|  | /* | 
|  | * DRM driver for Pervasive Displays RePaper branded e-ink panels | 
|  | * | 
|  | * Copyright 2013-2017 Pervasive Displays, Inc. | 
|  | * Copyright 2017 Noralf Trønnes | 
|  | * | 
|  | * The driver supports: | 
|  | * Material Film: Aurora Mb (V231) | 
|  | * Driver IC: G2 (eTC) | 
|  | * | 
|  | * The controller code was taken from the userspace driver: | 
|  | * https://github.com/repaper/gratis | 
|  | * | 
|  | * This program is free software; you can redistribute it and/or modify | 
|  | * it under the terms of the GNU General Public License as published by | 
|  | * the Free Software Foundation; either version 2 of the License, or | 
|  | * (at your option) any later version. | 
|  | */ | 
|  |  | 
|  | #include <linux/delay.h> | 
|  | #include <linux/dma-buf.h> | 
|  | #include <linux/gpio/consumer.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/of_device.h> | 
|  | #include <linux/sched/clock.h> | 
|  | #include <linux/spi/spi.h> | 
|  | #include <linux/thermal.h> | 
|  |  | 
|  | #include <drm/drm_atomic_helper.h> | 
|  | #include <drm/drm_damage_helper.h> | 
|  | #include <drm/drm_drv.h> | 
|  | #include <drm/drm_fb_cma_helper.h> | 
|  | #include <drm/drm_fb_helper.h> | 
|  | #include <drm/drm_format_helper.h> | 
|  | #include <drm/drm_gem_cma_helper.h> | 
|  | #include <drm/drm_gem_framebuffer_helper.h> | 
|  | #include <drm/drm_rect.h> | 
|  | #include <drm/drm_vblank.h> | 
|  | #include <drm/drm_simple_kms_helper.h> | 
|  | #include <drm/tinydrm/tinydrm-helpers.h> | 
|  |  | 
|  | #define REPAPER_RID_G2_COG_ID	0x12 | 
|  |  | 
|  | enum repaper_model { | 
|  | E1144CS021 = 1, | 
|  | E1190CS021, | 
|  | E2200CS021, | 
|  | E2271CS021, | 
|  | }; | 
|  |  | 
|  | enum repaper_stage {         /* Image pixel -> Display pixel */ | 
|  | REPAPER_COMPENSATE,  /* B -> W, W -> B (Current Image) */ | 
|  | REPAPER_WHITE,       /* B -> N, W -> W (Current Image) */ | 
|  | REPAPER_INVERSE,     /* B -> N, W -> B (New Image) */ | 
|  | REPAPER_NORMAL       /* B -> B, W -> W (New Image) */ | 
|  | }; | 
|  |  | 
|  | enum repaper_epd_border_byte { | 
|  | REPAPER_BORDER_BYTE_NONE, | 
|  | REPAPER_BORDER_BYTE_ZERO, | 
|  | REPAPER_BORDER_BYTE_SET, | 
|  | }; | 
|  |  | 
|  | struct repaper_epd { | 
|  | struct drm_device drm; | 
|  | struct drm_simple_display_pipe pipe; | 
|  | struct spi_device *spi; | 
|  |  | 
|  | struct gpio_desc *panel_on; | 
|  | struct gpio_desc *border; | 
|  | struct gpio_desc *discharge; | 
|  | struct gpio_desc *reset; | 
|  | struct gpio_desc *busy; | 
|  |  | 
|  | struct thermal_zone_device *thermal; | 
|  |  | 
|  | unsigned int height; | 
|  | unsigned int width; | 
|  | unsigned int bytes_per_scan; | 
|  | const u8 *channel_select; | 
|  | unsigned int stage_time; | 
|  | unsigned int factored_stage_time; | 
|  | bool middle_scan; | 
|  | bool pre_border_byte; | 
|  | enum repaper_epd_border_byte border_byte; | 
|  |  | 
|  | u8 *line_buffer; | 
|  | void *current_frame; | 
|  |  | 
|  | bool enabled; | 
|  | bool cleared; | 
|  | bool partial; | 
|  | }; | 
|  |  | 
|  | static inline struct repaper_epd *drm_to_epd(struct drm_device *drm) | 
|  | { | 
|  | return container_of(drm, struct repaper_epd, drm); | 
|  | } | 
|  |  | 
|  | static int repaper_spi_transfer(struct spi_device *spi, u8 header, | 
|  | const void *tx, void *rx, size_t len) | 
|  | { | 
|  | void *txbuf = NULL, *rxbuf = NULL; | 
|  | struct spi_transfer tr[2] = {}; | 
|  | u8 *headerbuf; | 
|  | int ret; | 
|  |  | 
|  | headerbuf = kmalloc(1, GFP_KERNEL); | 
|  | if (!headerbuf) | 
|  | return -ENOMEM; | 
|  |  | 
|  | headerbuf[0] = header; | 
|  | tr[0].tx_buf = headerbuf; | 
|  | tr[0].len = 1; | 
|  |  | 
|  | /* Stack allocated tx? */ | 
|  | if (tx && len <= 32) { | 
|  | txbuf = kmemdup(tx, len, GFP_KERNEL); | 
|  | if (!txbuf) { | 
|  | ret = -ENOMEM; | 
|  | goto out_free; | 
|  | } | 
|  | } | 
|  |  | 
|  | if (rx) { | 
|  | rxbuf = kmalloc(len, GFP_KERNEL); | 
|  | if (!rxbuf) { | 
|  | ret = -ENOMEM; | 
|  | goto out_free; | 
|  | } | 
|  | } | 
|  |  | 
|  | tr[1].tx_buf = txbuf ? txbuf : tx; | 
|  | tr[1].rx_buf = rxbuf; | 
|  | tr[1].len = len; | 
|  |  | 
|  | ndelay(80); | 
|  | ret = spi_sync_transfer(spi, tr, 2); | 
|  | if (rx && !ret) | 
|  | memcpy(rx, rxbuf, len); | 
|  |  | 
|  | out_free: | 
|  | kfree(headerbuf); | 
|  | kfree(txbuf); | 
|  | kfree(rxbuf); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int repaper_write_buf(struct spi_device *spi, u8 reg, | 
|  | const u8 *buf, size_t len) | 
|  | { | 
|  | int ret; | 
|  |  | 
|  | ret = repaper_spi_transfer(spi, 0x70, ®, NULL, 1); | 
|  | if (ret) | 
|  | return ret; | 
|  |  | 
|  | return repaper_spi_transfer(spi, 0x72, buf, NULL, len); | 
|  | } | 
|  |  | 
|  | static int repaper_write_val(struct spi_device *spi, u8 reg, u8 val) | 
|  | { | 
|  | return repaper_write_buf(spi, reg, &val, 1); | 
|  | } | 
|  |  | 
|  | static int repaper_read_val(struct spi_device *spi, u8 reg) | 
|  | { | 
|  | int ret; | 
|  | u8 val; | 
|  |  | 
|  | ret = repaper_spi_transfer(spi, 0x70, ®, NULL, 1); | 
|  | if (ret) | 
|  | return ret; | 
|  |  | 
|  | ret = repaper_spi_transfer(spi, 0x73, NULL, &val, 1); | 
|  |  | 
|  | return ret ? ret : val; | 
|  | } | 
|  |  | 
|  | static int repaper_read_id(struct spi_device *spi) | 
|  | { | 
|  | int ret; | 
|  | u8 id; | 
|  |  | 
|  | ret = repaper_spi_transfer(spi, 0x71, NULL, &id, 1); | 
|  |  | 
|  | return ret ? ret : id; | 
|  | } | 
|  |  | 
|  | static void repaper_spi_mosi_low(struct spi_device *spi) | 
|  | { | 
|  | const u8 buf[1] = { 0 }; | 
|  |  | 
|  | spi_write(spi, buf, 1); | 
|  | } | 
|  |  | 
|  | /* pixels on display are numbered from 1 so even is actually bits 1,3,5,... */ | 
|  | static void repaper_even_pixels(struct repaper_epd *epd, u8 **pp, | 
|  | const u8 *data, u8 fixed_value, const u8 *mask, | 
|  | enum repaper_stage stage) | 
|  | { | 
|  | unsigned int b; | 
|  |  | 
|  | for (b = 0; b < (epd->width / 8); b++) { | 
|  | if (data) { | 
|  | u8 pixels = data[b] & 0xaa; | 
|  | u8 pixel_mask = 0xff; | 
|  | u8 p1, p2, p3, p4; | 
|  |  | 
|  | if (mask) { | 
|  | pixel_mask = (mask[b] ^ pixels) & 0xaa; | 
|  | pixel_mask |= pixel_mask >> 1; | 
|  | } | 
|  |  | 
|  | switch (stage) { | 
|  | case REPAPER_COMPENSATE: /* B -> W, W -> B (Current) */ | 
|  | pixels = 0xaa | ((pixels ^ 0xaa) >> 1); | 
|  | break; | 
|  | case REPAPER_WHITE:      /* B -> N, W -> W (Current) */ | 
|  | pixels = 0x55 + ((pixels ^ 0xaa) >> 1); | 
|  | break; | 
|  | case REPAPER_INVERSE:    /* B -> N, W -> B (New) */ | 
|  | pixels = 0x55 | (pixels ^ 0xaa); | 
|  | break; | 
|  | case REPAPER_NORMAL:     /* B -> B, W -> W (New) */ | 
|  | pixels = 0xaa | (pixels >> 1); | 
|  | break; | 
|  | } | 
|  |  | 
|  | pixels = (pixels & pixel_mask) | (~pixel_mask & 0x55); | 
|  | p1 = (pixels >> 6) & 0x03; | 
|  | p2 = (pixels >> 4) & 0x03; | 
|  | p3 = (pixels >> 2) & 0x03; | 
|  | p4 = (pixels >> 0) & 0x03; | 
|  | pixels = (p1 << 0) | (p2 << 2) | (p3 << 4) | (p4 << 6); | 
|  | *(*pp)++ = pixels; | 
|  | } else { | 
|  | *(*pp)++ = fixed_value; | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | /* pixels on display are numbered from 1 so odd is actually bits 0,2,4,... */ | 
|  | static void repaper_odd_pixels(struct repaper_epd *epd, u8 **pp, | 
|  | const u8 *data, u8 fixed_value, const u8 *mask, | 
|  | enum repaper_stage stage) | 
|  | { | 
|  | unsigned int b; | 
|  |  | 
|  | for (b = epd->width / 8; b > 0; b--) { | 
|  | if (data) { | 
|  | u8 pixels = data[b - 1] & 0x55; | 
|  | u8 pixel_mask = 0xff; | 
|  |  | 
|  | if (mask) { | 
|  | pixel_mask = (mask[b - 1] ^ pixels) & 0x55; | 
|  | pixel_mask |= pixel_mask << 1; | 
|  | } | 
|  |  | 
|  | switch (stage) { | 
|  | case REPAPER_COMPENSATE: /* B -> W, W -> B (Current) */ | 
|  | pixels = 0xaa | (pixels ^ 0x55); | 
|  | break; | 
|  | case REPAPER_WHITE:      /* B -> N, W -> W (Current) */ | 
|  | pixels = 0x55 + (pixels ^ 0x55); | 
|  | break; | 
|  | case REPAPER_INVERSE:    /* B -> N, W -> B (New) */ | 
|  | pixels = 0x55 | ((pixels ^ 0x55) << 1); | 
|  | break; | 
|  | case REPAPER_NORMAL:     /* B -> B, W -> W (New) */ | 
|  | pixels = 0xaa | pixels; | 
|  | break; | 
|  | } | 
|  |  | 
|  | pixels = (pixels & pixel_mask) | (~pixel_mask & 0x55); | 
|  | *(*pp)++ = pixels; | 
|  | } else { | 
|  | *(*pp)++ = fixed_value; | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | /* interleave bits: (byte)76543210 -> (16 bit).7.6.5.4.3.2.1 */ | 
|  | static inline u16 repaper_interleave_bits(u16 value) | 
|  | { | 
|  | value = (value | (value << 4)) & 0x0f0f; | 
|  | value = (value | (value << 2)) & 0x3333; | 
|  | value = (value | (value << 1)) & 0x5555; | 
|  |  | 
|  | return value; | 
|  | } | 
|  |  | 
|  | /* pixels on display are numbered from 1 */ | 
|  | static void repaper_all_pixels(struct repaper_epd *epd, u8 **pp, | 
|  | const u8 *data, u8 fixed_value, const u8 *mask, | 
|  | enum repaper_stage stage) | 
|  | { | 
|  | unsigned int b; | 
|  |  | 
|  | for (b = epd->width / 8; b > 0; b--) { | 
|  | if (data) { | 
|  | u16 pixels = repaper_interleave_bits(data[b - 1]); | 
|  | u16 pixel_mask = 0xffff; | 
|  |  | 
|  | if (mask) { | 
|  | pixel_mask = repaper_interleave_bits(mask[b - 1]); | 
|  |  | 
|  | pixel_mask = (pixel_mask ^ pixels) & 0x5555; | 
|  | pixel_mask |= pixel_mask << 1; | 
|  | } | 
|  |  | 
|  | switch (stage) { | 
|  | case REPAPER_COMPENSATE: /* B -> W, W -> B (Current) */ | 
|  | pixels = 0xaaaa | (pixels ^ 0x5555); | 
|  | break; | 
|  | case REPAPER_WHITE:      /* B -> N, W -> W (Current) */ | 
|  | pixels = 0x5555 + (pixels ^ 0x5555); | 
|  | break; | 
|  | case REPAPER_INVERSE:    /* B -> N, W -> B (New) */ | 
|  | pixels = 0x5555 | ((pixels ^ 0x5555) << 1); | 
|  | break; | 
|  | case REPAPER_NORMAL:     /* B -> B, W -> W (New) */ | 
|  | pixels = 0xaaaa | pixels; | 
|  | break; | 
|  | } | 
|  |  | 
|  | pixels = (pixels & pixel_mask) | (~pixel_mask & 0x5555); | 
|  | *(*pp)++ = pixels >> 8; | 
|  | *(*pp)++ = pixels; | 
|  | } else { | 
|  | *(*pp)++ = fixed_value; | 
|  | *(*pp)++ = fixed_value; | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | /* output one line of scan and data bytes to the display */ | 
|  | static void repaper_one_line(struct repaper_epd *epd, unsigned int line, | 
|  | const u8 *data, u8 fixed_value, const u8 *mask, | 
|  | enum repaper_stage stage) | 
|  | { | 
|  | u8 *p = epd->line_buffer; | 
|  | unsigned int b; | 
|  |  | 
|  | repaper_spi_mosi_low(epd->spi); | 
|  |  | 
|  | if (epd->pre_border_byte) | 
|  | *p++ = 0x00; | 
|  |  | 
|  | if (epd->middle_scan) { | 
|  | /* data bytes */ | 
|  | repaper_odd_pixels(epd, &p, data, fixed_value, mask, stage); | 
|  |  | 
|  | /* scan line */ | 
|  | for (b = epd->bytes_per_scan; b > 0; b--) { | 
|  | if (line / 4 == b - 1) | 
|  | *p++ = 0x03 << (2 * (line & 0x03)); | 
|  | else | 
|  | *p++ = 0x00; | 
|  | } | 
|  |  | 
|  | /* data bytes */ | 
|  | repaper_even_pixels(epd, &p, data, fixed_value, mask, stage); | 
|  | } else { | 
|  | /* | 
|  | * even scan line, but as lines on display are numbered from 1, | 
|  | * line: 1,3,5,... | 
|  | */ | 
|  | for (b = 0; b < epd->bytes_per_scan; b++) { | 
|  | if (0 != (line & 0x01) && line / 8 == b) | 
|  | *p++ = 0xc0 >> (line & 0x06); | 
|  | else | 
|  | *p++ = 0x00; | 
|  | } | 
|  |  | 
|  | /* data bytes */ | 
|  | repaper_all_pixels(epd, &p, data, fixed_value, mask, stage); | 
|  |  | 
|  | /* | 
|  | * odd scan line, but as lines on display are numbered from 1, | 
|  | * line: 0,2,4,6,... | 
|  | */ | 
|  | for (b = epd->bytes_per_scan; b > 0; b--) { | 
|  | if (0 == (line & 0x01) && line / 8 == b - 1) | 
|  | *p++ = 0x03 << (line & 0x06); | 
|  | else | 
|  | *p++ = 0x00; | 
|  | } | 
|  | } | 
|  |  | 
|  | switch (epd->border_byte) { | 
|  | case REPAPER_BORDER_BYTE_NONE: | 
|  | break; | 
|  |  | 
|  | case REPAPER_BORDER_BYTE_ZERO: | 
|  | *p++ = 0x00; | 
|  | break; | 
|  |  | 
|  | case REPAPER_BORDER_BYTE_SET: | 
|  | switch (stage) { | 
|  | case REPAPER_COMPENSATE: | 
|  | case REPAPER_WHITE: | 
|  | case REPAPER_INVERSE: | 
|  | *p++ = 0x00; | 
|  | break; | 
|  | case REPAPER_NORMAL: | 
|  | *p++ = 0xaa; | 
|  | break; | 
|  | } | 
|  | break; | 
|  | } | 
|  |  | 
|  | repaper_write_buf(epd->spi, 0x0a, epd->line_buffer, | 
|  | p - epd->line_buffer); | 
|  |  | 
|  | /* Output data to panel */ | 
|  | repaper_write_val(epd->spi, 0x02, 0x07); | 
|  |  | 
|  | repaper_spi_mosi_low(epd->spi); | 
|  | } | 
|  |  | 
|  | static void repaper_frame_fixed(struct repaper_epd *epd, u8 fixed_value, | 
|  | enum repaper_stage stage) | 
|  | { | 
|  | unsigned int line; | 
|  |  | 
|  | for (line = 0; line < epd->height; line++) | 
|  | repaper_one_line(epd, line, NULL, fixed_value, NULL, stage); | 
|  | } | 
|  |  | 
|  | static void repaper_frame_data(struct repaper_epd *epd, const u8 *image, | 
|  | const u8 *mask, enum repaper_stage stage) | 
|  | { | 
|  | unsigned int line; | 
|  |  | 
|  | if (!mask) { | 
|  | for (line = 0; line < epd->height; line++) { | 
|  | repaper_one_line(epd, line, | 
|  | &image[line * (epd->width / 8)], | 
|  | 0, NULL, stage); | 
|  | } | 
|  | } else { | 
|  | for (line = 0; line < epd->height; line++) { | 
|  | size_t n = line * epd->width / 8; | 
|  |  | 
|  | repaper_one_line(epd, line, &image[n], 0, &mask[n], | 
|  | stage); | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | static void repaper_frame_fixed_repeat(struct repaper_epd *epd, u8 fixed_value, | 
|  | enum repaper_stage stage) | 
|  | { | 
|  | u64 start = local_clock(); | 
|  | u64 end = start + (epd->factored_stage_time * 1000 * 1000); | 
