| #include <linux/bitops.h> | 
 | #include <linux/kernel.h> | 
 | #include <linux/module.h> | 
 | #include <linux/interrupt.h> | 
 | #include <linux/irq.h> | 
 | #include <linux/spinlock.h> | 
 | #include <linux/list.h> | 
 | #include <linux/device.h> | 
 | #include <linux/err.h> | 
 | #include <linux/debugfs.h> | 
 | #include <linux/seq_file.h> | 
 | #include <linux/gpio.h> | 
 | #include <linux/of_gpio.h> | 
 | #include <linux/idr.h> | 
 | #include <linux/slab.h> | 
 | #include <linux/acpi.h> | 
 | #include <linux/gpio/driver.h> | 
 | #include <linux/gpio/machine.h> | 
 | #include <linux/pinctrl/consumer.h> | 
 | #include <linux/cdev.h> | 
 | #include <linux/fs.h> | 
 | #include <linux/uaccess.h> | 
 | #include <linux/compat.h> | 
 | #include <linux/anon_inodes.h> | 
 | #include <linux/file.h> | 
 | #include <linux/kfifo.h> | 
 | #include <linux/poll.h> | 
 | #include <linux/timekeeping.h> | 
 | #include <uapi/linux/gpio.h> | 
 |  | 
 | #include "gpiolib.h" | 
 |  | 
 | #define CREATE_TRACE_POINTS | 
 | #include <trace/events/gpio.h> | 
 |  | 
 | /* Implementation infrastructure for GPIO interfaces. | 
 |  * | 
 |  * The GPIO programming interface allows for inlining speed-critical | 
 |  * get/set operations for common cases, so that access to SOC-integrated | 
 |  * GPIOs can sometimes cost only an instruction or two per bit. | 
 |  */ | 
 |  | 
 |  | 
 | /* When debugging, extend minimal trust to callers and platform code. | 
 |  * Also emit diagnostic messages that may help initial bringup, when | 
 |  * board setup or driver bugs are most common. | 
 |  * | 
 |  * Otherwise, minimize overhead in what may be bitbanging codepaths. | 
 |  */ | 
 | #ifdef	DEBUG | 
 | #define	extra_checks	1 | 
 | #else | 
 | #define	extra_checks	0 | 
 | #endif | 
 |  | 
 | /* Device and char device-related information */ | 
 | static DEFINE_IDA(gpio_ida); | 
 | static dev_t gpio_devt; | 
 | #define GPIO_DEV_MAX 256 /* 256 GPIO chip devices supported */ | 
 | static struct bus_type gpio_bus_type = { | 
 | 	.name = "gpio", | 
 | }; | 
 |  | 
 | /* gpio_lock prevents conflicts during gpio_desc[] table updates. | 
 |  * While any GPIO is requested, its gpio_chip is not removable; | 
 |  * each GPIO's "requested" flag serves as a lock and refcount. | 
 |  */ | 
 | DEFINE_SPINLOCK(gpio_lock); | 
 |  | 
 | static DEFINE_MUTEX(gpio_lookup_lock); | 
 | static LIST_HEAD(gpio_lookup_list); | 
 | LIST_HEAD(gpio_devices); | 
 |  | 
 | static void gpiochip_free_hogs(struct gpio_chip *chip); | 
 | static void gpiochip_irqchip_remove(struct gpio_chip *gpiochip); | 
 | static int gpiochip_irqchip_init_valid_mask(struct gpio_chip *gpiochip); | 
 | static void gpiochip_irqchip_free_valid_mask(struct gpio_chip *gpiochip); | 
 |  | 
 | static bool gpiolib_initialized; | 
 |  | 
 | static inline void desc_set_label(struct gpio_desc *d, const char *label) | 
 | { | 
 | 	d->label = label; | 
 | } | 
 |  | 
 | /** | 
 |  * Convert a GPIO number to its descriptor | 
 |  */ | 
 | struct gpio_desc *gpio_to_desc(unsigned gpio) | 
 | { | 
 | 	struct gpio_device *gdev; | 
 | 	unsigned long flags; | 
 |  | 
 | 	spin_lock_irqsave(&gpio_lock, flags); | 
 |  | 
 | 	list_for_each_entry(gdev, &gpio_devices, list) { | 
 | 		if (gdev->base <= gpio && | 
 | 		    gdev->base + gdev->ngpio > gpio) { | 
 | 			spin_unlock_irqrestore(&gpio_lock, flags); | 
 | 			return &gdev->descs[gpio - gdev->base]; | 
 | 		} | 
 | 	} | 
 |  | 
 | 	spin_unlock_irqrestore(&gpio_lock, flags); | 
 |  | 
 | 	if (!gpio_is_valid(gpio)) | 
 | 		WARN(1, "invalid GPIO %d\n", gpio); | 
 |  | 
 | 	return NULL; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpio_to_desc); | 
 |  | 
 | /** | 
 |  * Get the GPIO descriptor corresponding to the given hw number for this chip. | 
 |  */ | 
