| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Device Tree for the TVK1281618 R2 UIB |
| */ |
| |
| #include "ste-href-tvk1281618.dtsi" |
| |
| / { |
| soc { |
| i2c@80128000 { |
| accelerometer@19 { |
| compatible = "st,lsm303dlhc-accel"; |
| st,drdy-int-pin = <1>; |
| reg = <0x19>; |
| vdd-supply = <&ab8500_ldo_aux1_reg>; |
| vddio-supply = <&db8500_vsmps2_reg>; |
| interrupt-parent = <&gpio2>; |
| interrupts = <18 IRQ_TYPE_EDGE_RISING>, |
| <19 IRQ_TYPE_EDGE_RISING>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&accel_tvk_mode>; |
| mount-matrix = "0", "-1", "0", |
| "-1", "0", "0", |
| "0", "0", "-1"; |
| }; |
| magnetometer@1e { |
| compatible = "st,lsm303dlm-magn"; |
| st,drdy-int-pin = <1>; |
| reg = <0x1e>; |
| vdd-supply = <&ab8500_ldo_aux1_reg>; |
| vddio-supply = <&db8500_vsmps2_reg>; |
| // This interrupt is not properly working with the driver |
| // interrupt-parent = <&gpio1>; |
| // interrupts = <0 IRQ_TYPE_EDGE_RISING>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&magn_tvk_mode>; |
| }; |
| gyroscope@68 { |
| /* Gyroscope */ |
| compatible = "st,l3g4200d-gyro"; |
| reg = <0x68>; |
| vdd-supply = <&ab8500_ldo_aux1_reg>; |
| vddio-supply = <&db8500_vsmps2_reg>; |
| }; |
| pressure@5c { |
| /* Barometer/pressure sensor */ |
| compatible = "st,lps001wp-press"; |
| reg = <0x5c>; |
| vdd-supply = <&ab8500_ldo_aux1_reg>; |
| vddio-supply = <&db8500_vsmps2_reg>; |
| }; |
| }; |
| |
| mcde@a0350000 { |
| status = "okay"; |
| |
| dsi-controller@a0351000 { |
| panel { |
| compatible = "sony,acx424akp"; |
| reg = <0>; |
| vddi-supply = <&ab8500_ldo_aux1_reg>; |
| reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| }; |
| |
| pinctrl { |
| accelerometer { |
| accel_tvk_mode: accel_tvk { |
| /* Accelerometer interrupt lines 1 & 2 */ |
| tvk_cfg { |
| pins = "GPIO82_C1", "GPIO83_D3"; |
| ste,config = <&gpio_in_pd>; |
| }; |
| }; |
| }; |
| magnetometer { |
| magn_tvk_mode: magn_tvk { |
| /* GPIO 32 used for DRDY, pull this down */ |
| tvk_cfg { |
| pins = "GPIO32_V2"; |
| ste,config = <&gpio_in_pd>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |
