|  | /* | 
|  | * PXA168 ethernet driver. | 
|  | * Most of the code is derived from mv643xx ethernet driver. | 
|  | * | 
|  | * Copyright (C) 2010 Marvell International Ltd. | 
|  | *		Sachin Sanap <[email protected]> | 
|  | *		Zhangfei Gao <[email protected]> | 
|  | *		Philip Rakity <[email protected]> | 
|  | *		Mark Brown <[email protected]> | 
|  | * | 
|  | * This program is free software; you can redistribute it and/or | 
|  | * modify it under the terms of the GNU General Public License | 
|  | * as published by the Free Software Foundation; either version 2 | 
|  | * of the License, or (at your option) any later version. | 
|  | * | 
|  | * This program is distributed in the hope that it will be useful, | 
|  | * but WITHOUT ANY WARRANTY; without even the implied warranty of | 
|  | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the | 
|  | * GNU General Public License for more details. | 
|  | * | 
|  | * You should have received a copy of the GNU General Public License | 
|  | * along with this program; if not, write to the Free Software | 
|  | * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA  02111-1307, USA. | 
|  | */ | 
|  |  | 
|  | #include <linux/init.h> | 
|  | #include <linux/dma-mapping.h> | 
|  | #include <linux/in.h> | 
|  | #include <linux/ip.h> | 
|  | #include <linux/tcp.h> | 
|  | #include <linux/udp.h> | 
|  | #include <linux/etherdevice.h> | 
|  | #include <linux/bitops.h> | 
|  | #include <linux/delay.h> | 
|  | #include <linux/ethtool.h> | 
|  | #include <linux/platform_device.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/kernel.h> | 
|  | #include <linux/workqueue.h> | 
|  | #include <linux/clk.h> | 
|  | #include <linux/phy.h> | 
|  | #include <linux/io.h> | 
|  | #include <linux/types.h> | 
|  | #include <asm/pgtable.h> | 
|  | #include <asm/system.h> | 
|  | #include <asm/cacheflush.h> | 
|  | #include <linux/pxa168_eth.h> | 
|  |  | 
|  | #define DRIVER_NAME	"pxa168-eth" | 
|  | #define DRIVER_VERSION	"0.3" | 
|  |  | 
|  | /* | 
|  | * Registers | 
|  | */ | 
|  |  | 
|  | #define PHY_ADDRESS		0x0000 | 
|  | #define SMI			0x0010 | 
|  | #define PORT_CONFIG		0x0400 | 
|  | #define PORT_CONFIG_EXT		0x0408 | 
|  | #define PORT_COMMAND		0x0410 | 
|  | #define PORT_STATUS		0x0418 | 
|  | #define HTPR			0x0428 | 
|  | #define SDMA_CONFIG		0x0440 | 
|  | #define SDMA_CMD		0x0448 | 
|  | #define INT_CAUSE		0x0450 | 
|  | #define INT_W_CLEAR		0x0454 | 
|  | #define INT_MASK		0x0458 | 
|  | #define ETH_F_RX_DESC_0		0x0480 | 
|  | #define ETH_C_RX_DESC_0		0x04A0 | 
|  | #define ETH_C_TX_DESC_1		0x04E4 | 
|  |  | 
|  | /* smi register */ | 
|  | #define SMI_BUSY		(1 << 28)	/* 0 - Write, 1 - Read  */ | 
|  | #define SMI_R_VALID		(1 << 27)	/* 0 - Write, 1 - Read  */ | 
|  | #define SMI_OP_W		(0 << 26)	/* Write operation      */ | 
|  | #define SMI_OP_R		(1 << 26)	/* Read operation */ | 
|  |  | 
|  | #define PHY_WAIT_ITERATIONS	10 | 
|  |  | 
|  | #define PXA168_ETH_PHY_ADDR_DEFAULT	0 | 
|  | /* RX & TX descriptor command */ | 
|  | #define BUF_OWNED_BY_DMA	(1 << 31) | 
|  |  | 
|  | /* RX descriptor status */ | 
|  | #define RX_EN_INT		(1 << 23) | 
|  | #define RX_FIRST_DESC		(1 << 17) | 
|  | #define RX_LAST_DESC		(1 << 16) | 
|  | #define RX_ERROR		(1 << 15) | 
|  |  | 
|  | /* TX descriptor command */ | 
|  | #define TX_EN_INT		(1 << 23) | 
|  | #define TX_GEN_CRC		(1 << 22) | 
|  | #define TX_ZERO_PADDING		(1 << 18) | 
|  | #define TX_FIRST_DESC		(1 << 17) | 
|  | #define TX_LAST_DESC		(1 << 16) | 
|  | #define TX_ERROR		(1 << 15) | 
|  |  | 
|  | /* SDMA_CMD */ | 
|  | #define SDMA_CMD_AT		(1 << 31) | 
|  | #define SDMA_CMD_TXDL		(1 << 24) | 
|  | #define SDMA_CMD_TXDH		(1 << 23) | 
|  | #define SDMA_CMD_AR		(1 << 15) | 
|  | #define SDMA_CMD_ERD		(1 << 7) | 
|  |  | 
|  | /* Bit definitions of the Port Config Reg */ | 
|  | #define PCR_HS			(1 << 12) | 
|  | #define PCR_EN			(1 << 7) | 
|  | #define PCR_PM			(1 << 0) | 
|  |  | 
|  | /* Bit definitions of the Port Config Extend Reg */ | 
|  | #define PCXR_2BSM		(1 << 28) | 
|  | #define PCXR_DSCP_EN		(1 << 21) | 
|  | #define PCXR_MFL_1518		(0 << 14) | 
|  | #define PCXR_MFL_1536		(1 << 14) | 
|  | #define PCXR_MFL_2048		(2 << 14) | 
|  | #define PCXR_MFL_64K		(3 << 14) | 
|  | #define PCXR_FLP		(1 << 11) | 
|  | #define PCXR_PRIO_TX_OFF	3 | 
|  | #define PCXR_TX_HIGH_PRI	(7 << PCXR_PRIO_TX_OFF) | 
|  |  | 
|  | /* Bit definitions of the SDMA Config Reg */ | 
|  | #define SDCR_BSZ_OFF		12 | 
|  | #define SDCR_BSZ8		(3 << SDCR_BSZ_OFF) | 
|  | #define SDCR_BSZ4		(2 << SDCR_BSZ_OFF) | 
|  | #define SDCR_BSZ2		(1 << SDCR_BSZ_OFF) | 
|  | #define SDCR_BSZ1		(0 << SDCR_BSZ_OFF) | 
|  | #define SDCR_BLMR		(1 << 6) | 
|  | #define SDCR_BLMT		(1 << 7) | 
|  | #define SDCR_RIFB		(1 << 9) | 
|  | #define SDCR_RC_OFF		2 | 
|  | #define SDCR_RC_MAX_RETRANS	(0xf << SDCR_RC_OFF) | 
|  |  | 
|  | /* | 
|  | * Bit definitions of the Interrupt Cause Reg | 
|  | * and Interrupt MASK Reg is the same | 
|  | */ | 
|  | #define ICR_RXBUF		(1 << 0) | 
|  | #define ICR_TXBUF_H		(1 << 2) | 
|  | #define ICR_TXBUF_L		(1 << 3) | 
|  | #define ICR_TXEND_H		(1 << 6) | 
|  | #define ICR_TXEND_L		(1 << 7) | 
|  | #define ICR_RXERR		(1 << 8) | 
|  | #define ICR_TXERR_H		(1 << 10) | 
|  | #define ICR_TXERR_L		(1 << 11) | 
|  | #define ICR_TX_UDR		(1 << 13) | 
|  | #define ICR_MII_CH		(1 << 28) | 
|  |  | 
|  | #define ALL_INTS (ICR_TXBUF_H  | ICR_TXBUF_L  | ICR_TX_UDR |\ | 
|  | ICR_TXERR_H  | ICR_TXERR_L |\ | 
|  | ICR_TXEND_H  | ICR_TXEND_L |\ | 
|  | ICR_RXBUF | ICR_RXERR  | ICR_MII_CH) | 
|  |  | 
|  | #define ETH_HW_IP_ALIGN		2	/* hw aligns IP header */ | 
|  |  | 
|  | #define NUM_RX_DESCS		64 | 
|  | #define NUM_TX_DESCS		64 | 
|  |  | 
|  | #define HASH_ADD		0 | 
|  | #define HASH_DELETE		1 | 
|  | #define HASH_ADDR_TABLE_SIZE	0x4000	/* 16K (1/2K address - PCR_HS == 1) */ | 
|  | #define HOP_NUMBER		12 | 
|  |  | 
|  | /* Bit definitions for Port status */ | 
|  | #define PORT_SPEED_100		(1 << 0) | 
|  | #define FULL_DUPLEX		(1 << 1) | 
|  | #define FLOW_CONTROL_ENABLED	(1 << 2) | 
|  | #define LINK_UP			(1 << 3) | 
|  |  | 
|  | /* Bit definitions for work to be done */ | 
|  | #define WORK_LINK		(1 << 0) | 
|  | #define WORK_TX_DONE		(1 << 1) | 
|  |  | 
|  | /* | 
|  | * Misc definitions. | 
|  | */ | 
|  | #define SKB_DMA_REALIGN		((PAGE_SIZE - NET_SKB_PAD) % SMP_CACHE_BYTES) | 
|  |  | 
|  | struct rx_desc { | 
|  | u32 cmd_sts;		/* Descriptor command status            */ | 
|  | u16 byte_cnt;		/* Descriptor buffer byte count         */ | 
|  | u16 buf_size;		/* Buffer size                          */ | 
|  | u32 buf_ptr;		/* Descriptor buffer pointer            */ | 
|  | u32 next_desc_ptr;	/* Next descriptor pointer              */ | 