|  |  | 
|  | do { | 
|  | repaper_frame_fixed(epd, fixed_value, stage); | 
|  | } while (local_clock() < end); | 
|  | } | 
|  |  | 
|  | static void repaper_frame_data_repeat(struct repaper_epd *epd, const u8 *image, | 
|  | const u8 *mask, enum repaper_stage stage) | 
|  | { | 
|  | u64 start = local_clock(); | 
|  | u64 end = start + (epd->factored_stage_time * 1000 * 1000); | 
|  |  | 
|  | do { | 
|  | repaper_frame_data(epd, image, mask, stage); | 
|  | } while (local_clock() < end); | 
|  | } | 
|  |  | 
|  | static void repaper_get_temperature(struct repaper_epd *epd) | 
|  | { | 
|  | int ret, temperature = 0; | 
|  | unsigned int factor10x; | 
|  |  | 
|  | if (!epd->thermal) | 
|  | return; | 
|  |  | 
|  | ret = thermal_zone_get_temp(epd->thermal, &temperature); | 
|  | if (ret) { | 
|  | DRM_DEV_ERROR(&epd->spi->dev, "Failed to get temperature (%d)\n", ret); | 
|  | return; | 
|  | } | 
|  |  | 
|  | temperature /= 1000; | 
|  |  | 
|  | if (temperature <= -10) | 
|  | factor10x = 170; | 
|  | else if (temperature <= -5) | 
|  | factor10x = 120; | 
|  | else if (temperature <= 5) | 
|  | factor10x = 80; | 
|  | else if (temperature <= 10) | 
|  | factor10x = 40; | 
|  | else if (temperature <= 15) | 
|  | factor10x = 30; | 
|  | else if (temperature <= 20) | 
|  | factor10x = 20; | 
|  | else if (temperature <= 40) | 
|  | factor10x = 10; | 
|  | else | 
|  | factor10x = 7; | 
|  |  | 
|  | epd->factored_stage_time = epd->stage_time * factor10x / 10; | 
|  | } | 
|  |  | 
|  | static void repaper_gray8_to_mono_reversed(u8 *buf, u32 width, u32 height) | 
|  | { | 
|  | u8 *gray8 = buf, *mono = buf; | 
|  | int y, xb, i; | 
|  |  | 
|  | for (y = 0; y < height; y++) | 
|  | for (xb = 0; xb < width / 8; xb++) { | 
|  | u8 byte = 0x00; | 
|  |  | 
|  | for (i = 0; i < 8; i++) { | 
|  | int x = xb * 8 + i; | 
|  |  | 
|  | byte >>= 1; | 
|  | if (gray8[y * width + x] >> 7) | 
|  | byte |= BIT(7); | 
|  | } | 
|  | *mono++ = byte; | 
|  | } | 
|  | } | 
|  |  | 
|  | static int repaper_fb_dirty(struct drm_framebuffer *fb) | 
|  | { | 
|  | struct drm_gem_cma_object *cma_obj = drm_fb_cma_get_gem_obj(fb, 0); | 
|  | struct dma_buf_attachment *import_attach = cma_obj->base.import_attach; | 
|  | struct repaper_epd *epd = drm_to_epd(fb->dev); | 
|  | struct drm_rect clip; | 
|  | int idx, ret = 0; | 
|  | u8 *buf = NULL; | 
|  |  | 
|  | if (!epd->enabled) | 
|  | return 0; | 
|  |  | 
|  | if (!drm_dev_enter(fb->dev, &idx)) | 
|  | return -ENODEV; | 
|  |  | 
|  | /* repaper can't do partial updates */ | 
|  | clip.x1 = 0; | 
|  | clip.x2 = fb->width; | 
|  | clip.y1 = 0; | 
|  | clip.y2 = fb->height; | 
|  |  | 
|  | repaper_get_temperature(epd); | 
|  |  | 
|  | DRM_DEBUG("Flushing [FB:%d] st=%ums\n", fb->base.id, | 
|  | epd->factored_stage_time); | 
|  |  | 
|  | buf = kmalloc_array(fb->width, fb->height, GFP_KERNEL); | 
|  | if (!buf) { | 
|  | ret = -ENOMEM; | 
|  | goto out_exit; | 
|  | } | 
|  |  | 
|  | if (import_attach) { | 
|  | ret = dma_buf_begin_cpu_access(import_attach->dmabuf, | 
|  | DMA_FROM_DEVICE); | 
|  | if (ret) | 
|  | goto out_free; | 
|  | } | 
|  |  | 
|  | drm_fb_xrgb8888_to_gray8(buf, cma_obj->vaddr, fb, &clip); | 
|  |  | 
|  | if (import_attach) { | 
|  | ret = dma_buf_end_cpu_access(import_attach->dmabuf, | 
|  | DMA_FROM_DEVICE); | 
|  | if (ret) | 
|  | goto out_free; | 
|  | } | 
|  |  | 
|  | repaper_gray8_to_mono_reversed(buf, fb->width, fb->height); | 
|  |  | 
|  | if (epd->partial) { | 
|  | repaper_frame_data_repeat(epd, buf, epd->current_frame, | 
|  | REPAPER_NORMAL); | 
|  | } else if (epd->cleared) { | 
|  | repaper_frame_data_repeat(epd, epd->current_frame, NULL, | 
|  | REPAPER_COMPENSATE); | 
|  | repaper_frame_data_repeat(epd, epd->current_frame, NULL, | 
|  | REPAPER_WHITE); | 
|  | repaper_frame_data_repeat(epd, buf, NULL, REPAPER_INVERSE); | 
|  | repaper_frame_data_repeat(epd, buf, NULL, REPAPER_NORMAL); | 
|  |  | 
|  | epd->partial = true; | 
|  | } else { | 
|  | /* Clear display (anything -> white) */ | 
|  | repaper_frame_fixed_repeat(epd, 0xff, REPAPER_COMPENSATE); | 
|  | repaper_frame_fixed_repeat(epd, 0xff, REPAPER_WHITE); | 
|  | repaper_frame_fixed_repeat(epd, 0xaa, REPAPER_INVERSE); | 
|  | repaper_frame_fixed_repeat(epd, 0xaa, REPAPER_NORMAL); | 
|  |  | 
|  | /* Assuming a clear (white) screen output an image */ | 
|  | repaper_frame_fixed_repeat(epd, 0xaa, REPAPER_COMPENSATE); | 
|  | repaper_frame_fixed_repeat(epd, 0xaa, REPAPER_WHITE); | 