 | struct gpio_desc *gpiochip_get_desc(struct gpio_chip *chip, | 
 | 				    u16 hwnum) | 
 | { | 
 | 	struct gpio_device *gdev = chip->gpiodev; | 
 |  | 
 | 	if (hwnum >= gdev->ngpio) | 
 | 		return ERR_PTR(-EINVAL); | 
 |  | 
 | 	return &gdev->descs[hwnum]; | 
 | } | 
 |  | 
 | /** | 
 |  * Convert a GPIO descriptor to the integer namespace. | 
 |  * This should disappear in the future but is needed since we still | 
 |  * use GPIO numbers for error messages and sysfs nodes | 
 |  */ | 
 | int desc_to_gpio(const struct gpio_desc *desc) | 
 | { | 
 | 	return desc->gdev->base + (desc - &desc->gdev->descs[0]); | 
 | } | 
 | EXPORT_SYMBOL_GPL(desc_to_gpio); | 
 |  | 
 |  | 
 | /** | 
 |  * gpiod_to_chip - Return the GPIO chip to which a GPIO descriptor belongs | 
 |  * @desc:	descriptor to return the chip of | 
 |  */ | 
 | struct gpio_chip *gpiod_to_chip(const struct gpio_desc *desc) | 
 | { | 
 | 	if (!desc || !desc->gdev || !desc->gdev->chip) | 
 | 		return NULL; | 
 | 	return desc->gdev->chip; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_to_chip); | 
 |  | 
 | /* dynamic allocation of GPIOs, e.g. on a hotplugged device */ | 
 | static int gpiochip_find_base(int ngpio) | 
 | { | 
 | 	struct gpio_device *gdev; | 
 | 	int base = ARCH_NR_GPIOS - ngpio; | 
 |  | 
 | 	list_for_each_entry_reverse(gdev, &gpio_devices, list) { | 
 | 		/* found a free space? */ | 
 | 		if (gdev->base + gdev->ngpio <= base) | 
 | 			break; | 
 | 		else | 
 | 			/* nope, check the space right before the chip */ | 
 | 			base = gdev->base - ngpio; | 
 | 	} | 
 |  | 
 | 	if (gpio_is_valid(base)) { | 
 | 		pr_debug("%s: found new base at %d\n", __func__, base); | 
 | 		return base; | 
 | 	} else { | 
 | 		pr_err("%s: cannot find free range\n", __func__); | 
 | 		return -ENOSPC; | 
 | 	} | 
 | } | 
 |  | 
 | /** | 
 |  * gpiod_get_direction - return the current direction of a GPIO | 
 |  * @desc:	GPIO to get the direction of | 
 |  * | 
 |  * Return GPIOF_DIR_IN or GPIOF_DIR_OUT, or an error code in case of error. | 
 |  * | 
 |  * This function may sleep if gpiod_cansleep() is true. | 
 |  */ | 
 | int gpiod_get_direction(struct gpio_desc *desc) | 
 | { | 
 | 	struct gpio_chip	*chip; | 
 | 	unsigned		offset; | 
 | 	int			status = -EINVAL; | 
 |  | 
 | 	chip = gpiod_to_chip(desc); | 
 | 	offset = gpio_chip_hwgpio(desc); | 
 |  | 
 | 	if (!chip->get_direction) | 
 | 		return status; | 
 |  | 
 | 	status = chip->get_direction(chip, offset); | 
 | 	if (status > 0) { | 
 | 		/* GPIOF_DIR_IN, or other positive */ | 
 | 		status = 1; | 
 | 		clear_bit(FLAG_IS_OUT, &desc->flags); | 
 | 	} | 
 | 	if (status == 0) { | 
 | 		/* GPIOF_DIR_OUT */ | 
 | 		set_bit(FLAG_IS_OUT, &desc->flags); | 
 | 	} | 
 | 	return status; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_get_direction); | 
 |  | 
 | /* | 
 |  * Add a new chip to the global chips list, keeping the list of chips sorted | 
 |  * by range(means [base, base + ngpio - 1]) order. | 
 |  * | 
 |  * Return -EBUSY if the new chip overlaps with some other chip's integer | 
 |  * space. | 
 |  */ | 
 | static int gpiodev_add_to_list(struct gpio_device *gdev) | 
 | { | 
 | 	struct gpio_device *prev, *next; | 
 |  | 
 | 	if (list_empty(&gpio_devices)) { | 
 | 		/* initial entry in list */ | 
 | 		list_add_tail(&gdev->list, &gpio_devices); | 
 | 		return 0; | 
 | 	} | 
 |  | 
 | 	next = list_entry(gpio_devices.next, struct gpio_device, list); | 
 | 	if (gdev->base + gdev->ngpio <= next->base) { | 
 | 		/* add before first entry */ | 
 | 		list_add(&gdev->list, &gpio_devices); | 
 | 		return 0; | 
 | 	} | 
 |  | 
 | 	prev = list_entry(gpio_devices.prev, struct gpio_device, list); | 
 | 	if (prev->base + prev->ngpio <= gdev->base) { | 
 | 		/* add behind last entry */ | 
 | 		list_add_tail(&gdev->list, &gpio_devices); | 
 | 		return 0; | 