|  | }; | 
|  |  | 
|  | struct tx_desc { | 
|  | u32 cmd_sts;		/* Command/status field                 */ | 
|  | u16 reserved; | 
|  | u16 byte_cnt;		/* buffer byte count                    */ | 
|  | u32 buf_ptr;		/* pointer to buffer for this descriptor */ | 
|  | u32 next_desc_ptr;	/* Pointer to next descriptor           */ | 
|  | }; | 
|  |  | 
|  | struct pxa168_eth_private { | 
|  | int port_num;		/* User Ethernet port number    */ | 
|  |  | 
|  | int rx_resource_err;	/* Rx ring resource error flag */ | 
|  |  | 
|  | /* Next available and first returning Rx resource */ | 
|  | int rx_curr_desc_q, rx_used_desc_q; | 
|  |  | 
|  | /* Next available and first returning Tx resource */ | 
|  | int tx_curr_desc_q, tx_used_desc_q; | 
|  |  | 
|  | struct rx_desc *p_rx_desc_area; | 
|  | dma_addr_t rx_desc_dma; | 
|  | int rx_desc_area_size; | 
|  | struct sk_buff **rx_skb; | 
|  |  | 
|  | struct tx_desc *p_tx_desc_area; | 
|  | dma_addr_t tx_desc_dma; | 
|  | int tx_desc_area_size; | 
|  | struct sk_buff **tx_skb; | 
|  |  | 
|  | struct work_struct tx_timeout_task; | 
|  |  | 
|  | struct net_device *dev; | 
|  | struct napi_struct napi; | 
|  | u8 work_todo; | 
|  | int skb_size; | 
|  |  | 
|  | struct net_device_stats stats; | 
|  | /* Size of Tx Ring per queue */ | 
|  | int tx_ring_size; | 
|  | /* Number of tx descriptors in use */ | 
|  | int tx_desc_count; | 
|  | /* Size of Rx Ring per queue */ | 
|  | int rx_ring_size; | 
|  | /* Number of rx descriptors in use */ | 
|  | int rx_desc_count; | 
|  |  | 
|  | /* | 
|  | * Used in case RX Ring is empty, which can occur when | 
|  | * system does not have resources (skb's) | 
|  | */ | 
|  | struct timer_list timeout; | 
|  | struct mii_bus *smi_bus; | 
|  | struct phy_device *phy; | 
|  |  | 
|  | /* clock */ | 
|  | struct clk *clk; | 
|  | struct pxa168_eth_platform_data *pd; | 
|  | /* | 
|  | * Ethernet controller base address. | 
|  | */ | 
|  | void __iomem *base; | 
|  |  | 
|  | /* Pointer to the hardware address filter table */ | 
|  | void *htpr; | 
|  | dma_addr_t htpr_dma; | 
|  | }; | 
|  |  | 
|  | struct addr_table_entry { | 
|  | __le32 lo; | 
|  | __le32 hi; | 
|  | }; | 
|  |  | 
|  | /* Bit fields of a Hash Table Entry */ | 
|  | enum hash_table_entry { | 
|  | HASH_ENTRY_VALID = 1, | 
|  | SKIP = 2, | 
|  | HASH_ENTRY_RECEIVE_DISCARD = 4, | 
|  | HASH_ENTRY_RECEIVE_DISCARD_BIT = 2 | 
|  | }; | 
|  |  | 
|  | static int pxa168_get_settings(struct net_device *dev, struct ethtool_cmd *cmd); | 
|  | static int pxa168_set_settings(struct net_device *dev, struct ethtool_cmd *cmd); | 
|  | static int pxa168_init_hw(struct pxa168_eth_private *pep); | 
|  | static void eth_port_reset(struct net_device *dev); | 
|  | static void eth_port_start(struct net_device *dev); | 
|  | static int pxa168_eth_open(struct net_device *dev); | 
|  | static int pxa168_eth_stop(struct net_device *dev); | 
|  | static int ethernet_phy_setup(struct net_device *dev); | 
|  |  | 
|  | static inline u32 rdl(struct pxa168_eth_private *pep, int offset) | 
|  | { | 
|  | return readl(pep->base + offset); | 
|  | } | 
|  |  | 
|  | static inline void wrl(struct pxa168_eth_private *pep, int offset, u32 data) | 
|  | { | 
|  | writel(data, pep->base + offset); | 
|  | } | 
|  |  | 
|  | static void abort_dma(struct pxa168_eth_private *pep) | 
|  | { | 
|  | int delay; | 
|  | int max_retries = 40; | 
|  |  | 
|  | do { | 
|  | wrl(pep, SDMA_CMD, SDMA_CMD_AR | SDMA_CMD_AT); | 
|  | udelay(100); | 
|  |  | 
|  | delay = 10; | 
|  | while ((rdl(pep, SDMA_CMD) & (SDMA_CMD_AR | SDMA_CMD_AT)) | 
|  | && delay-- > 0) { | 
|  | udelay(10); | 
|  | } | 
|  | } while (max_retries-- > 0 && delay <= 0); | 
|  |  | 
|  | if (max_retries <= 0) | 
|  | printk(KERN_ERR "%s : DMA Stuck\n", __func__); | 
|  | } | 
|  |  | 
|  | static int ethernet_phy_get(struct pxa168_eth_private *pep) | 
|  | { | 
|  | unsigned int reg_data; | 
|  |  | 
|  | reg_data = rdl(pep, PHY_ADDRESS); | 
|  |  | 
|  | return (reg_data >> (5 * pep->port_num)) & 0x1f; | 
|  | } | 
|  |  | 
|  | static void ethernet_phy_set_addr(struct pxa168_eth_private *pep, int phy_addr) | 
|  | { | 
|  | u32 reg_data; | 
|  | int addr_shift = 5 * pep->port_num; | 
|  |  | 
|  | reg_data = rdl(pep, PHY_ADDRESS); | 
|  | reg_data &= ~(0x1f << addr_shift); | 
|  | reg_data |= (phy_addr & 0x1f) << addr_shift; | 
|  | wrl(pep, PHY_ADDRESS, reg_data); | 
|  | } | 
|  |  | 
|  | static void ethernet_phy_reset(struct pxa168_eth_private *pep) | 
|  | { | 
|  | int data; | 
|  |  | 
|  | data = phy_read(pep->phy, MII_BMCR); | 
|  | if (data < 0) | 
|  | return; | 
|  |  | 
|  | data |= BMCR_RESET; | 
|  | if (phy_write(pep->phy, MII_BMCR, data) < 0) | 
|  | return; | 
|  |  | 
|  | do { | 
|  | data = phy_read(pep->phy, MII_BMCR); | 
|  | } while (data >= 0 && data & BMCR_RESET); | 
|  | } | 
|  |  | 
|  | static void rxq_refill(struct net_device *dev) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  | struct sk_buff *skb; | 
|  | struct rx_desc *p_used_rx_desc; | 
|  | int used_rx_desc; | 
|  |  | 
|  | while (pep->rx_desc_count < pep->rx_ring_size) { | 
|  | int size; | 
|  |  | 
|  | skb = dev_alloc_skb(pep->skb_size); | 
|  | if (!skb) | 
|  | break; | 
|  | if (SKB_DMA_REALIGN) | 
|  | skb_reserve(skb, SKB_DMA_REALIGN); | 
|  | pep->rx_desc_count++; | 
|  | /* Get 'used' Rx descriptor */ | 
|  | used_rx_desc = pep->rx_used_desc_q; | 
|  | p_used_rx_desc = &pep->p_rx_desc_area[used_rx_desc]; | 
|  | size = skb->end - skb->data; | 
|  | p_used_rx_desc->buf_ptr = dma_map_single(NULL, | 
|  | skb->data, | 
|  | size, | 
|  | DMA_FROM_DEVICE); | 
|  | p_used_rx_desc->buf_size = size; | 
|  | pep->rx_skb[used_rx_desc] = skb; | 
|  |  | 
|  | /* Return the descriptor to DMA ownership */ | 
|  | wmb(); | 
|  | p_used_rx_desc->cmd_sts = BUF_OWNED_BY_DMA | RX_EN_INT; | 
|  | wmb(); | 
|  |  | 
|  | /* Move the used descriptor pointer to the next descriptor */ | 
|  | pep->rx_used_desc_q = (used_rx_desc + 1) % pep->rx_ring_size; | 
|  |  | 
|  | /* Any Rx return cancels the Rx resource error status */ | 
|  | pep->rx_resource_err = 0; | 
|  |  | 
|  | skb_reserve(skb, ETH_HW_IP_ALIGN); | 
|  | } | 
|  |  | 
|  | /* | 
|  | * If RX ring is empty of SKB, set a timer to try allocating | 
|  | * again at a later time. | 
|  | */ | 
|  | if (pep->rx_desc_count == 0) { | 
|  | pep->timeout.expires = jiffies + (HZ / 10); | 
|  | add_timer(&pep->timeout); | 
|  | } | 
|  | } | 
|  |  | 
|  | static inline void rxq_refill_timer_wrapper(unsigned long data) | 
|  | { | 
|  | struct pxa168_eth_private *pep = (void *)data; | 
|  | napi_schedule(&pep->napi); | 
|  | } | 
|  |  | 