|  | repaper_frame_data_repeat(epd, buf, NULL, REPAPER_INVERSE); | 
|  | repaper_frame_data_repeat(epd, buf, NULL, REPAPER_NORMAL); | 
|  |  | 
|  | epd->cleared = true; | 
|  | epd->partial = true; | 
|  | } | 
|  |  | 
|  | memcpy(epd->current_frame, buf, fb->width * fb->height / 8); | 
|  |  | 
|  | /* | 
|  | * An extra frame write is needed if pixels are set in the bottom line, | 
|  | * or else grey lines rises up from the pixels | 
|  | */ | 
|  | if (epd->pre_border_byte) { | 
|  | unsigned int x; | 
|  |  | 
|  | for (x = 0; x < (fb->width / 8); x++) | 
|  | if (buf[x + (fb->width * (fb->height - 1) / 8)]) { | 
|  | repaper_frame_data_repeat(epd, buf, | 
|  | epd->current_frame, | 
|  | REPAPER_NORMAL); | 
|  | break; | 
|  | } | 
|  | } | 
|  |  | 
|  | out_free: | 
|  | kfree(buf); | 
|  | out_exit: | 
|  | drm_dev_exit(idx); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static void power_off(struct repaper_epd *epd) | 
|  | { | 
|  | /* Turn off power and all signals */ | 
|  | gpiod_set_value_cansleep(epd->reset, 0); | 
|  | gpiod_set_value_cansleep(epd->panel_on, 0); | 
|  | if (epd->border) | 
|  | gpiod_set_value_cansleep(epd->border, 0); | 
|  |  | 
|  | /* Ensure SPI MOSI and CLOCK are Low before CS Low */ | 
|  | repaper_spi_mosi_low(epd->spi); | 
|  |  | 
|  | /* Discharge pulse */ | 
|  | gpiod_set_value_cansleep(epd->discharge, 1); | 
|  | msleep(150); | 
|  | gpiod_set_value_cansleep(epd->discharge, 0); | 
|  | } | 
|  |  | 
|  | static void repaper_pipe_enable(struct drm_simple_display_pipe *pipe, | 
|  | struct drm_crtc_state *crtc_state, | 
|  | struct drm_plane_state *plane_state) | 
|  | { | 
|  | struct repaper_epd *epd = drm_to_epd(pipe->crtc.dev); | 
|  | struct spi_device *spi = epd->spi; | 
|  | struct device *dev = &spi->dev; | 
|  | bool dc_ok = false; | 
|  | int i, ret, idx; | 
|  |  | 
|  | if (!drm_dev_enter(pipe->crtc.dev, &idx)) | 
|  | return; | 
|  |  | 
|  | DRM_DEBUG_DRIVER("\n"); | 
|  |  | 
|  | /* Power up sequence */ | 
|  | gpiod_set_value_cansleep(epd->reset, 0); | 
|  | gpiod_set_value_cansleep(epd->panel_on, 0); | 
|  | gpiod_set_value_cansleep(epd->discharge, 0); | 
|  | if (epd->border) | 
|  | gpiod_set_value_cansleep(epd->border, 0); | 
|  | repaper_spi_mosi_low(spi); | 
|  | usleep_range(5000, 10000); | 
|  |  | 
|  | gpiod_set_value_cansleep(epd->panel_on, 1); | 
|  | /* | 
|  | * This delay comes from the repaper.org userspace driver, it's not | 
|  | * mentioned in the datasheet. | 
|  | */ | 
|  | usleep_range(10000, 15000); | 
|  | gpiod_set_value_cansleep(epd->reset, 1); | 
|  | if (epd->border) | 
|  | gpiod_set_value_cansleep(epd->border, 1); | 
|  | usleep_range(5000, 10000); | 
|  | gpiod_set_value_cansleep(epd->reset, 0); | 
|  | usleep_range(5000, 10000); | 
|  | gpiod_set_value_cansleep(epd->reset, 1); | 
|  | usleep_range(5000, 10000); | 
|  |  | 
|  | /* Wait for COG to become ready */ | 
|  | for (i = 100; i > 0; i--) { | 
|  | if (!gpiod_get_value_cansleep(epd->busy)) | 
|  | break; | 
|  |  | 
|  | usleep_range(10, 100); | 
|  | } | 
|  |  | 
|  | if (!i) { | 
|  | DRM_DEV_ERROR(dev, "timeout waiting for panel to become ready.\n"); | 
|  | power_off(epd); | 
|  | goto out_exit; | 
|  | } | 
|  |  | 
|  | repaper_read_id(spi); | 
|  | ret = repaper_read_id(spi); | 
|  | if (ret != REPAPER_RID_G2_COG_ID) { | 
|  | if (ret < 0) | 
|  | dev_err(dev, "failed to read chip (%d)\n", ret); | 
|  | else | 
|  | dev_err(dev, "wrong COG ID 0x%02x\n", ret); | 
|  | power_off(epd); | 
|  | goto out_exit; | 
|  | } | 
|  |  | 
|  | /* Disable OE */ | 
|  | repaper_write_val(spi, 0x02, 0x40); | 
|  |  | 
|  | ret = repaper_read_val(spi, 0x0f); | 
|  | if (ret < 0 || !(ret & 0x80)) { | 
|  | if (ret < 0) | 
|  | DRM_DEV_ERROR(dev, "failed to read chip (%d)\n", ret); | 
|  | else | 
|  | DRM_DEV_ERROR(dev, "panel is reported broken\n"); | 
|  | power_off(epd); | 
|  | goto out_exit; | 
|  | } | 
|  |  | 
|  | /* Power saving mode */ | 
|  | repaper_write_val(spi, 0x0b, 0x02); | 
|  | /* Channel select */ | 
|  | repaper_write_buf(spi, 0x01, epd->channel_select, 8); | 
|  | /* High power mode osc */ | 
|  | repaper_write_val(spi, 0x07, 0xd1); | 
|  | /* Power setting */ | 
|  | repaper_write_val(spi, 0x08, 0x02); | 
|  | /* Vcom level */ | 
|  | repaper_write_val(spi, 0x09, 0xc2); | 
|  | /* Power setting */ | 
|  | repaper_write_val(spi, 0x04, 0x03); | 
|  | /* Driver latch on */ | 
|  | repaper_write_val(spi, 0x03, 0x01); | 
|  | /* Driver latch off */ | 
|  | repaper_write_val(spi, 0x03, 0x00); | 
|  | usleep_range(5000, 10000); | 