 | 	} | 
 |  | 
 | 	list_for_each_entry_safe(prev, next, &gpio_devices, list) { | 
 | 		/* at the end of the list */ | 
 | 		if (&next->list == &gpio_devices) | 
 | 			break; | 
 |  | 
 | 		/* add between prev and next */ | 
 | 		if (prev->base + prev->ngpio <= gdev->base | 
 | 				&& gdev->base + gdev->ngpio <= next->base) { | 
 | 			list_add(&gdev->list, &prev->list); | 
 | 			return 0; | 
 | 		} | 
 | 	} | 
 |  | 
 | 	dev_err(&gdev->dev, "GPIO integer space overlap, cannot add chip\n"); | 
 | 	return -EBUSY; | 
 | } | 
 |  | 
 | /** | 
 |  * Convert a GPIO name to its descriptor | 
 |  */ | 
 | static struct gpio_desc *gpio_name_to_desc(const char * const name) | 
 | { | 
 | 	struct gpio_device *gdev; | 
 | 	unsigned long flags; | 
 |  | 
 | 	spin_lock_irqsave(&gpio_lock, flags); | 
 |  | 
 | 	list_for_each_entry(gdev, &gpio_devices, list) { | 
 | 		int i; | 
 |  | 
 | 		for (i = 0; i != gdev->ngpio; ++i) { | 
 | 			struct gpio_desc *desc = &gdev->descs[i]; | 
 |  | 
 | 			if (!desc->name || !name) | 
 | 				continue; | 
 |  | 
 | 			if (!strcmp(desc->name, name)) { | 
 | 				spin_unlock_irqrestore(&gpio_lock, flags); | 
 | 				return desc; | 
 | 			} | 
 | 		} | 
 | 	} | 
 |  | 
 | 	spin_unlock_irqrestore(&gpio_lock, flags); | 
 |  | 
 | 	return NULL; | 
 | } | 
 |  | 
 | /* | 
 |  * Takes the names from gc->names and checks if they are all unique. If they | 
 |  * are, they are assigned to their gpio descriptors. | 
 |  * | 
 |  * Warning if one of the names is already used for a different GPIO. | 
 |  */ | 
 | static int gpiochip_set_desc_names(struct gpio_chip *gc) | 
 | { | 
 | 	struct gpio_device *gdev = gc->gpiodev; | 
 | 	int i; | 
 |  | 
 | 	if (!gc->names) | 
 | 		return 0; | 
 |  | 
 | 	/* First check all names if they are unique */ | 
 | 	for (i = 0; i != gc->ngpio; ++i) { | 
 | 		struct gpio_desc *gpio; | 
 |  | 
 | 		gpio = gpio_name_to_desc(gc->names[i]); | 
 | 		if (gpio) | 
 | 			dev_warn(&gdev->dev, | 
 | 				 "Detected name collision for GPIO name '%s'\n", | 
 | 				 gc->names[i]); | 
 | 	} | 
 |  | 
 | 	/* Then add all names to the GPIO descriptors */ | 
 | 	for (i = 0; i != gc->ngpio; ++i) | 
 | 		gdev->descs[i].name = gc->names[i]; | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | /* | 
 |  * GPIO line handle management | 
 |  */ | 
 |  | 
 | /** | 
 |  * struct linehandle_state - contains the state of a userspace handle | 
 |  * @gdev: the GPIO device the handle pertains to | 
 |  * @label: consumer label used to tag descriptors | 
 |  * @descs: the GPIO descriptors held by this handle | 
 |  * @numdescs: the number of descriptors held in the descs array | 
 |  */ | 
 | struct linehandle_state { | 
 | 	struct gpio_device *gdev; | 
 | 	const char *label; | 
 | 	struct gpio_desc *descs[GPIOHANDLES_MAX]; | 
 | 	u32 numdescs; | 
 | }; | 
 |  | 
 | #define GPIOHANDLE_REQUEST_VALID_FLAGS \ | 
 | 	(GPIOHANDLE_REQUEST_INPUT | \ | 
 | 	GPIOHANDLE_REQUEST_OUTPUT | \ | 
 | 	GPIOHANDLE_REQUEST_ACTIVE_LOW | \ | 
 | 	GPIOHANDLE_REQUEST_OPEN_DRAIN | \ | 
 | 	GPIOHANDLE_REQUEST_OPEN_SOURCE) | 
 |  | 
 | static long linehandle_ioctl(struct file *filep, unsigned int cmd, | 
 | 			     unsigned long arg) | 
 | { | 
 | 	struct linehandle_state *lh = filep->private_data; | 
 | 	void __user *ip = (void __user *)arg; | 
 | 	struct gpiohandle_data ghd; | 
 | 	int i; | 
 |  | 
 | 	if (cmd == GPIOHANDLE_GET_LINE_VALUES_IOCTL) { | 
 | 		int val; | 
 |  | 
 | 		memset(&ghd, 0, sizeof(ghd)); | 
 |  | 
 | 		/* TODO: check if descriptors are really input */ | 
 | 		for (i = 0; i < lh->numdescs; i++) { | 
 | 			val = gpiod_get_value_cansleep(lh->descs[i]); | 
 | 			if (val < 0) | 
 | 				return val; | 
 | 			ghd.values[i] = val; | 
 | 		} | 
 |  | 
 | 		if (copy_to_user(ip, &ghd, sizeof(ghd))) | 
 | 			return -EFAULT; | 
 |  | 
 | 		return 0; | 
 | 	} else if (cmd == GPIOHANDLE_SET_LINE_VALUES_IOCTL) { | 
 | 		int vals[GPIOHANDLES_MAX]; | 
 |  | 
 | 		/* TODO: check if descriptors are really output */ | 
 | 		if (copy_from_user(&ghd, ip, sizeof(ghd))) | 
 | 			return -EFAULT; | 
 |  | 
 | 		/* Clamp all values to [0,1] */ | 
 | 		for (i = 0; i < lh->numdescs; i++) | 
 | 			vals[i] = !!ghd.values[i]; | 
 |  | 
 | 		/* Reuse the array setting function */ | 
 | 		gpiod_set_array_value_complex(false, | 
 | 					      true, | 
 | 					      lh->numdescs, | 
 | 					      lh->descs, | 
 | 					      vals); | 
 | 		return 0; | 
 | 	} | 
 | 	return -EINVAL; | 
 | } | 
 |  | 
 | #ifdef CONFIG_COMPAT | 
 | static long linehandle_ioctl_compat(struct file *filep, unsigned int cmd, | 
 | 			     unsigned long arg) | 
 | { | 
 | 	return linehandle_ioctl(filep, cmd, (unsigned long)compat_ptr(arg)); | 
 | } | 
 | #endif | 
 |  | 
 | static int linehandle_release(struct inode *inode, struct file *filep) | 
 | { | 
 | 	struct linehandle_state *lh = filep->private_data; | 
 | 	struct gpio_device *gdev = lh->gdev; | 
 | 	int i; | 
 |  | 
 | 	for (i = 0; i < lh->numdescs; i++) | 
 | 		gpiod_free(lh->descs[i]); | 
 | 	kfree(lh->label); | 
 | 	kfree(lh); | 
 | 	put_device(&gdev->dev); | 
 | 	return 0; | 
 | } | 
 |  | 
 | static const struct file_operations linehandle_fileops = { | 
 | 	.release = linehandle_release, | 
 | 	.owner = THIS_MODULE, | 
 | 	.llseek = noop_llseek, | 
 | 	.unlocked_ioctl = linehandle_ioctl, | 
 | #ifdef CONFIG_COMPAT | 
 | 	.compat_ioctl = linehandle_ioctl_compat, | 
 | #endif | 
 | }; | 
 |  | 
 | static int linehandle_create(struct gpio_device *gdev, void __user *ip) | 
 | { | 
 | 	struct gpiohandle_request handlereq; | 
 | 	struct linehandle_state *lh; | 
 | 	struct file *file; | 
 | 	int fd, i, ret; | 
 |  | 
 | 	if (copy_from_user(&handlereq, ip, sizeof(handlereq))) | 
 | 		return -EFAULT; | 
 | 	if ((handlereq.lines == 0) || (handlereq.lines > GPIOHANDLES_MAX)) | 
 | 		return -EINVAL; | 
 |  | 
 | 	lh = kzalloc(sizeof(*lh), GFP_KERNEL); | 
 | 	if (!lh) | 
 | 		return -ENOMEM; | 
 | 	lh->gdev = gdev; | 
 | 	get_device(&gdev->dev); | 
 |  | 
 | 	/* Make sure this is terminated */ | 
 | 	handlereq.consumer_label[sizeof(handlereq.consumer_label)-1] = '\0'; | 
 | 	if (strlen(handlereq.consumer_label)) { | 
 | 		lh->label = kstrdup(handlereq.consumer_label, | 
 | 				    GFP_KERNEL); | 
 | 		if (!lh->label) { | 
 | 			ret = -ENOMEM; | 
 | 			goto out_free_lh; | 
 | 		} | 
 | 	} | 
 |  | 
 | 	/* Request each GPIO */ | 
 | 	for (i = 0; i < handlereq.lines; i++) { | 
 | 		u32 offset = handlereq.lineoffsets[i]; | 
 | 		u32 lflags = handlereq.flags; | 
 | 		struct gpio_desc *desc; | 
 |  | 
 | 		if (offset >= gdev->ngpio) { | 
 | 			ret = -EINVAL; | 
 | 			goto out_free_descs; | 
 | 		} | 
 |  | 
 | 		/* Return an error if a unknown flag is set */ | 
 | 		if (lflags & ~GPIOHANDLE_REQUEST_VALID_FLAGS) { | 
 | 			ret = -EINVAL; | 
 | 			goto out_free_descs; | 
 | 		} | 
 |  | 
 | 		desc = &gdev->descs[offset]; | 
 | 		ret = gpiod_request(desc, lh->label); | 
 | 		if (ret) | 
 | 			goto out_free_descs; | 
 | 		lh->descs[i] = desc; | 
 |  | 
 | 		if (lflags & GPIOHANDLE_REQUEST_ACTIVE_LOW) | 
 | 			set_bit(FLAG_ACTIVE_LOW, &desc->flags); | 
 | 		if (lflags & GPIOHANDLE_REQUEST_OPEN_DRAIN) | 
 | 			set_bit(FLAG_OPEN_DRAIN, &desc->flags); | 
 | 		if (lflags & GPIOHANDLE_REQUEST_OPEN_SOURCE) | 
 | 			set_bit(FLAG_OPEN_SOURCE, &desc->flags); | 
 |  | 
 | 		/* | 
 | 		 * Lines have to be requested explicitly for input | 
 | 		 * or output, else the line will be treated "as is". | 
 | 		 */ | 
 | 		if (lflags & GPIOHANDLE_REQUEST_OUTPUT) { | 
 | 			int val = !!handlereq.default_values[i]; | 
 |  | 
 | 			ret = gpiod_direction_output(desc, val); | 
 | 			if (ret) | 
 | 				goto out_free_descs; | 
 | 		} else if (lflags & GPIOHANDLE_REQUEST_INPUT) { | 
 | 			ret = gpiod_direction_input(desc); | 
 | 			if (ret) | 
 | 				goto out_free_descs; | 
 | 		} | 
 | 		dev_dbg(&gdev->dev, "registered chardev handle for line %d\n", | 
 | 			offset); | 
 | 	} | 
 | 	/* Let i point at the last handle */ | 
 | 	i--; | 
 | 	lh->numdescs = handlereq.lines; | 
 |  | 
 | 	fd = get_unused_fd_flags(O_RDONLY | O_CLOEXEC); | 
 | 	if (fd < 0) { | 
 | 		ret = fd; | 
 | 		goto out_free_descs; | 
 | 	} | 
 |  | 
 | 	file = anon_inode_getfile("gpio-linehandle", | 
 | 				  &linehandle_fileops, | 
 | 				  lh, | 
 | 				  O_RDONLY | O_CLOEXEC); | 
 | 	if (IS_ERR(file)) { | 
 | 		ret = PTR_ERR(file); | 
 | 		goto out_put_unused_fd; | 
 | 	} | 
 |  | 
 | 	handlereq.fd = fd; | 
 | 	if (copy_to_user(ip, &handlereq, sizeof(handlereq))) { | 
 | 		/* | 
 | 		 * fput() will trigger the release() callback, so do not go onto | 
 | 		 * the regular error cleanup path here. | 
 | 		 */ | 
 | 		fput(file); | 
 | 		put_unused_fd(fd); | 
 | 		return -EFAULT; | 
 | 	} | 
 |  | 
 | 	fd_install(fd, file); | 
 |  | 
 | 	dev_dbg(&gdev->dev, "registered chardev handle for %d lines\n", | 
 | 		lh->numdescs); | 
 |  | 
 | 	return 0; | 
 |  | 
 | out_put_unused_fd: | 
 | 	put_unused_fd(fd); | 
 | out_free_descs: | 
 | 	for (; i >= 0; i--) | 
 | 		gpiod_free(lh->descs[i]); | 
 | 	kfree(lh->label); | 
 | out_free_lh: | 
 | 	kfree(lh); | 
 | 	put_device(&gdev->dev); | 
 | 	return ret; | 
 | } | 
 |  | 
 | /* | 
 |  * GPIO line event management | 
 |  */ | 
 |  | 
 | /** | 
 |  * struct lineevent_state - contains the state of a userspace event | 
 |  * @gdev: the GPIO device the event pertains to | 
 |  * @label: consumer label used to tag descriptors | 
 |  * @desc: the GPIO descriptor held by this event | 
 |  * @eflags: the event flags this line was requested with | 
 |  * @irq: the interrupt that trigger in response to events on this GPIO | 
 |  * @wait: wait queue that handles blocking reads of events | 
 |  * @events: KFIFO for the GPIO events | 
 |  * @read_lock: mutex lock to protect reads from colliding with adding | 
 |  * new events to the FIFO | 
 |  */ | 
 | struct lineevent_state { | 
 | 	struct gpio_device *gdev; | 
 | 	const char *label; | 
 | 	struct gpio_desc *desc; | 
 | 	u32 eflags; | 
 | 	int irq; | 
 | 	wait_queue_head_t wait; | 
 | 	DECLARE_KFIFO(events, struct gpioevent_data, 16); | 
 | 	struct mutex read_lock; | 
 | }; | 
 |  | 
 | #define GPIOEVENT_REQUEST_VALID_FLAGS \ | 
 | 	(GPIOEVENT_REQUEST_RISING_EDGE | \ | 
 | 	GPIOEVENT_REQUEST_FALLING_EDGE) | 
 |  | 
 | static unsigned int lineevent_poll(struct file *filep, | 
 | 				   struct poll_table_struct *wait) | 
 | { | 
 | 	struct lineevent_state *le = filep->private_data; | 
 | 	unsigned int events = 0; | 
 |  | 
 | 	poll_wait(filep, &le->wait, wait); | 
 |  | 
 | 	if (!kfifo_is_empty(&le->events)) | 
 | 		events = POLLIN | POLLRDNORM; | 
 |  | 
 | 	return events; | 
 | } | 
 |  | 
 |  | 
 | static ssize_t lineevent_read(struct file *filep, | 
 | 			      char __user *buf, | 
 | 			      size_t count, | 
 | 			      loff_t *f_ps) | 
 | { | 
 | 	struct lineevent_state *le = filep->private_data; | 
 | 	unsigned int copied; | 
 | 	int ret; | 
 |  | 
 | 	if (count < sizeof(struct gpioevent_data)) | 
 | 		return -EINVAL; | 
 |  | 
 | 	do { | 
 | 		if (kfifo_is_empty(&le->events)) { | 
 | 			if (filep->f_flags & O_NONBLOCK) | 
 | 				return -EAGAIN; | 
 |  | 
 | 			ret = wait_event_interruptible(le->wait, | 
 | 					!kfifo_is_empty(&le->events)); | 
 | 			if (ret) | 
 | 				return ret; | 
 | 		} | 
 |  | 
 | 		if (mutex_lock_interruptible(&le->read_lock)) | 
 | 			return -ERESTARTSYS; | 
 | 		ret = kfifo_to_user(&le->events, buf, count, &copied); | 
 | 		mutex_unlock(&le->read_lock); | 
 |  | 
 | 		if (ret) | 
 | 			return ret; | 
 |  | 
 | 		/* | 
 | 		 * If we couldn't read anything from the fifo (a different | 
 | 		 * thread might have been faster) we either return -EAGAIN if | 
 | 		 * the file descriptor is non-blocking, otherwise we go back to | 
 | 		 * sleep and wait for more data to arrive. | 
 | 		 */ | 
 | 		if (copied == 0 && (filep->f_flags & O_NONBLOCK)) | 
 | 			return -EAGAIN; | 
 |  | 
 | 	} while (copied == 0); | 
 |  | 
 | 	return copied; | 
 | } | 
 |  | 
 | static int lineevent_release(struct inode *inode, struct file *filep) | 
 | { | 
 | 	struct lineevent_state *le = filep->private_data; | 
 | 	struct gpio_device *gdev = le->gdev; | 
 |  | 
 | 	free_irq(le->irq, le); | 
 | 	gpiod_free(le->desc); | 
 | 	kfree(le->label); | 
 | 	kfree(le); | 
 | 	put_device(&gdev->dev); | 
 | 	return 0; | 
 | } | 
 |  | 
 | static long lineevent_ioctl(struct file *filep, unsigned int cmd, | 
 | 			    unsigned long arg) | 
 | { | 
 | 	struct lineevent_state *le = filep->private_data; | 
 | 	void __user *ip = (void __user *)arg; | 
 | 	struct gpiohandle_data ghd; | 
 |  | 
 | 	/* | 
 | 	 * We can get the value for an event line but not set it, | 
 | 	 * because it is input by definition. | 
 | 	 */ | 
 | 	if (cmd == GPIOHANDLE_GET_LINE_VALUES_IOCTL) { | 
 | 		int val; | 
 |  | 
 | 		memset(&ghd, 0, sizeof(ghd)); | 
 |  | 
 | 		val = gpiod_get_value_cansleep(le->desc); | 
 | 		if (val < 0) | 
 | 			return val; | 
 | 		ghd.values[0] = val; | 
 |  | 
 | 		if (copy_to_user(ip, &ghd, sizeof(ghd))) | 
 | 			return -EFAULT; | 
 |  | 
 | 		return 0; | 
 | 	} | 
 | 	return -EINVAL; | 
 | } | 
 |  | 
 | #ifdef CONFIG_COMPAT | 
 | static long lineevent_ioctl_compat(struct file *filep, unsigned int cmd, | 
 | 				   unsigned long arg) | 
 | { | 
 | 	return lineevent_ioctl(filep, cmd, (unsigned long)compat_ptr(arg)); | 
 | } | 
 | #endif | 
 |  | 
 | static const struct file_operations lineevent_fileops = { | 
 | 	.release = lineevent_release, | 
 | 	.read = lineevent_read, | 
 | 	.poll = lineevent_poll, | 
 | 	.owner = THIS_MODULE, | 
 | 	.llseek = noop_llseek, | 
 | 	.unlocked_ioctl = lineevent_ioctl, | 
 | #ifdef CONFIG_COMPAT | 
 | 	.compat_ioctl = lineevent_ioctl_compat, | 
 | #endif | 
 | }; | 
 |  | 
 | static irqreturn_t lineevent_irq_thread(int irq, void *p) | 
 | { | 
 | 	struct lineevent_state *le = p; | 
 | 	struct gpioevent_data ge; | 
 | 	int ret; | 
 |  | 
 | 	ge.timestamp = ktime_get_real_ns(); | 
 |  | 
 | 	if (le->eflags & GPIOEVENT_REQUEST_BOTH_EDGES) { | 
 | 		int level = gpiod_get_value_cansleep(le->desc); | 
 |  | 
 | 		if (level) | 
 | 			/* Emit low-to-high event */ | 
 | 			ge.id = GPIOEVENT_EVENT_RISING_EDGE; | 
 | 		else | 
 | 			/* Emit high-to-low event */ | 
 | 			ge.id = GPIOEVENT_EVENT_FALLING_EDGE; | 
 | 	} else if (le->eflags & GPIOEVENT_REQUEST_RISING_EDGE) { | 
 | 		/* Emit low-to-high event */ | 
 | 		ge.id = GPIOEVENT_EVENT_RISING_EDGE; | 
 | 	} else if (le->eflags & GPIOEVENT_REQUEST_FALLING_EDGE) { | 
 | 		/* Emit high-to-low event */ | 
 | 		ge.id = GPIOEVENT_EVENT_FALLING_EDGE; | 
 | 	} else { | 
 | 		return IRQ_NONE; | 
 | 	} | 
 |  | 
 | 	ret = kfifo_put(&le->events, ge); | 
 | 	if (ret != 0) | 
 | 		wake_up_poll(&le->wait, POLLIN); | 
 |  | 
 | 	return IRQ_HANDLED; | 
 | } | 
 |  | 
 | static int lineevent_create(struct gpio_device *gdev, void __user *ip) | 
 | { | 
 | 	struct gpioevent_request eventreq; | 
 | 	struct lineevent_state *le; | 
 | 	struct gpio_desc *desc; | 
 | 	struct file *file; | 
 | 	u32 offset; | 
 | 	u32 lflags; | 
 | 	u32 eflags; | 
 | 	int fd; | 
 | 	int ret; | 
 | 	int irqflags = 0; | 
 |  | 
 | 	if (copy_from_user(&eventreq, ip, sizeof(eventreq))) | 
 | 		return -EFAULT; | 
 |  | 
 | 	le = kzalloc(sizeof(*le), GFP_KERNEL); | 
