the switching based on the PHY0 core register. |
| * Do _not_ call this directly. Only use it as a switch_analog callback |
| * for struct b43_phy_operations. |
| */ |
| void b43_phyop_switch_analog_generic(struct b43_wldev *dev, bool on); |
| |
| bool b43_is_40mhz(struct b43_wldev *dev); |
| |
| void b43_phy_force_clock(struct b43_wldev *dev, bool force); |
| |
| #endif /* LINUX_B43_PHY_COMMON_H_ */ |
