| Kernel driver adm1275 |
| ===================== |
| |
| Supported chips: |
| |
| * Analog Devices ADM1075 |
| |
| Prefix: 'adm1075' |
| |
| Addresses scanned: - |
| |
| Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1075.pdf |
| |
| * Analog Devices ADM1272 |
| |
| Prefix: 'adm1272' |
| |
| Addresses scanned: - |
| |
| Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1272.pdf |
| |
| * Analog Devices ADM1275 |
| |
| Prefix: 'adm1275' |
| |
| Addresses scanned: - |
| |
| Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1275.pdf |
| |
| * Analog Devices ADM1276 |
| |
| Prefix: 'adm1276' |
| |
| Addresses scanned: - |
| |
| Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1276.pdf |
| |
| * Analog Devices ADM1278 |
| |
| Prefix: 'adm1278' |
| |
| Addresses scanned: - |
| |
| Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1278.pdf |
| |
| * Analog Devices ADM1293/ADM1294 |
| |
| Prefix: 'adm1293', 'adm1294' |
| |
| Addresses scanned: - |
| |
| Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1293_1294.pdf |
| |
| Author: Guenter Roeck <linux@roeck-us.net> |
| |
| |
| Description |
| ----------- |
| |
| This driver supports hardware monitoring for Analog Devices ADM1075, ADM1272, |
| ADM1275, ADM1276, ADM1278, ADM1293, and ADM1294 Hot-Swap Controller and |
| Digital Power Monitors. |
| |
| ADM1075, ADM1272, ADM1275, ADM1276, ADM1278, ADM1293, and ADM1294 are hot-swap |
| controllers that allow a circuit board to be removed from or inserted into |
| a live backplane. They also feature current and voltage readback via an |
| integrated 12 bit analog-to-digital converter (ADC), accessed using a |
| PMBus interface. |
| |
| The driver is a client driver to the core PMBus driver. Please see |
| Documentation/hwmon/pmbus.rst for details on PMBus client drivers. |
| |
| |
| Usage Notes |
| ----------- |
| |
| This driver does not auto-detect devices. You will have to instantiate the |
| devices explicitly. Please see Documentation/i2c/instantiating-devices.rst for |
| details. |
| |
| The ADM1075, unlike many other PMBus devices, does not support internal voltage |
| or current scaling. Reported voltages, currents, and power are raw measurements, |
| and will typically have to be scaled. |
| |
| The shunt value in micro-ohms can be set via device tree at compile-time. Please |
| refer to the Documentation/devicetree/bindings/hwmon/adm1275.txt for bindings |
| if the device tree is used. |
| |
| Platform data support |
| --------------------- |
| |
| The driver supports standard PMBus driver platform data. Please see |
| Documentation/hwmon/pmbus.rst for details. |
| |
| |
| Sysfs entries |
| ------------- |
| |
| The following attributes are supported. Limits are read-write, history reset |
| attributes are write-only, all other attributes are read-only. |
| |
| ======================= ======================================================= |
| inX_label "vin1" or "vout1" depending on chip variant and |
| configuration. On ADM1075, ADM1293, and ADM1294, |
| vout1 reports the voltage on the VAUX pin. |
| inX_input Measured voltage. |
| inX_min Minimum Voltage. |
| inX_max Maximum voltage. |
| inX_min_alarm Voltage low alarm. |
| inX_max_alarm Voltage high alarm. |
| inX_highest Historical maximum voltage. |
| inX_reset_history Write any value to reset history. |
| |
| curr1_label "iout1" |
| curr1_input Measured current. |
| curr1_max Maximum current. |
| curr1_max_alarm Current high alarm. |
| curr1_lcrit Critical minimum current. Depending on the chip |
| configuration, either curr1_lcrit or curr1_crit is |
| supported, but not both. |
| curr1_lcrit_alarm Critical current low alarm. |
| curr1_crit Critical maximum current. Depending on the chip |
| configuration, either curr1_lcrit or curr1_crit is |
| supported, but not both. |
| curr1_crit_alarm Critical current high alarm. |
| curr1_highest Historical maximum current. |
| curr1_reset_history Write any value to reset history. |
| |
| power1_label "pin1" |
| power1_input Input power. |
| power1_input_lowest Lowest observed input power. ADM1293 and ADM1294 only. |
| power1_input_highest Highest observed input power. |
| power1_reset_history Write any value to reset history. |
| |
| Power attributes are supported on ADM1075, ADM1272, |
| ADM1276, ADM1293, and ADM1294. |
| |
| temp1_input Chip temperature. |
| temp1_max Maximum chip temperature. |
| temp1_max_alarm Temperature alarm. |
| temp1_crit Critical chip temperature. |
| temp1_crit_alarm Critical temperature high alarm. |
| temp1_highest Highest observed temperature. |
| temp1_reset_history Write any value to reset history. |
| |
| Temperature attributes are supported on ADM1272 and |
| ADM1278. |
| ======================= ======================================================= |