|  | static inline u8 flip_8_bits(u8 x) | 
|  | { | 
|  | return (((x) & 0x01) << 3) | (((x) & 0x02) << 1) | 
|  | | (((x) & 0x04) >> 1) | (((x) & 0x08) >> 3) | 
|  | | (((x) & 0x10) << 3) | (((x) & 0x20) << 1) | 
|  | | (((x) & 0x40) >> 1) | (((x) & 0x80) >> 3); | 
|  | } | 
|  |  | 
|  | static void nibble_swap_every_byte(unsigned char *mac_addr) | 
|  | { | 
|  | int i; | 
|  | for (i = 0; i < ETH_ALEN; i++) { | 
|  | mac_addr[i] = ((mac_addr[i] & 0x0f) << 4) | | 
|  | ((mac_addr[i] & 0xf0) >> 4); | 
|  | } | 
|  | } | 
|  |  | 
|  | static void inverse_every_nibble(unsigned char *mac_addr) | 
|  | { | 
|  | int i; | 
|  | for (i = 0; i < ETH_ALEN; i++) | 
|  | mac_addr[i] = flip_8_bits(mac_addr[i]); | 
|  | } | 
|  |  | 
|  | /* | 
|  | * ---------------------------------------------------------------------------- | 
|  | * This function will calculate the hash function of the address. | 
|  | * Inputs | 
|  | * mac_addr_orig    - MAC address. | 
|  | * Outputs | 
|  | * return the calculated entry. | 
|  | */ | 
|  | static u32 hash_function(unsigned char *mac_addr_orig) | 
|  | { | 
|  | u32 hash_result; | 
|  | u32 addr0; | 
|  | u32 addr1; | 
|  | u32 addr2; | 
|  | u32 addr3; | 
|  | unsigned char mac_addr[ETH_ALEN]; | 
|  |  | 
|  | /* Make a copy of MAC address since we are going to performe bit | 
|  | * operations on it | 
|  | */ | 
|  | memcpy(mac_addr, mac_addr_orig, ETH_ALEN); | 
|  |  | 
|  | nibble_swap_every_byte(mac_addr); | 
|  | inverse_every_nibble(mac_addr); | 
|  |  | 
|  | addr0 = (mac_addr[5] >> 2) & 0x3f; | 
|  | addr1 = (mac_addr[5] & 0x03) | (((mac_addr[4] & 0x7f)) << 2); | 
|  | addr2 = ((mac_addr[4] & 0x80) >> 7) | mac_addr[3] << 1; | 
|  | addr3 = (mac_addr[2] & 0xff) | ((mac_addr[1] & 1) << 8); | 
|  |  | 
|  | hash_result = (addr0 << 9) | (addr1 ^ addr2 ^ addr3); | 
|  | hash_result = hash_result & 0x07ff; | 
|  | return hash_result; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * ---------------------------------------------------------------------------- | 
|  | * This function will add/del an entry to the address table. | 
|  | * Inputs | 
|  | * pep - ETHERNET . | 
|  | * mac_addr - MAC address. | 
|  | * skip - if 1, skip this address.Used in case of deleting an entry which is a | 
|  | *	  part of chain in the hash table.We can't just delete the entry since | 
|  | *	  that will break the chain.We need to defragment the tables time to | 
|  | *	  time. | 
|  | * rd   - 0 Discard packet upon match. | 
|  | *	- 1 Receive packet upon match. | 
|  | * Outputs | 
|  | * address table entry is added/deleted. | 
|  | * 0 if success. | 
|  | * -ENOSPC if table full | 
|  | */ | 
|  | static int add_del_hash_entry(struct pxa168_eth_private *pep, | 
|  | unsigned char *mac_addr, | 
|  | u32 rd, u32 skip, int del) | 
|  | { | 
|  | struct addr_table_entry *entry, *start; | 
|  | u32 new_high; | 
|  | u32 new_low; | 
|  | u32 i; | 
|  |  | 
|  | new_low = (((mac_addr[1] >> 4) & 0xf) << 15) | 
|  | | (((mac_addr[1] >> 0) & 0xf) << 11) | 
|  | | (((mac_addr[0] >> 4) & 0xf) << 7) | 
|  | | (((mac_addr[0] >> 0) & 0xf) << 3) | 
|  | | (((mac_addr[3] >> 4) & 0x1) << 31) | 
|  | | (((mac_addr[3] >> 0) & 0xf) << 27) | 
|  | | (((mac_addr[2] >> 4) & 0xf) << 23) | 
|  | | (((mac_addr[2] >> 0) & 0xf) << 19) | 
|  | | (skip << SKIP) | (rd << HASH_ENTRY_RECEIVE_DISCARD_BIT) | 
|  | | HASH_ENTRY_VALID; | 
|  |  | 
|  | new_high = (((mac_addr[5] >> 4) & 0xf) << 15) | 
|  | | (((mac_addr[5] >> 0) & 0xf) << 11) | 
|  | | (((mac_addr[4] >> 4) & 0xf) << 7) | 
|  | | (((mac_addr[4] >> 0) & 0xf) << 3) | 
|  | | (((mac_addr[3] >> 5) & 0x7) << 0); | 
|  |  | 
|  | /* | 
|  | * Pick the appropriate table, start scanning for free/reusable | 
|  | * entries at the index obtained by hashing the specified MAC address | 
|  | */ | 
|  | start = (struct addr_table_entry *)(pep->htpr); | 
|  | entry = start + hash_function(mac_addr); | 
|  | for (i = 0; i < HOP_NUMBER; i++) { | 
|  | if (!(le32_to_cpu(entry->lo) & HASH_ENTRY_VALID)) { | 
|  | break; | 
|  | } else { | 
|  | /* if same address put in same position */ | 
|  | if (((le32_to_cpu(entry->lo) & 0xfffffff8) == | 
|  | (new_low & 0xfffffff8)) && | 
|  | (le32_to_cpu(entry->hi) == new_high)) { | 
|  | break; | 
|  | } | 
|  | } | 
|  | if (entry == start + 0x7ff) | 
|  | entry = start; | 
|  | else | 
|  | entry++; | 
|  | } | 
|  |  | 
|  | if (((le32_to_cpu(entry->lo) & 0xfffffff8) != (new_low & 0xfffffff8)) && | 
|  | (le32_to_cpu(entry->hi) != new_high) && del) | 
|  | return 0; | 
|  |  | 
|  | if (i == HOP_NUMBER) { | 
|  | if (!del) { | 
|  | printk(KERN_INFO "%s: table section is full, need to " | 
|  | "move to 16kB implementation?\n", | 
|  | __FILE__); | 
|  | return -ENOSPC; | 
|  | } else | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Update the selected entry | 
|  | */ | 
|  | if (del) { | 
|  | entry->hi = 0; | 
|  | entry->lo = 0; | 
|  | } else { | 
|  | entry->hi = cpu_to_le32(new_high); | 
|  | entry->lo = cpu_to_le32(new_low); | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * ---------------------------------------------------------------------------- | 
|  | *  Create an addressTable entry from MAC address info | 
|  | *  found in the specifed net_device struct | 
|  | * | 
|  | *  Input : pointer to ethernet interface network device structure | 
|  | *  Output : N/A | 
|  | */ | 
|  | static void update_hash_table_mac_address(struct pxa168_eth_private *pep, | 
|  | unsigned char *oaddr, | 
|  | unsigned char *addr) | 
|  | { | 
|  | /* Delete old entry */ | 
|  | if (oaddr) | 
|  | add_del_hash_entry(pep, oaddr, 1, 0, HASH_DELETE); | 
|  | /* Add new entry */ | 
|  | add_del_hash_entry(pep, addr, 1, 0, HASH_ADD); | 
|  | } | 
|  |  | 
|  | static int init_hash_table(struct pxa168_eth_private *pep) | 
|  | { | 
|  | /* | 
|  | * Hardware expects CPU to build a hash table based on a predefined | 
|  | * hash function and populate it based on hardware address. The | 
|  | * location of the hash table is identified by 32-bit pointer stored | 
|  | * in HTPR internal register. Two possible sizes exists for the hash | 
|  | * table 8kB (256kB of DRAM required (4 x 64 kB banks)) and 1/2kB | 
|  | * (16kB of DRAM required (4 x 4 kB banks)).We currently only support | 
|  | * 1/2kB. | 
|  | */ | 
|  | /* TODO: Add support for 8kB hash table and alternative hash | 
|  | * function.Driver can dynamically switch to them if the 1/2kB hash | 
|  | * table is full. | 
|  | */ | 
|  | if (pep->htpr == NULL) { | 
|  | pep->htpr = dma_alloc_coherent(pep->dev->dev.parent, | 
|  | HASH_ADDR_TABLE_SIZE, | 
|  | &pep->htpr_dma, GFP_KERNEL); | 
|  | if (pep->htpr == NULL) | 
|  | return -ENOMEM; | 
|  | } | 
|  | memset(pep->htpr, 0, HASH_ADDR_TABLE_SIZE); | 
|  | wrl(pep, HTPR, pep->htpr_dma); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void pxa168_eth_set_rx_mode(struct net_device *dev) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  | struct netdev_hw_addr *ha; | 
|  | u32 val; | 
|  |  | 
|  | val = rdl(pep, PORT_CONFIG); | 
|  | if (dev->flags & IFF_PROMISC) | 
|  | val |= PCR_PM; | 
|  | else | 
|  | val &= ~PCR_PM; | 
|  | wrl(pep, PORT_CONFIG, val); | 
|  |  | 
|  | /* | 
|  | * Remove the old list of MAC address and add dev->addr | 
|  | * and multicast address. | 
|  | */ | 
|  | memset(pep->htpr, 0, HASH_ADDR_TABLE_SIZE); | 
|  | update_hash_table_mac_address(pep, NULL, dev->dev_addr); | 
|  |  | 
|  | netdev_for_each_mc_addr(ha, dev) | 
|  | update_hash_table_mac_address(pep, NULL, ha->addr); | 
|  | } | 
|  |  | 
|  | static int pxa168_eth_set_mac_address(struct net_device *dev, void *addr) | 
|  | { | 
|  | struct sockaddr *sa = addr; | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  | unsigned char oldMac[ETH_ALEN]; | 
|  |  | 
|  | if (!is_valid_ether_addr(sa->sa_data)) | 
|  | return -EINVAL; | 
|  | memcpy(oldMac, dev->dev_addr, ETH_ALEN); | 
|  | memcpy(dev->dev_addr, sa->sa_data, ETH_ALEN); | 
|  | netif_addr_lock_bh(dev); | 
|  | update_hash_table_mac_address(pep, oldMac, dev->dev_addr); | 
|  | netif_addr_unlock_bh(dev); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void eth_port_start(struct net_device *dev) | 
|  | { | 
|  | unsigned int val = 0; | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  | int tx_curr_desc, rx_curr_desc; | 
|  |  | 
|  | /* Perform PHY reset, if there is a PHY. */ | 
|  | if (pep->phy != NULL) { | 
|  | struct ethtool_cmd cmd; | 
|  |  | 
|  | pxa168_get_settings(pep->dev, &cmd); | 
|  | ethernet_phy_reset(pep); | 
|  | pxa168_set_settings(pep->dev, &cmd); | 
|  | } | 
|  |  | 
|  | /* Assignment of Tx CTRP of given queue */ | 
|  | tx_curr_desc = pep->tx_curr_desc_q; | 
|  | wrl(pep, ETH_C_TX_DESC_1, | 
|  | (u32) (pep->tx_desc_dma + tx_curr_desc * sizeof(struct tx_desc))); | 
|  |  | 
|  | /* Assignment of Rx CRDP of given queue */ | 
|  | rx_curr_desc = pep->rx_curr_desc_q; | 
|  | wrl(pep, ETH_C_RX_DESC_0, | 
|  | (u32) (pep->rx_desc_dma + rx_curr_desc * sizeof(struct rx_desc))); | 
|  |  | 
|  | wrl(pep, ETH_F_RX_DESC_0, | 
|  | (u32) (pep->rx_desc_dma + rx_curr_desc * sizeof(struct rx_desc))); | 
|  |  | 
|  | /* Clear all interrupts */ | 
|  | wrl(pep, INT_CAUSE, 0); | 
|  |  | 
|  | /* Enable all interrupts for receive, transmit and error. */ | 
|  | wrl(pep, INT_MASK, ALL_INTS); | 
|  |  | 
|  | val = rdl(pep, PORT_CONFIG); | 
|  | val |= PCR_EN; | 
|  | wrl(pep, PORT_CONFIG, val); | 
|  |  | 
|  | /* Start RX DMA engine */ | 
|  | val = rdl(pep, SDMA_CMD); | 
|  | val |= SDMA_CMD_ERD; | 
|  | wrl(pep, SDMA_CMD, val); | 
|  | } | 
|  |  | 
|  | static void eth_port_reset(struct net_device *dev) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  | unsigned int val = 0; | 
|  |  | 
|  | /* Stop all interrupts for receive, transmit and error. */ | 
|  | wrl(pep, INT_MASK, 0); | 
|  |  | 
|  | /* Clear all interrupts */ | 
|  | wrl(pep, INT_CAUSE, 0); | 
|  |  | 
|  | /* Stop RX DMA */ | 
|  | val = rdl(pep, SDMA_CMD); | 
|  | val &= ~SDMA_CMD_ERD;	/* abort dma command */ | 
|  |  | 
|  | /* Abort any transmit and receive operations and put DMA | 
|  | * in idle state. | 
|  | */ | 
|  | abort_dma(pep); | 
|  |  | 
|  | /* Disable port */ | 
|  | val = rdl(pep, PORT_CONFIG); | 
|  | val &= ~PCR_EN; | 
|  | wrl(pep, PORT_CONFIG, val); | 
|  | } | 
|  |  | 
|  | /* | 
|  | * txq_reclaim - Free the tx desc data for completed descriptors | 
|  | * If force is non-zero, frees uncompleted descriptors as well | 
|  | */ | 
|  | static int txq_reclaim(struct net_device *dev, int force) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  | struct tx_desc *desc; | 
|  | u32 cmd_sts; | 
|  | struct sk_buff *skb; | 
|  | int tx_index; | 
|  | dma_addr_t addr; | 
|  | int count; | 
|  | int released = 0; | 
|  |  | 
|  | netif_tx_lock(dev); | 
|  |  | 
|  | pep->work_todo &= ~WORK_TX_DONE; | 
|  | while (pep->tx_desc_count > 0) { | 
|  | tx_index = pep->tx_used_desc_q; | 
|  | desc = &pep->p_tx_desc_area[tx_index]; | 
|  | cmd_sts = desc->cmd_sts; | 
|  | if (!force && (cmd_sts & BUF_OWNED_BY_DMA)) { | 
|  | if (released > 0) { | 
|  | goto txq_reclaim_end; | 
|  | } else { | 
|  | released = -1; | 
|  | goto txq_reclaim_end; | 
|  | } | 
|  | } | 
|  | pep->tx_used_desc_q = (tx_index + 1) % pep->tx_ring_size; | 
|  | pep->tx_desc_count--; | 
|  | addr = desc->buf_ptr; | 
|  | count = desc->byte_cnt; | 
|  | skb = pep->tx_skb[tx_index]; | 
|  | if (skb) | 
|  | pep->tx_skb[tx_index] = NULL; | 
|  |  | 
|  | if (cmd_sts & TX_ERROR) { | 
|  | if (net_ratelimit()) | 
|  | printk(KERN_ERR "%s: Error in TX\n", dev->name); | 
|  | dev->stats.tx_errors++; | 
|  | } | 
|  | dma_unmap_single(NULL, addr, count, DMA_TO_DEVICE); | 
|  | if (skb) | 
|  | dev_kfree_skb_irq(skb); | 
|  | released++; | 
|  | } | 
|  | txq_reclaim_end: | 
|  | netif_tx_unlock(dev); | 
|  | return released; | 
|  | } | 
|  |  | 
|  | static void pxa168_eth_tx_timeout(struct net_device *dev) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  |  | 
|  | printk(KERN_INFO "%s: TX timeout  desc_count %d\n", | 
|  | dev->name, pep->tx_desc_count); | 
|  |  | 
|  | schedule_work(&pep->tx_timeout_task); | 
|  | } | 
|  |  | 
|  | static void pxa168_eth_tx_timeout_task(struct work_struct *work) | 
|  | { | 
|  | struct pxa168_eth_private *pep = container_of(work, | 
|  | struct pxa168_eth_private, | 
|  | tx_timeout_task); | 
|  | struct net_device *dev = pep->dev; | 
|  | pxa168_eth_stop(dev); | 
|  | pxa168_eth_open(dev); | 
|  | } | 
|  |  | 
|  | static int rxq_process(struct net_device *dev, int budget) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  | struct net_device_stats *stats = &dev->stats; | 
|  | unsigned int received_packets = 0; | 
|  | struct sk_buff *skb; | 
|  |  | 
|  | while (budget-- > 0) { | 
|  | int rx_next_curr_desc, rx_curr_desc, rx_used_desc; | 
|  | struct rx_desc *rx_desc; | 
|  | unsigned int cmd_sts; | 
|  |  | 
|  | /* Do not process Rx ring in case of Rx ring resource error */ | 
|  | if (pep->rx_resource_err) | 
|  | break; | 
|  | rx_curr_desc = pep->rx_curr_desc_q; | 
|  | rx_used_desc = pep->rx_used_desc_q; | 
|  | rx_desc = &pep->p_rx_desc_area[rx_curr_desc]; | 
|  | cmd_sts = rx_desc->cmd_sts; | 
|  | rmb(); | 
|  | if (cmd_sts & (BUF_OWNED_BY_DMA)) | 
|  | break; | 
|  | skb = pep->rx_skb[rx_curr_desc]; | 
|  | pep->rx_skb[rx_curr_desc] = NULL; | 
|  |  | 
|  | rx_next_curr_desc = (rx_curr_desc + 1) % pep->rx_ring_size; | 
|  | pep->rx_curr_desc_q = rx_next_curr_desc; | 
|  |  | 
|  | /* Rx descriptors exhausted. */ | 
|  | /* Set the Rx ring resource error flag */ | 
|  | if (rx_next_curr_desc == rx_used_desc) | 
|  | pep->rx_resource_err = 1; | 
|  | pep->rx_desc_count--; | 
|  | dma_unmap_single(NULL, rx_desc->buf_ptr, | 
|  | rx_desc->buf_size, | 
|  | DMA_FROM_DEVICE); | 
|  | received_packets++; | 
|  | /* | 
|  | * Update statistics. | 
|  | * Note byte count includes 4 byte CRC count | 
|  | */ | 
|  | stats->rx_packets++; | 
|  | stats->rx_bytes += rx_desc->byte_cnt; | 
|  | /* | 
|  | * In case received a packet without first / last bits on OR | 
|  | * the error summary bit is on, the packets needs to be droped. | 
|  | */ | 
|  | if (((cmd_sts & (RX_FIRST_DESC | RX_LAST_DESC)) != | 
|  | (RX_FIRST_DESC | RX_LAST_DESC)) | 
|  | || (cmd_sts & RX_ERROR)) { | 
|  |  | 
|  | stats->rx_dropped++; | 
|  | if ((cmd_sts & (RX_FIRST_DESC | RX_LAST_DESC)) != | 
|  | (RX_FIRST_DESC | RX_LAST_DESC)) { | 
|  | if (net_ratelimit()) | 
|  | printk(KERN_ERR | 
|  | "%s: Rx pkt on multiple desc\n", | 
|  | dev->name); | 
|  | } | 
|  | if (cmd_sts & RX_ERROR) | 
|  | stats->rx_errors++; | 
|  | dev_kfree_skb_irq(skb); | 
|  | } else { | 
|  | /* | 
|  | * The -4 is for the CRC in the trailer of the | 
|  | * received packet | 
|  | */ | 
|  | skb_put(skb, rx_desc->byte_cnt - 4); | 
|  | skb->protocol = eth_type_trans(skb, dev); | 
|  | netif_receive_skb(skb); | 
|  | } | 
|  | } | 
|  | /* Fill RX ring with skb's */ | 
|  | rxq_refill(dev); | 
|  | return received_packets; | 
|  | } | 
|  |  | 
|  | static int pxa168_eth_collect_events(struct pxa168_eth_private *pep, | 
|  | struct net_device *dev) | 
|  | { | 
|  | u32 icr; | 
|  | int ret = 0; | 
|  |  | 
|  | icr = rdl(pep, INT_CAUSE); | 
|  | if (icr == 0) | 
|  | return IRQ_NONE; | 
|  |  | 
|  | wrl(pep, INT_CAUSE, ~icr); | 
|  | if (icr & (ICR_TXBUF_H | ICR_TXBUF_L)) { | 
|  | pep->work_todo |= WORK_TX_DONE; | 
|  | ret = 1; | 
|  | } | 
|  | if (icr & ICR_RXBUF) | 
|  | ret = 1; | 
|  | if (icr & ICR_MII_CH) { | 
|  | pep->work_todo |= WORK_LINK; | 
|  | ret = 1; | 
|  | } | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static void handle_link_event(struct pxa168_eth_private *pep) | 
|  | { | 
|  | struct net_device *dev = pep->dev; | 
|  | u32 port_status; | 
|  | int speed; | 
|  | int duplex; | 
|  | int fc; | 
|  |  | 
|  | port_status = rdl(pep, PORT_STATUS); | 
|  | if (!(port_status & LINK_UP)) { | 
|  | if (netif_carrier_ok(dev)) { | 
|  | printk(KERN_INFO "%s: link down\n", dev->name); | 
|  | netif_carrier_off(dev); | 
|  | txq_reclaim(dev, 1); | 
|  | } | 
|  | return; | 
|  | } | 
|  | if (port_status & PORT_SPEED_100) | 
|  | speed = 100; | 
|  | else | 
|  | speed = 10; | 
|  |  | 
|  | duplex = (port_status & FULL_DUPLEX) ? 1 : 0; | 
|  | fc = (port_status & FLOW_CONTROL_ENABLED) ? 1 : 0; | 
|  | printk(KERN_INFO "%s: link up, %d Mb/s, %s duplex, " | 
|  | "flow control %sabled\n", dev->name, | 
|  | speed, duplex ? "full" : "half", fc ? "en" : "dis"); | 
|  | if (!netif_carrier_ok(dev)) | 
|  | netif_carrier_on(dev); | 
|  | } | 
|  |  | 
|  | static irqreturn_t pxa168_eth_int_handler(int irq, void *dev_id) | 
|  | { | 
|  | struct net_device *dev = (struct net_device *)dev_id; | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  |  | 
|  | if (unlikely(!pxa168_eth_collect_events(pep, dev))) | 
|  | return IRQ_NONE; | 
|  | /* Disable interrupts */ | 
|  | wrl(pep, INT_MASK, 0); | 
|  | napi_schedule(&pep->napi); | 
|  | return IRQ_HANDLED; | 
|  | } | 
|  |  | 
|  | static void pxa168_eth_recalc_skb_size(struct pxa168_eth_private *pep) | 
|  | { | 
|  | int skb_size; | 
|  |  | 
|  | /* | 
|  | * Reserve 2+14 bytes for an ethernet header (the hardware | 
|  | * automatically prepends 2 bytes of dummy data to each | 
|  | * received packet), 16 bytes for up to four VLAN tags, and | 
|  | * 4 bytes for the trailing FCS -- 36 bytes total. | 
|  | */ | 
|  | skb_size = pep->dev->mtu + 36; | 
|  |  | 
|  | /* | 
|  | * Make sure that the skb size is a multiple of 8 bytes, as | 
|  | * the lower three bits of the receive descriptor's buffer | 
|  | * size field are ignored by the hardware. | 
|  | */ | 
|  | pep->skb_size = (skb_size + 7) & ~7; | 
|  |  | 
|  | /* | 
|  | * If NET_SKB_PAD is smaller than a cache line, | 
|  | * netdev_alloc_skb() will cause skb->data to be misaligned | 
|  | * to a cache line boundary.  If this is the case, include | 
|  | * some extra space to allow re-aligning the data area. | 
|  | */ | 
|  | pep->skb_size += SKB_DMA_REALIGN; | 
|  |  | 
|  | } | 
|  |  | 
|  | static int set_port_config_ext(struct pxa168_eth_private *pep) | 
|  | { | 
|  | int skb_size; | 
|  |  | 
|  | pxa168_eth_recalc_skb_size(pep); | 
|  | if  (pep->skb_size <= 1518) | 
|  | skb_size = PCXR_MFL_1518; | 
|  | else if (pep->skb_size <= 1536) | 
|  | skb_size = PCXR_MFL_1536; | 
|  | else if (pep->skb_size <= 2048) | 
|  | skb_size = PCXR_MFL_2048; | 
|  | else | 
|  | skb_size = PCXR_MFL_64K; | 
|  |  | 
|  | /* Extended Port Configuration */ | 
|  | wrl(pep, | 
|  | PORT_CONFIG_EXT, PCXR_2BSM | /* Two byte prefix aligns IP hdr */ | 
|  | PCXR_DSCP_EN |		 /* Enable DSCP in IP */ | 
|  | skb_size | PCXR_FLP |	 /* do not force link pass */ | 
|  | PCXR_TX_HIGH_PRI);		 /* Transmit - high priority queue */ | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int pxa168_init_hw(struct pxa168_eth_private *pep) | 
|  | { | 
|  | int err = 0; | 
|  |  | 
|  | /* Disable interrupts */ | 
|  | wrl(pep, INT_MASK, 0); | 
|  | wrl(pep, INT_CAUSE, 0); | 
|  | /* Write to ICR to clear interrupts. */ | 
|  | wrl(pep, INT_W_CLEAR, 0); | 
|  | /* Abort any transmit and receive operations and put DMA | 
|  | * in idle state. | 
|  | */ | 
|  | abort_dma(pep); | 
|  | /* Initialize address hash table */ | 
|  | err = init_hash_table(pep); | 
|  | if (err) | 
|  | return err; | 
|  | /* SDMA configuration */ | 
|  | wrl(pep, SDMA_CONFIG, SDCR_BSZ8 |	/* Burst size = 32 bytes */ | 
|  | SDCR_RIFB |				/* Rx interrupt on frame */ | 
|  | SDCR_BLMT |				/* Little endian transmit */ | 
|  | SDCR_BLMR |				/* Little endian receive */ | 
|  | SDCR_RC_MAX_RETRANS);		/* Max retransmit count */ | 
|  | /* Port Configuration */ | 
|  | wrl(pep, PORT_CONFIG, PCR_HS);		/* Hash size is 1/2kb */ | 
|  | set_port_config_ext(pep); | 
|  |  | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int rxq_init(struct net_device *dev) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  | struct rx_desc *p_rx_desc; | 
|  | int size = 0, i = 0; | 
|  | int rx_desc_num = pep->rx_ring_size; | 
|  |  | 
|  | /* Allocate RX skb rings */ | 
|  | pep->rx_skb = kmalloc(sizeof(*pep->rx_skb) * pep->rx_ring_size, | 