|  |  | 
|  | /* Start chargepump */ | 
|  | for (i = 0; i < 4; ++i) { | 
|  | /* Charge pump positive voltage on - VGH/VDL on */ | 
|  | repaper_write_val(spi, 0x05, 0x01); | 
|  | msleep(240); | 
|  |  | 
|  | /* Charge pump negative voltage on - VGL/VDL on */ | 
|  | repaper_write_val(spi, 0x05, 0x03); | 
|  | msleep(40); | 
|  |  | 
|  | /* Charge pump Vcom on - Vcom driver on */ | 
|  | repaper_write_val(spi, 0x05, 0x0f); | 
|  | msleep(40); | 
|  |  | 
|  | /* check DC/DC */ | 
|  | ret = repaper_read_val(spi, 0x0f); | 
|  | if (ret < 0) { | 
|  | DRM_DEV_ERROR(dev, "failed to read chip (%d)\n", ret); | 
|  | power_off(epd); | 
|  | goto out_exit; | 
|  | } | 
|  |  | 
|  | if (ret & 0x40) { | 
|  | dc_ok = true; | 
|  | break; | 
|  | } | 
|  | } | 
|  |  | 
|  | if (!dc_ok) { | 
|  | DRM_DEV_ERROR(dev, "dc/dc failed\n"); | 
|  | power_off(epd); | 
|  | goto out_exit; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Output enable to disable | 
|  | * The userspace driver sets this to 0x04, but the datasheet says 0x06 | 
|  | */ | 
|  | repaper_write_val(spi, 0x02, 0x04); | 
|  |  | 
|  | epd->enabled = true; | 
|  | epd->partial = false; | 
|  | out_exit: | 
|  | drm_dev_exit(idx); | 
|  | } | 
|  |  | 
|  | static void repaper_pipe_disable(struct drm_simple_display_pipe *pipe) | 
|  | { | 
|  | struct repaper_epd *epd = drm_to_epd(pipe->crtc.dev); | 
|  | struct spi_device *spi = epd->spi; | 
|  | unsigned int line; | 
|  |  | 
|  | /* | 
|  | * This callback is not protected by drm_dev_enter/exit since we want to | 
|  | * turn off the display on regular driver unload. It's highly unlikely | 
|  | * that the underlying SPI controller is gone should this be called after | 
|  | * unplug. | 
|  | */ | 
|  |  | 
|  | if (!epd->enabled) | 
|  | return; | 
|  |  | 
|  | DRM_DEBUG_DRIVER("\n"); | 
|  |  | 
|  | epd->enabled = false; | 
|  |  | 
|  | /* Nothing frame */ | 
|  | for (line = 0; line < epd->height; line++) | 
|  | repaper_one_line(epd, 0x7fffu, NULL, 0x00, NULL, | 
|  | REPAPER_COMPENSATE); | 
|  |  | 
|  | /* 2.7" */ | 
|  | if (epd->border) { | 
|  | /* Dummy line */ | 
|  | repaper_one_line(epd, 0x7fffu, NULL, 0x00, NULL, | 
|  | REPAPER_COMPENSATE); | 
|  | msleep(25); | 
|  | gpiod_set_value_cansleep(epd->border, 0); | 
|  | msleep(200); | 
|  | gpiod_set_value_cansleep(epd->border, 1); | 
|  | } else { | 
|  | /* Border dummy line */ | 
|  | repaper_one_line(epd, 0x7fffu, NULL, 0x00, NULL, | 
|  | REPAPER_NORMAL); | 
|  | msleep(200); | 
|  | } | 
|  |  | 
|  | /* not described in datasheet */ | 
|  | repaper_write_val(spi, 0x0b, 0x00); | 
|  | /* Latch reset turn on */ | 
|  | repaper_write_val(spi, 0x03, 0x01); | 
|  | /* Power off charge pump Vcom */ | 
|  | repaper_write_val(spi, 0x05, 0x03); | 
|  | /* Power off charge pump neg voltage */ | 
|  | repaper_write_val(spi, 0x05, 0x01); | 
|  | msleep(120); | 
|  | /* Discharge internal */ | 
|  | repaper_write_val(spi, 0x04, 0x80); | 
|  | /* turn off all charge pumps */ | 
|  | repaper_write_val(spi, 0x05, 0x00); | 
|  | /* Turn off osc */ | 
|  | repaper_write_val(spi, 0x07, 0x01); | 
|  | msleep(50); | 
|  |  | 
|  | power_off(epd); | 
|  | } | 
|  |  | 
|  | static void repaper_pipe_update(struct drm_simple_display_pipe *pipe, | 
|  | struct drm_plane_state *old_state) | 
|  | { | 
|  | struct drm_plane_state *state = pipe->plane.state; | 
|  | struct drm_crtc *crtc = &pipe->crtc; | 
|  | struct drm_rect rect; | 
|  |  | 
|  | if (drm_atomic_helper_damage_merged(old_state, state, &rect)) | 
|  | repaper_fb_dirty(state->fb); | 
|  |  | 
|  | if (crtc->state->event) { | 
|  | spin_lock_irq(&crtc->dev->event_lock); | 
|  | drm_crtc_send_vblank_event(crtc, crtc->state->event); | 
|  | spin_unlock_irq(&crtc->dev->event_lock); | 
|  | crtc->state->event = NULL; | 
|  | } | 
|  | } | 
|  |  | 
|  | static const struct drm_simple_display_pipe_funcs repaper_pipe_funcs = { | 
|  | .enable = repaper_pipe_enable, | 
|  | .disable = repaper_pipe_disable, | 
|  | .update = repaper_pipe_update, | 
|  | .prepare_fb = drm_gem_fb_simple_display_pipe_prepare_fb, | 
|  | }; | 
|  |  | 
|  | static const struct drm_mode_config_funcs repaper_mode_config_funcs = { | 
|  | .fb_create = drm_gem_fb_create_with_dirty, | 
|  | .atomic_check = drm_atomic_helper_check, | 
|  | .atomic_commit = drm_atomic_helper_commit, | 
|  | }; | 
|  |  | 
|  | static void repaper_release(struct drm_device *drm) | 
|  | { | 
|  | struct repaper_epd *epd = drm_to_epd(drm); | 
|  |  | 
|  | DRM_DEBUG_DRIVER("\n"); | 
|  |  | 