 | 	if (!le) | 
 | 		return -ENOMEM; | 
 | 	le->gdev = gdev; | 
 | 	get_device(&gdev->dev); | 
 |  | 
 | 	/* Make sure this is terminated */ | 
 | 	eventreq.consumer_label[sizeof(eventreq.consumer_label)-1] = '\0'; | 
 | 	if (strlen(eventreq.consumer_label)) { | 
 | 		le->label = kstrdup(eventreq.consumer_label, | 
 | 				    GFP_KERNEL); | 
 | 		if (!le->label) { | 
 | 			ret = -ENOMEM; | 
 | 			goto out_free_le; | 
 | 		} | 
 | 	} | 
 |  | 
 | 	offset = eventreq.lineoffset; | 
 | 	lflags = eventreq.handleflags; | 
 | 	eflags = eventreq.eventflags; | 
 |  | 
 | 	if (offset >= gdev->ngpio) { | 
 | 		ret = -EINVAL; | 
 | 		goto out_free_label; | 
 | 	} | 
 |  | 
 | 	/* Return an error if a unknown flag is set */ | 
 | 	if ((lflags & ~GPIOHANDLE_REQUEST_VALID_FLAGS) || | 
 | 	    (eflags & ~GPIOEVENT_REQUEST_VALID_FLAGS)) { | 
 | 		ret = -EINVAL; | 
 | 		goto out_free_label; | 
 | 	} | 
 |  | 
 | 	/* This is just wrong: we don't look for events on output lines */ | 
 | 	if (lflags & GPIOHANDLE_REQUEST_OUTPUT) { | 
 | 		ret = -EINVAL; | 
 | 		goto out_free_label; | 
 | 	} | 
 |  | 
 | 	desc = &gdev->descs[offset]; | 
 | 	ret = gpiod_request(desc, le->label); | 
 | 	if (ret) | 
 | 		goto out_free_desc; | 
 | 	le->desc = desc; | 
 | 	le->eflags = eflags; | 
 |  | 
 | 	if (lflags & GPIOHANDLE_REQUEST_ACTIVE_LOW) | 
 | 		set_bit(FLAG_ACTIVE_LOW, &desc->flags); | 
 | 	if (lflags & GPIOHANDLE_REQUEST_OPEN_DRAIN) | 
 | 		set_bit(FLAG_OPEN_DRAIN, &desc->flags); | 
 | 	if (lflags & GPIOHANDLE_REQUEST_OPEN_SOURCE) | 
 | 		set_bit(FLAG_OPEN_SOURCE, &desc->flags); | 
 |  | 
 | 	ret = gpiod_direction_input(desc); | 
 | 	if (ret) | 
 | 		goto out_free_desc; | 
 |  | 
 | 	le->irq = gpiod_to_irq(desc); | 
 | 	if (le->irq <= 0) { | 
 | 		ret = -ENODEV; | 
 | 		goto out_free_desc; | 
 | 	} | 
 |  | 
 | 	if (eflags & GPIOEVENT_REQUEST_RISING_EDGE) | 
 | 		irqflags |= IRQF_TRIGGER_RISING; | 
 | 	if (eflags & GPIOEVENT_REQUEST_FALLING_EDGE) | 
 | 		irqflags |= IRQF_TRIGGER_FALLING; | 
 | 	irqflags |= IRQF_ONESHOT; | 
 | 	irqflags |= IRQF_SHARED; | 
 |  | 
 | 	INIT_KFIFO(le->events); | 
 | 	init_waitqueue_head(&le->wait); | 
 | 	mutex_init(&le->read_lock); | 
 |  | 
 | 	/* Request a thread to read the events */ | 
 | 	ret = request_threaded_irq(le->irq, | 
 | 			NULL, | 
 | 			lineevent_irq_thread, | 
 | 			irqflags, | 
 | 			le->label, | 
 | 			le); | 
 | 	if (ret) | 
 | 		goto out_free_desc; | 
 |  | 
 | 	fd = get_unused_fd_flags(O_RDONLY | O_CLOEXEC); | 
 | 	if (fd < 0) { | 
 | 		ret = fd; | 
 | 		goto out_free_irq; | 
 | 	} | 
 |  | 
 | 	file = anon_inode_getfile("gpio-event", | 
 | 				  &lineevent_fileops, | 
 | 				  le, | 
 | 				  O_RDONLY | O_CLOEXEC); | 
 | 	if (IS_ERR(file)) { | 
 | 		ret = PTR_ERR(file); | 
 | 		goto out_put_unused_fd; | 
 | 	} | 
 |  | 
 | 	eventreq.fd = fd; | 
 | 	if (copy_to_user(ip, &eventreq, sizeof(eventreq))) { | 
 | 		/* | 
 | 		 * fput() will trigger the release() callback, so do not go onto | 
 | 		 * the regular error cleanup path here. | 
 | 		 */ | 
 | 		fput(file); | 
 | 		put_unused_fd(fd); | 
 | 		return -EFAULT; | 
 | 	} | 
 |  | 
 | 	fd_install(fd, file); | 
 |  | 
 | 	return 0; | 
 |  | 
 | out_put_unused_fd: | 
 | 	put_unused_fd(fd); | 
 | out_free_irq: | 
 | 	free_irq(le->irq, le); | 
 | out_free_desc: | 
 | 	gpiod_free(le->desc); | 
 | out_free_label: | 
 | 	kfree(le->label); | 
 | out_free_le: | 
 | 	kfree(le); | 
 | 	put_device(&gdev->dev); | 
 | 	return ret; | 
 | } | 
 |  | 
 | /** | 
 |  * gpio_ioctl() - ioctl handler for the GPIO chardev | 
 |  */ | 
 | static long gpio_ioctl(struct file *filp, unsigned int cmd, unsigned long arg) | 
 | { | 
 | 	struct gpio_device *gdev = filp->private_data; | 
 | 	struct gpio_chip *chip = gdev->chip; | 
 | 	void __user *ip = (void __user *)arg; | 
 |  | 