|  | GFP_KERNEL); | 
|  | if (!pep->rx_skb) { | 
|  | printk(KERN_ERR "%s: Cannot alloc RX skb ring\n", dev->name); | 
|  | return -ENOMEM; | 
|  | } | 
|  | /* Allocate RX ring */ | 
|  | pep->rx_desc_count = 0; | 
|  | size = pep->rx_ring_size * sizeof(struct rx_desc); | 
|  | pep->rx_desc_area_size = size; | 
|  | pep->p_rx_desc_area = dma_alloc_coherent(pep->dev->dev.parent, size, | 
|  | &pep->rx_desc_dma, GFP_KERNEL); | 
|  | if (!pep->p_rx_desc_area) { | 
|  | printk(KERN_ERR "%s: Cannot alloc RX ring (size %d bytes)\n", | 
|  | dev->name, size); | 
|  | goto out; | 
|  | } | 
|  | memset((void *)pep->p_rx_desc_area, 0, size); | 
|  | /* initialize the next_desc_ptr links in the Rx descriptors ring */ | 
|  | p_rx_desc = (struct rx_desc *)pep->p_rx_desc_area; | 
|  | for (i = 0; i < rx_desc_num; i++) { | 
|  | p_rx_desc[i].next_desc_ptr = pep->rx_desc_dma + | 
|  | ((i + 1) % rx_desc_num) * sizeof(struct rx_desc); | 
|  | } | 
|  | /* Save Rx desc pointer to driver struct. */ | 
|  | pep->rx_curr_desc_q = 0; | 
|  | pep->rx_used_desc_q = 0; | 
|  | pep->rx_desc_area_size = rx_desc_num * sizeof(struct rx_desc); | 
|  | return 0; | 
|  | out: | 
|  | kfree(pep->rx_skb); | 
|  | return -ENOMEM; | 
|  | } | 
|  |  | 
|  | static void rxq_deinit(struct net_device *dev) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  | int curr; | 
|  |  | 
|  | /* Free preallocated skb's on RX rings */ | 
|  | for (curr = 0; pep->rx_desc_count && curr < pep->rx_ring_size; curr++) { | 
|  | if (pep->rx_skb[curr]) { | 
|  | dev_kfree_skb(pep->rx_skb[curr]); | 
|  | pep->rx_desc_count--; | 
|  | } | 
|  | } | 
|  | if (pep->rx_desc_count) | 
|  | printk(KERN_ERR | 
|  | "Error in freeing Rx Ring. %d skb's still\n", | 
|  | pep->rx_desc_count); | 
|  | /* Free RX ring */ | 
|  | if (pep->p_rx_desc_area) | 
|  | dma_free_coherent(pep->dev->dev.parent, pep->rx_desc_area_size, | 
|  | pep->p_rx_desc_area, pep->rx_desc_dma); | 
|  | kfree(pep->rx_skb); | 
|  | } | 
|  |  | 
|  | static int txq_init(struct net_device *dev) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  | struct tx_desc *p_tx_desc; | 
|  | int size = 0, i = 0; | 
|  | int tx_desc_num = pep->tx_ring_size; | 
|  |  | 
|  | pep->tx_skb = kmalloc(sizeof(*pep->tx_skb) * pep->tx_ring_size, | 
|  | GFP_KERNEL); | 
|  | if (!pep->tx_skb) { | 
|  | printk(KERN_ERR "%s: Cannot alloc TX skb ring\n", dev->name); | 
|  | return -ENOMEM; | 
|  | } | 
|  | /* Allocate TX ring */ | 
|  | pep->tx_desc_count = 0; | 
|  | size = pep->tx_ring_size * sizeof(struct tx_desc); | 
|  | pep->tx_desc_area_size = size; | 
|  | pep->p_tx_desc_area = dma_alloc_coherent(pep->dev->dev.parent, size, | 
|  | &pep->tx_desc_dma, GFP_KERNEL); | 
|  | if (!pep->p_tx_desc_area) { | 
|  | printk(KERN_ERR "%s: Cannot allocate Tx Ring (size %d bytes)\n", | 
|  | dev->name, size); | 
|  | goto out; | 
|  | } | 
|  | memset((void *)pep->p_tx_desc_area, 0, pep->tx_desc_area_size); | 
|  | /* Initialize the next_desc_ptr links in the Tx descriptors ring */ | 
|  | p_tx_desc = (struct tx_desc *)pep->p_tx_desc_area; | 
|  | for (i = 0; i < tx_desc_num; i++) { | 
|  | p_tx_desc[i].next_desc_ptr = pep->tx_desc_dma + | 
|  | ((i + 1) % tx_desc_num) * sizeof(struct tx_desc); | 
|  | } | 
|  | pep->tx_curr_desc_q = 0; | 
|  | pep->tx_used_desc_q = 0; | 
|  | pep->tx_desc_area_size = tx_desc_num * sizeof(struct tx_desc); | 
|  | return 0; | 
|  | out: | 
|  | kfree(pep->tx_skb); | 
|  | return -ENOMEM; | 
|  | } | 
|  |  | 
|  | static void txq_deinit(struct net_device *dev) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  |  | 
|  | /* Free outstanding skb's on TX ring */ | 
|  | txq_reclaim(dev, 1); | 
|  | BUG_ON(pep->tx_used_desc_q != pep->tx_curr_desc_q); | 
|  | /* Free TX ring */ | 
|  | if (pep->p_tx_desc_area) | 
|  | dma_free_coherent(pep->dev->dev.parent, pep->tx_desc_area_size, | 
|  | pep->p_tx_desc_area, pep->tx_desc_dma); | 
|  | kfree(pep->tx_skb); | 
|  | } | 
|  |  | 
|  | static int pxa168_eth_open(struct net_device *dev) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  | int err; | 
|  |  | 
|  | err = request_irq(dev->irq, pxa168_eth_int_handler, | 
|  | IRQF_DISABLED, dev->name, dev); | 
|  | if (err) { | 
|  | dev_printk(KERN_ERR, &dev->dev, "can't assign irq\n"); | 
|  | return -EAGAIN; | 
|  | } | 
|  | pep->rx_resource_err = 0; | 
|  | err = rxq_init(dev); | 
|  | if (err != 0) | 
|  | goto out_free_irq; | 
|  | err = txq_init(dev); | 
|  | if (err != 0) | 
|  | goto out_free_rx_skb; | 
|  | pep->rx_used_desc_q = 0; | 
|  | pep->rx_curr_desc_q = 0; | 
|  |  | 
|  | /* Fill RX ring with skb's */ | 
|  | rxq_refill(dev); | 
|  | pep->rx_used_desc_q = 0; | 
|  | pep->rx_curr_desc_q = 0; | 
|  | netif_carrier_off(dev); | 
|  | eth_port_start(dev); | 
|  | napi_enable(&pep->napi); | 
|  | return 0; | 
|  | out_free_rx_skb: | 
|  | rxq_deinit(dev); | 
|  | out_free_irq: | 
|  | free_irq(dev->irq, dev); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int pxa168_eth_stop(struct net_device *dev) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  | eth_port_reset(dev); | 
|  |  | 
|  | /* Disable interrupts */ | 
|  | wrl(pep, INT_MASK, 0); | 
|  | wrl(pep, INT_CAUSE, 0); | 
|  | /* Write to ICR to clear interrupts. */ | 
|  | wrl(pep, INT_W_CLEAR, 0); | 
|  | napi_disable(&pep->napi); | 
|  | del_timer_sync(&pep->timeout); | 
|  | netif_carrier_off(dev); | 
|  | free_irq(dev->irq, dev); | 
|  | rxq_deinit(dev); | 
|  | txq_deinit(dev); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int pxa168_eth_change_mtu(struct net_device *dev, int mtu) | 
|  | { | 
|  | int retval; | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  |  | 
|  | if ((mtu > 9500) || (mtu < 68)) | 
|  | return -EINVAL; | 
|  |  | 
|  | dev->mtu = mtu; | 
|  | retval = set_port_config_ext(pep); | 
|  |  | 
|  | if (!netif_running(dev)) | 
|  | return 0; | 
|  |  | 
|  | /* | 
|  | * Stop and then re-open the interface. This will allocate RX | 
|  | * skbs of the new MTU. | 
|  | * There is a possible danger that the open will not succeed, | 
|  | * due to memory being full. | 
|  | */ | 
|  | pxa168_eth_stop(dev); | 
|  | if (pxa168_eth_open(dev)) { | 
|  | dev_printk(KERN_ERR, &dev->dev, | 
|  | "fatal error on re-opening device after " | 
|  | "MTU change\n"); | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int eth_alloc_tx_desc_index(struct pxa168_eth_private *pep) | 
|  | { | 
|  | int tx_desc_curr; | 
|  |  | 
|  | tx_desc_curr = pep->tx_curr_desc_q; | 
|  | pep->tx_curr_desc_q = (tx_desc_curr + 1) % pep->tx_ring_size; | 
|  | BUG_ON(pep->tx_curr_desc_q == pep->tx_used_desc_q); | 
|  | pep->tx_desc_count++; | 
|  |  | 
|  | return tx_desc_curr; | 
|  | } | 