|  | drm_mode_config_cleanup(drm); | 
|  | drm_dev_fini(drm); | 
|  | kfree(epd); | 
|  | } | 
|  |  | 
|  | static const uint32_t repaper_formats[] = { | 
|  | DRM_FORMAT_XRGB8888, | 
|  | }; | 
|  |  | 
|  | static const struct drm_display_mode repaper_e1144cs021_mode = { | 
|  | DRM_SIMPLE_MODE(128, 96, 29, 22), | 
|  | }; | 
|  |  | 
|  | static const u8 repaper_e1144cs021_cs[] = { 0x00, 0x00, 0x00, 0x00, | 
|  | 0x00, 0x0f, 0xff, 0x00 }; | 
|  |  | 
|  | static const struct drm_display_mode repaper_e1190cs021_mode = { | 
|  | DRM_SIMPLE_MODE(144, 128, 36, 32), | 
|  | }; | 
|  |  | 
|  | static const u8 repaper_e1190cs021_cs[] = { 0x00, 0x00, 0x00, 0x03, | 
|  | 0xfc, 0x00, 0x00, 0xff }; | 
|  |  | 
|  | static const struct drm_display_mode repaper_e2200cs021_mode = { | 
|  | DRM_SIMPLE_MODE(200, 96, 46, 22), | 
|  | }; | 
|  |  | 
|  | static const u8 repaper_e2200cs021_cs[] = { 0x00, 0x00, 0x00, 0x00, | 
|  | 0x01, 0xff, 0xe0, 0x00 }; | 
|  |  | 
|  | static const struct drm_display_mode repaper_e2271cs021_mode = { | 
|  | DRM_SIMPLE_MODE(264, 176, 57, 38), | 
|  | }; | 
|  |  | 
|  | static const u8 repaper_e2271cs021_cs[] = { 0x00, 0x00, 0x00, 0x7f, | 
|  | 0xff, 0xfe, 0x00, 0x00 }; | 
|  |  | 
|  | DEFINE_DRM_GEM_CMA_FOPS(repaper_fops); | 
|  |  | 
|  | static struct drm_driver repaper_driver = { | 
|  | .driver_features	= DRIVER_GEM | DRIVER_MODESET | DRIVER_PRIME | | 
|  | DRIVER_ATOMIC, | 
|  | .fops			= &repaper_fops, | 
|  | .release		= repaper_release, | 
|  | DRM_GEM_CMA_VMAP_DRIVER_OPS, | 
|  | .name			= "repaper", | 
|  | .desc			= "Pervasive Displays RePaper e-ink panels", | 
|  | .date			= "20170405", | 
|  | .major			= 1, | 
|  | .minor			= 0, | 
|  | }; | 
|  |  | 
|  | static const struct of_device_id repaper_of_match[] = { | 
|  | { .compatible = "pervasive,e1144cs021", .data = (void *)E1144CS021 }, | 
|  | { .compatible = "pervasive,e1190cs021", .data = (void *)E1190CS021 }, | 
|  | { .compatible = "pervasive,e2200cs021", .data = (void *)E2200CS021 }, | 
|  | { .compatible = "pervasive,e2271cs021", .data = (void *)E2271CS021 }, | 
|  | {}, | 
|  | }; | 
|  | MODULE_DEVICE_TABLE(of, repaper_of_match); | 
|  |  | 
|  | static const struct spi_device_id repaper_id[] = { | 
|  | { "e1144cs021", E1144CS021 }, | 
|  | { "e1190cs021", E1190CS021 }, | 
|  | { "e2200cs021", E2200CS021 }, | 
|  | { "e2271cs021", E2271CS021 }, | 
|  | { }, | 
|  | }; | 
|  | MODULE_DEVICE_TABLE(spi, repaper_id); | 
|  |  | 
|  | static int repaper_probe(struct spi_device *spi) | 
|  | { | 
|  | const struct drm_display_mode *mode; | 
|  | const struct spi_device_id *spi_id; | 
|  | const struct of_device_id *match; | 
|  | struct device *dev = &spi->dev; | 
|  | enum repaper_model model; | 
|  | const char *thermal_zone; | 
|  | struct repaper_epd *epd; | 
|  | size_t line_buffer_size; | 
|  | struct drm_device *drm; | 
|  | int ret; | 
|  |  | 
|  | match = of_match_device(repaper_of_match, dev); | 
|  | if (match) { | 
|  | model = (enum repaper_model)match->data; | 
|  | } else { | 
|  | spi_id = spi_get_device_id(spi); | 
|  | model = spi_id->driver_data; | 
|  | } | 
|  |  | 
|  | /* The SPI device is used to allocate dma memory */ | 
|  | if (!dev->coherent_dma_mask) { | 
|  | ret = dma_coerce_mask_and_coherent(dev, DMA_BIT_MASK(32)); | 
|  | if (ret) { | 
|  | dev_warn(dev, "Failed to set dma mask %d\n", ret); | 
|  | return ret; | 
|  | } | 
|  | } | 
|  |  | 
|  | epd = kzalloc(sizeof(*epd), GFP_KERNEL); | 
|  | if (!epd) | 
|  | return -ENOMEM; | 
|  |  | 
|  | drm = &epd->drm; | 
|  |  | 
|  | ret = devm_drm_dev_init(dev, drm, &repaper_driver); | 
|  | if (ret) { | 
|  | kfree(epd); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | drm_mode_config_init(drm); | 
|  | drm->mode_config.funcs = &repaper_mode_config_funcs; | 
|  |  | 
|  | epd->spi = spi; | 
|  |  | 
|  | epd->panel_on = devm_gpiod_get(dev, "panel-on", GPIOD_OUT_LOW); | 
|  | if (IS_ERR(epd->panel_on)) { | 
|  | ret = PTR_ERR(epd->panel_on); | 
|  | if (ret != -EPROBE_DEFER) | 
|  | DRM_DEV_ERROR(dev, "Failed to get gpio 'panel-on'\n"); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | epd->discharge = devm_gpiod_get(dev, "discharge", GPIOD_OUT_LOW); | 
|  | if (IS_ERR(epd->discharge)) { | 
|  | ret = PTR_ERR(epd->discharge); | 
|  | if (ret != -EPROBE_DEFER) | 
|  | DRM_DEV_ERROR(dev, "Failed to get gpio 'discharge'\n"); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | epd->reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); | 
|  | if (IS_ERR(epd->reset)) { | 
|  | ret = PTR_ERR(epd->reset); | 