|  |  | 
|  | static int pxa168_rx_poll(struct napi_struct *napi, int budget) | 
|  | { | 
|  | struct pxa168_eth_private *pep = | 
|  | container_of(napi, struct pxa168_eth_private, napi); | 
|  | struct net_device *dev = pep->dev; | 
|  | int work_done = 0; | 
|  |  | 
|  | if (unlikely(pep->work_todo & WORK_LINK)) { | 
|  | pep->work_todo &= ~(WORK_LINK); | 
|  | handle_link_event(pep); | 
|  | } | 
|  | /* | 
|  | * We call txq_reclaim every time since in NAPI interupts are disabled | 
|  | * and due to this we miss the TX_DONE interrupt,which is not updated in | 
|  | * interrupt status register. | 
|  | */ | 
|  | txq_reclaim(dev, 0); | 
|  | if (netif_queue_stopped(dev) | 
|  | && pep->tx_ring_size - pep->tx_desc_count > 1) { | 
|  | netif_wake_queue(dev); | 
|  | } | 
|  | work_done = rxq_process(dev, budget); | 
|  | if (work_done < budget) { | 
|  | napi_complete(napi); | 
|  | wrl(pep, INT_MASK, ALL_INTS); | 
|  | } | 
|  |  | 
|  | return work_done; | 
|  | } | 
|  |  | 
|  | static int pxa168_eth_start_xmit(struct sk_buff *skb, struct net_device *dev) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  | struct net_device_stats *stats = &dev->stats; | 
|  | struct tx_desc *desc; | 
|  | int tx_index; | 
|  | int length; | 
|  |  | 
|  | tx_index = eth_alloc_tx_desc_index(pep); | 
|  | desc = &pep->p_tx_desc_area[tx_index]; | 
|  | length = skb->len; | 
|  | pep->tx_skb[tx_index] = skb; | 
|  | desc->byte_cnt = length; | 
|  | desc->buf_ptr = dma_map_single(NULL, skb->data, length, DMA_TO_DEVICE); | 
|  | wmb(); | 
|  | desc->cmd_sts = BUF_OWNED_BY_DMA | TX_GEN_CRC | TX_FIRST_DESC | | 
|  | TX_ZERO_PADDING | TX_LAST_DESC | TX_EN_INT; | 
|  | wmb(); | 
|  | wrl(pep, SDMA_CMD, SDMA_CMD_TXDH | SDMA_CMD_ERD); | 
|  |  | 
|  | stats->tx_bytes += length; | 
|  | stats->tx_packets++; | 
|  | dev->trans_start = jiffies; | 
|  | if (pep->tx_ring_size - pep->tx_desc_count <= 1) { | 
|  | /* We handled the current skb, but now we are out of space.*/ | 
|  | netif_stop_queue(dev); | 
|  | } | 
|  |  | 
|  | return NETDEV_TX_OK; | 
|  | } | 
|  |  | 
|  | static int smi_wait_ready(struct pxa168_eth_private *pep) | 
|  | { | 
|  | int i = 0; | 
|  |  | 
|  | /* wait for the SMI register to become available */ | 
|  | for (i = 0; rdl(pep, SMI) & SMI_BUSY; i++) { | 
|  | if (i == PHY_WAIT_ITERATIONS) | 
|  | return -ETIMEDOUT; | 
|  | msleep(10); | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int pxa168_smi_read(struct mii_bus *bus, int phy_addr, int regnum) | 
|  | { | 
|  | struct pxa168_eth_private *pep = bus->priv; | 
|  | int i = 0; | 
|  | int val; | 
|  |  | 
|  | if (smi_wait_ready(pep)) { | 
|  | printk(KERN_WARNING "pxa168_eth: SMI bus busy timeout\n"); | 
|  | return -ETIMEDOUT; | 
|  | } | 
|  | wrl(pep, SMI, (phy_addr << 16) | (regnum << 21) | SMI_OP_R); | 
|  | /* now wait for the data to be valid */ | 
|  | for (i = 0; !((val = rdl(pep, SMI)) & SMI_R_VALID); i++) { | 
|  | if (i == PHY_WAIT_ITERATIONS) { | 
|  | printk(KERN_WARNING | 
|  | "pxa168_eth: SMI bus read not valid\n"); | 
|  | return -ENODEV; | 
|  | } | 
|  | msleep(10); | 
|  | } | 
|  |  | 
|  | return val & 0xffff; | 
|  | } | 
|  |  | 
|  | static int pxa168_smi_write(struct mii_bus *bus, int phy_addr, int regnum, | 
|  | u16 value) | 
|  | { | 
|  | struct pxa168_eth_private *pep = bus->priv; | 
|  |  | 
|  | if (smi_wait_ready(pep)) { | 
|  | printk(KERN_WARNING "pxa168_eth: SMI bus busy timeout\n"); | 
|  | return -ETIMEDOUT; | 
|  | } | 
|  |  | 
|  | wrl(pep, SMI, (phy_addr << 16) | (regnum << 21) | | 
|  | SMI_OP_W | (value & 0xffff)); | 
|  |  | 
|  | if (smi_wait_ready(pep)) { | 
|  | printk(KERN_ERR "pxa168_eth: SMI bus busy timeout\n"); | 
|  | return -ETIMEDOUT; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int pxa168_eth_do_ioctl(struct net_device *dev, struct ifreq *ifr, | 
|  | int cmd) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  | if (pep->phy != NULL) | 
|  | return phy_mii_ioctl(pep->phy, ifr, cmd); | 
|  |  | 
|  | return -EOPNOTSUPP; | 
|  | } | 
|  |  | 
|  | static struct phy_device *phy_scan(struct pxa168_eth_private *pep, int phy_addr) | 
|  | { | 
|  | struct mii_bus *bus = pep->smi_bus; | 
|  | struct phy_device *phydev; | 
|  | int start; | 
|  | int num; | 
|  | int i; | 
|  |  | 
|  | if (phy_addr == PXA168_ETH_PHY_ADDR_DEFAULT) { | 
|  | /* Scan entire range */ | 
|  | start = ethernet_phy_get(pep); | 
|  | num = 32; | 
|  | } else { | 
|  | /* Use phy addr specific to platform */ | 
|  | start = phy_addr & 0x1f; | 
|  | num = 1; | 
|  | } | 
|  | phydev = NULL; | 
|  | for (i = 0; i < num; i++) { | 
|  | int addr = (start + i) & 0x1f; | 
|  | if (bus->phy_map[addr] == NULL) | 
|  | mdiobus_scan(bus, addr); | 
|  |  | 
|  | if (phydev == NULL) { | 
|  | phydev = bus->phy_map[addr]; | 
|  | if (phydev != NULL) | 
|  | ethernet_phy_set_addr(pep, addr); | 
|  | } | 
|  | } | 
|  |  | 
|  | return phydev; | 
|  | } | 
|  |  | 
|  | static void phy_init(struct pxa168_eth_private *pep, int speed, int duplex) | 
|  | { | 
|  | struct phy_device *phy = pep->phy; | 
|  | ethernet_phy_reset(pep); | 
|  |  | 
|  | phy_attach(pep->dev, dev_name(&phy->dev), 0, PHY_INTERFACE_MODE_MII); | 
|  |  | 
|  | if (speed == 0) { | 
|  | phy->autoneg = AUTONEG_ENABLE; | 
|  | phy->speed = 0; | 
|  | phy->duplex = 0; | 
|  | phy->supported &= PHY_BASIC_FEATURES; | 
|  | phy->advertising = phy->supported | ADVERTISED_Autoneg; | 
|  | } else { | 
|  | phy->autoneg = AUTONEG_DISABLE; | 
|  | phy->advertising = 0; | 
|  | phy->speed = speed; | 
|  | phy->duplex = duplex; | 
|  | } | 
|  | phy_start_aneg(phy); | 
|  | } | 
|  |  | 
|  | static int ethernet_phy_setup(struct net_device *dev) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  |  | 
|  | if (pep->pd->init) | 
|  | pep->pd->init(); | 
|  | pep->phy = phy_scan(pep, pep->pd->phy_addr & 0x1f); | 
|  | if (pep->phy != NULL) | 
|  | phy_init(pep, pep->pd->speed, pep->pd->duplex); | 
|  | update_hash_table_mac_address(pep, NULL, dev->dev_addr); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int pxa168_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  | int err; | 
|  |  | 
|  | err = phy_read_status(pep->phy); | 
|  | if (err == 0) | 
|  | err = phy_ethtool_gset(pep->phy, cmd); | 
|  |  | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int pxa168_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) | 
|  | { | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  |  | 
|  | return phy_ethtool_sset(pep->phy, cmd); | 
|  | } | 
|  |  | 
|  | static void pxa168_get_drvinfo(struct net_device *dev, | 
|  | struct ethtool_drvinfo *info) | 
|  | { | 
|  | strncpy(info->driver, DRIVER_NAME, 32); | 
|  | strncpy(info->version, DRIVER_VERSION, 32); | 
|  | strncpy(info->fw_version, "N/A", 32); | 
|  | strncpy(info->bus_info, "N/A", 32); | 
|  | } | 
|  |  | 
|  | static const struct ethtool_ops pxa168_ethtool_ops = { | 
|  | .get_settings = pxa168_get_settings, | 
|  | .set_settings = pxa168_set_settings, | 
|  | .get_drvinfo = pxa168_get_drvinfo, | 
|  | .get_link = ethtool_op_get_link, | 
|  | }; | 
|  |  | 
|  | static const struct net_device_ops pxa168_eth_netdev_ops = { | 
|  | .ndo_open = pxa168_eth_open, | 
|  | .ndo_stop = pxa168_eth_stop, | 
|  | .ndo_start_xmit = pxa168_eth_start_xmit, | 
|  | .ndo_set_rx_mode = pxa168_eth_set_rx_mode, | 
|  | .ndo_set_mac_address = pxa168_eth_set_mac_address, | 
|  | .ndo_validate_addr = eth_validate_addr, | 
|  | .ndo_do_ioctl = pxa168_eth_do_ioctl, | 
|  | .ndo_change_mtu = pxa168_eth_change_mtu, | 
|  | .ndo_tx_timeout = pxa168_eth_tx_timeout, | 
|  | }; | 
|  |  | 
|  | static int pxa168_eth_probe(struct platform_device *pdev) | 
|  | { | 
|  | struct pxa168_eth_private *pep = NULL; | 
|  | struct net_device *dev = NULL; | 
|  | struct resource *res; | 
|  | struct clk *clk; | 
|  | int err; | 
|  |  | 
|  | printk(KERN_NOTICE "PXA168 10/100 Ethernet Driver\n"); | 
|  |  | 
|  | clk = clk_get(&pdev->dev, "MFUCLK"); | 
|  | if (IS_ERR(clk)) { | 
|  | printk(KERN_ERR "%s: Fast Ethernet failed to get clock\n", | 
|  | DRIVER_NAME); | 
|  | return -ENODEV; | 
|  | } | 
|  | clk_enable(clk); | 
|  |  | 
|  | dev = alloc_etherdev(sizeof(struct pxa168_eth_private)); | 
|  | if (!dev) { | 
|  | err = -ENOMEM; | 
|  | goto err_clk; | 
|  | } | 
|  |  | 
|  | platform_set_drvdata(pdev, dev); | 
|  | pep = netdev_priv(dev); | 
|  | pep->dev = dev; | 
|  | pep->clk = clk; | 
|  | res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | 
|  | if (res == NULL) { | 
|  | err = -ENODEV; | 
|  | goto err_netdev; | 
|  | } | 
|  | pep->base = ioremap(res->start, resource_size(res)); | 
|  | if (pep->base == NULL) { | 
|  | err = -ENOMEM; | 
|  | goto err_netdev; | 
|  | } | 
|  | res = platform_get_resource(pdev, IORESOURCE_IRQ, 0); | 
|  | BUG_ON(!res); | 
|  | dev->irq = res->start; | 
|  | dev->netdev_ops = &pxa168_eth_netdev_ops; | 
|  | dev->watchdog_timeo = 2 * HZ; | 
|  | dev->base_addr = 0; | 
|  | SET_ETHTOOL_OPS(dev, &pxa168_ethtool_ops); | 
|  |  | 
|  | INIT_WORK(&pep->tx_timeout_task, pxa168_eth_tx_timeout_task); | 
|  |  | 
|  | printk(KERN_INFO "%s:Using random mac address\n", DRIVER_NAME); | 
|  | random_ether_addr(dev->dev_addr); | 
|  |  | 
|  | pep->pd = pdev->dev.platform_data; | 
|  | pep->rx_ring_size = NUM_RX_DESCS; | 
|  | if (pep->pd->rx_queue_size) | 
|  | pep->rx_ring_size = pep->pd->rx_queue_size; | 
|  |  | 
|  | pep->tx_ring_size = NUM_TX_DESCS; | 
|  | if (pep->pd->tx_queue_size) | 
|  | pep->tx_ring_size = pep->pd->tx_queue_size; | 
|  |  | 
|  | pep->port_num = pep->pd->port_number; | 
|  | /* Hardware supports only 3 ports */ | 
|  | BUG_ON(pep->port_num > 2); | 
|  | netif_napi_add(dev, &pep->napi, pxa168_rx_poll, pep->rx_ring_size); | 
|  |  | 
|  | memset(&pep->timeout, 0, sizeof(struct timer_list)); | 
|  | init_timer(&pep->timeout); | 
|  | pep->timeout.function = rxq_refill_timer_wrapper; | 
|  | pep->timeout.data = (unsigned long)pep; | 
|  |  | 
|  | pep->smi_bus = mdiobus_alloc(); | 
|  | if (pep->smi_bus == NULL) { | 
|  | err = -ENOMEM; | 
|  | goto err_base; | 
|  | } | 
|  | pep->smi_bus->priv = pep; | 
|  | pep->smi_bus->name = "pxa168_eth smi"; | 
|  | pep->smi_bus->read = pxa168_smi_read; | 
|  | pep->smi_bus->write = pxa168_smi_write; | 
|  | snprintf(pep->smi_bus->id, MII_BUS_ID_SIZE, "%d", pdev->id); | 
|  | pep->smi_bus->parent = &pdev->dev; | 
|  | pep->smi_bus->phy_mask = 0xffffffff; | 
|  | err = mdiobus_register(pep->smi_bus); | 
|  | if (err) | 
|  | goto err_free_mdio; | 
|  |  | 
|  | pxa168_init_hw(pep); | 
|  | err = ethernet_phy_setup(dev); | 
|  | if (err) | 
|  | goto err_mdiobus; | 
|  | SET_NETDEV_DEV(dev, &pdev->dev); | 
|  | err = register_netdev(dev); | 
|  | if (err) | 
|  | goto err_mdiobus; | 
|  | return 0; | 
|  |  | 
|  | err_mdiobus: | 
|  | mdiobus_unregister(pep->smi_bus); | 
|  | err_free_mdio: | 
|  | mdiobus_free(pep->smi_bus); | 
|  | err_base: | 
|  | iounmap(pep->base); | 
|  | err_netdev: | 
|  | free_netdev(dev); | 
|  | err_clk: | 
|  | clk_disable(clk); | 
|  | clk_put(clk); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int pxa168_eth_remove(struct platform_device *pdev) | 
|  | { | 
|  | struct net_device *dev = platform_get_drvdata(pdev); | 
|  | struct pxa168_eth_private *pep = netdev_priv(dev); | 
|  |  | 
|  | if (pep->htpr) { | 
|  | dma_free_coherent(pep->dev->dev.parent, HASH_ADDR_TABLE_SIZE, | 
|  | pep->htpr, pep->htpr_dma); | 
|  | pep->htpr = NULL; | 
|  | } | 
|  | if (pep->clk) { | 
|  | clk_disable(pep->clk); | 
|  | clk_put(pep->clk); | 
|  | pep->clk = NULL; | 
|  | } | 
|  | if (pep->phy != NULL) | 
|  | phy_detach(pep->phy); | 
|  |  | 
|  | iounmap(pep->base); | 
|  | pep->base = NULL; | 
|  | mdiobus_unregister(pep->smi_bus); | 
|  | mdiobus_free(pep->smi_bus); | 
|  | unregister_netdev(dev); | 
|  | cancel_work_sync(&pep->tx_timeout_task); | 
|  | free_netdev(dev); | 
|  | platform_set_drvdata(pdev, NULL); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void pxa168_eth_shutdown(struct platform_device *pdev) | 
|  | { | 
|  | struct net_device *dev = platform_get_drvdata(pdev); | 
|  | eth_port_reset(dev); | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_PM | 
|  | static int pxa168_eth_resume(struct platform_device *pdev) | 
|  | { | 
|  | return -ENOSYS; | 
|  | } | 
|  |  | 
|  | static int pxa168_eth_suspend(struct platform_device *pdev, pm_message_t state) | 
|  | { | 
|  | return -ENOSYS; | 
|  | } | 
|  |  | 
|  | #else | 
|  | #define pxa168_eth_resume NULL | 
|  | #define pxa168_eth_suspend NULL | 
|  | #endif | 
|  |  | 
|  | static struct platform_driver pxa168_eth_driver = { | 
|  | .probe = pxa168_eth_probe, | 
|  | .remove = pxa168_eth_remove, | 
|  | .shutdown = pxa168_eth_shutdown, | 
|  | .resume = pxa168_eth_resume, | 
|  | .suspend = pxa168_eth_suspend, | 
|  | .driver = { | 
|  | .name = DRIVER_NAME, | 
|  | }, | 
|  | }; | 
|  |  | 
|  | static int __init pxa168_init_module(void) | 
|  | { | 
|  | return platform_driver_register(&pxa168_eth_driver); | 
|  | } | 
|  |  | 
|  | static void __exit pxa168_cleanup_module(void) | 
|  | { | 
|  | platform_driver_unregister(&pxa168_eth_driver); | 
|  | } | 
|  |  | 
|  | module_init(pxa168_init_module); | 
|  | module_exit(pxa168_cleanup_module); | 
|  |  | 
|  | MODULE_LICENSE("GPL"); | 
|  | MODULE_DESCRIPTION("Ethernet driver for Marvell PXA168"); | 
|  | MODULE_ALIAS("platform:pxa168_eth"); |