|  | if (ret != -EPROBE_DEFER) | 
|  | DRM_DEV_ERROR(dev, "Failed to get gpio 'reset'\n"); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | epd->busy = devm_gpiod_get(dev, "busy", GPIOD_IN); | 
|  | if (IS_ERR(epd->busy)) { | 
|  | ret = PTR_ERR(epd->busy); | 
|  | if (ret != -EPROBE_DEFER) | 
|  | DRM_DEV_ERROR(dev, "Failed to get gpio 'busy'\n"); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | if (!device_property_read_string(dev, "pervasive,thermal-zone", | 
|  | &thermal_zone)) { | 
|  | epd->thermal = thermal_zone_get_zone_by_name(thermal_zone); | 
|  | if (IS_ERR(epd->thermal)) { | 
|  | DRM_DEV_ERROR(dev, "Failed to get thermal zone: %s\n", thermal_zone); | 
|  | return PTR_ERR(epd->thermal); | 
|  | } | 
|  | } | 
|  |  | 
|  | switch (model) { | 
|  | case E1144CS021: | 
|  | mode = &repaper_e1144cs021_mode; | 
|  | epd->channel_select = repaper_e1144cs021_cs; | 
|  | epd->stage_time = 480; | 
|  | epd->bytes_per_scan = 96 / 4; | 
|  | epd->middle_scan = true; /* data-scan-data */ | 
|  | epd->pre_border_byte = false; | 
|  | epd->border_byte = REPAPER_BORDER_BYTE_ZERO; | 
|  | break; | 
|  |  | 
|  | case E1190CS021: | 
|  | mode = &repaper_e1190cs021_mode; | 
|  | epd->channel_select = repaper_e1190cs021_cs; | 
|  | epd->stage_time = 480; | 
|  | epd->bytes_per_scan = 128 / 4 / 2; | 
|  | epd->middle_scan = false; /* scan-data-scan */ | 
|  | epd->pre_border_byte = false; | 
|  | epd->border_byte = REPAPER_BORDER_BYTE_SET; | 
|  | break; | 
|  |  | 
|  | case E2200CS021: | 
|  | mode = &repaper_e2200cs021_mode; | 
|  | epd->channel_select = repaper_e2200cs021_cs; | 
|  | epd->stage_time = 480; | 
|  | epd->bytes_per_scan = 96 / 4; | 
|  | epd->middle_scan = true; /* data-scan-data */ | 
|  | epd->pre_border_byte = true; | 
|  | epd->border_byte = REPAPER_BORDER_BYTE_NONE; | 
|  | break; | 
|  |  | 
|  | case E2271CS021: | 
|  | epd->border = devm_gpiod_get(dev, "border", GPIOD_OUT_LOW); | 
|  | if (IS_ERR(epd->border)) { | 
|  | ret = PTR_ERR(epd->border); | 
|  | if (ret != -EPROBE_DEFER) | 
|  | DRM_DEV_ERROR(dev, "Failed to get gpio 'border'\n"); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | mode = &repaper_e2271cs021_mode; | 
|  | epd->channel_select = repaper_e2271cs021_cs; | 
|  | epd->stage_time = 630; | 
|  | epd->bytes_per_scan = 176 / 4; | 
|  | epd->middle_scan = true; /* data-scan-data */ | 
|  | epd->pre_border_byte = true; | 
|  | epd->border_byte = REPAPER_BORDER_BYTE_NONE; | 
|  | break; | 
|  |  | 
|  | default: | 
|  | return -ENODEV; | 
|  | } | 
|  |  | 
|  | epd->width = mode->hdisplay; | 
|  | epd->height = mode->vdisplay; | 
|  | epd->factored_stage_time = epd->stage_time; | 
|  |  | 
|  | line_buffer_size = 2 * epd->width / 8 + epd->bytes_per_scan + 2; | 
|  | epd->line_buffer = devm_kzalloc(dev, line_buffer_size, GFP_KERNEL); | 
|  | if (!epd->line_buffer) | 
|  | return -ENOMEM; | 
|  |  | 
|  | epd->current_frame = devm_kzalloc(dev, epd->width * epd->height / 8, | 
|  | GFP_KERNEL); | 
|  | if (!epd->current_frame) | 
|  | return -ENOMEM; | 
|  |  | 
|  | ret = tinydrm_display_pipe_init(drm, &epd->pipe, &repaper_pipe_funcs, | 
|  | DRM_MODE_CONNECTOR_VIRTUAL, | 
|  | repaper_formats, | 
|  | ARRAY_SIZE(repaper_formats), mode, 0); | 
|  | if (ret) | 
|  | return ret; | 
|  |  | 
|  | drm_mode_config_reset(drm); | 
|  |  | 
|  | ret = drm_dev_register(drm, 0); | 
|  | if (ret) | 
|  | return ret; | 
|  |  | 
|  | spi_set_drvdata(spi, drm); | 
|  |  | 
|  | DRM_DEBUG_DRIVER("SPI speed: %uMHz\n", spi->max_speed_hz / 1000000); | 
|  |  | 
|  | drm_fbdev_generic_setup(drm, 0); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int repaper_remove(struct spi_device *spi) | 
|  | { | 
|  | struct drm_device *drm = spi_get_drvdata(spi); | 
|  |  | 
|  | drm_dev_unplug(drm); | 
|  | drm_atomic_helper_shutdown(drm); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void repaper_shutdown(struct spi_device *spi) | 
|  | { | 
|  | drm_atomic_helper_shutdown(spi_get_drvdata(spi)); | 
|  | } | 
|  |  | 
|  | static struct spi_driver repaper_spi_driver = { | 
|  | .driver = { | 
|  | .name = "repaper", | 
|  | .owner = THIS_MODULE, | 
|  | .of_match_table = repaper_of_match, | 
|  | }, | 
|  | .id_table = repaper_id, | 
|  | .probe = repaper_probe, | 
|  | .remove = repaper_remove, | 
|  | .shutdown = repaper_shutdown, | 
|  | }; | 
|  | module_spi_driver(repaper_spi_driver); | 
|  |  | 
|  | MODULE_DESCRIPTION("Pervasive Displays RePaper DRM driver"); | 
|  | MODULE_AUTHOR("Noralf Trønnes"); | 
|  | MODULE_LICENSE("GPL"); |