 | 	/* We fail any subsequent ioctl():s when the chip is gone */ | 
 | 	if (!chip) | 
 | 		return -ENODEV; | 
 |  | 
 | 	/* Fill in the struct and pass to userspace */ | 
 | 	if (cmd == GPIO_GET_CHIPINFO_IOCTL) { | 
 | 		struct gpiochip_info chipinfo; | 
 |  | 
 | 		memset(&chipinfo, 0, sizeof(chipinfo)); | 
 |  | 
 | 		strncpy(chipinfo.name, dev_name(&gdev->dev), | 
 | 			sizeof(chipinfo.name)); | 
 | 		chipinfo.name[sizeof(chipinfo.name)-1] = '\0'; | 
 | 		strncpy(chipinfo.label, gdev->label, | 
 | 			sizeof(chipinfo.label)); | 
 | 		chipinfo.label[sizeof(chipinfo.label)-1] = '\0'; | 
 | 		chipinfo.lines = gdev->ngpio; | 
 | 		if (copy_to_user(ip, &chipinfo, sizeof(chipinfo))) | 
 | 			return -EFAULT; | 
 | 		return 0; | 
 | 	} else if (cmd == GPIO_GET_LINEINFO_IOCTL) { | 
 | 		struct gpioline_info lineinfo; | 
 | 		struct gpio_desc *desc; | 
 |  | 
 | 		if (copy_from_user(&lineinfo, ip, sizeof(lineinfo))) | 
 | 			return -EFAULT; | 
 | 		if (lineinfo.line_offset >= gdev->ngpio) | 
 | 			return -EINVAL; | 
 |  | 
 | 		desc = &gdev->descs[lineinfo.line_offset]; | 
 | 		if (desc->name) { | 
 | 			strncpy(lineinfo.name, desc->name, | 
 | 				sizeof(lineinfo.name)); | 
 | 			lineinfo.name[sizeof(lineinfo.name)-1] = '\0'; | 
 | 		} else { | 
 | 			lineinfo.name[0] = '\0'; | 
 | 		} | 
 | 		if (desc->label) { | 
 | 			strncpy(lineinfo.consumer, desc->label, | 
 | 				sizeof(lineinfo.consumer)); | 
 | 			lineinfo.consumer[sizeof(lineinfo.consumer)-1] = '\0'; | 
 | 		} else { | 
 | 			lineinfo.consumer[0] = '\0'; | 
 | 		} | 
 |  | 
 | 		/* | 
 | 		 * Userspace only need to know that the kernel is using | 
 | 		 * this GPIO so it can't use it. | 
 | 		 */ | 
 | 		lineinfo.flags = 0; | 
 | 		if (test_bit(FLAG_REQUESTED, &desc->flags) || | 
 | 		    test_bit(FLAG_IS_HOGGED, &desc->flags) || | 
 | 		    test_bit(FLAG_USED_AS_IRQ, &desc->flags) || | 
 | 		    test_bit(FLAG_EXPORT, &desc->flags) || | 
 | 		    test_bit(FLAG_SYSFS, &desc->flags)) | 
 | 			lineinfo.flags |= GPIOLINE_FLAG_KERNEL; | 
 | 		if (test_bit(FLAG_IS_OUT, &desc->flags)) | 
 | 			lineinfo.flags |= GPIOLINE_FLAG_IS_OUT; | 
 | 		if (test_bit(FLAG_ACTIVE_LOW, &desc->flags)) | 
 | 			lineinfo.flags |= GPIOLINE_FLAG_ACTIVE_LOW; | 
 | 		if (test_bit(FLAG_OPEN_DRAIN, &desc->flags)) | 
 | 			lineinfo.flags |= GPIOLINE_FLAG_OPEN_DRAIN; | 
 | 		if (test_bit(FLAG_OPEN_SOURCE, &desc->flags)) | 
 | 			lineinfo.flags |= GPIOLINE_FLAG_OPEN_SOURCE; | 
 |  | 
 | 		if (copy_to_user(ip, &lineinfo, sizeof(lineinfo))) | 
 | 			return -EFAULT; | 
 | 		return 0; | 
 | 	} else if (cmd == GPIO_GET_LINEHANDLE_IOCTL) { | 
 | 		return linehandle_create(gdev, ip); | 
 | 	} else if (cmd == GPIO_GET_LINEEVENT_IOCTL) { | 
 | 		return lineevent_create(gdev, ip); | 
 | 	} | 
 | 	return -EINVAL; | 
 | } | 
 |  | 
 | #ifdef CONFIG_COMPAT | 
 | static long gpio_ioctl_compat(struct file *filp, unsigned int cmd, | 
 | 			      unsigned long arg) | 
 | { | 
 | 	return gpio_ioctl(filp, cmd, (unsigned long)compat_ptr(arg)); | 
 | } | 
 | #endif | 
 |  | 
 | /** | 
 |  * gpio_chrdev_open() - open the chardev for ioctl operations | 
 |  * @inode: inode for this chardev | 
 |  * @filp: file struct for storing private data | 
 |  * Returns 0 on success | 
 |  */ | 
 | static int gpio_chrdev_open(struct inode *inode, struct file *filp) | 
 | { | 
 | 	struct gpio_device *gdev = container_of(inode->i_cdev, | 
 | 					      struct gpio_device, chrdev); | 
 |  | 
 | 	/* Fail on open if the backing gpiochip is gone */ | 
 | 	if (!gdev->chip) | 
 | 		return -ENODEV; | 
 | 	get_device(&gdev->dev); | 
 | 	filp->private_data = gdev; | 
 |  | 
 | 	return nonseekable_open(inode, filp); | 
 | } | 
 |  | 
 | /** | 
 |  * gpio_chrdev_release() - close chardev after ioctl operations | 
 |  * @inode: inode for this chardev | 
 |  * @filp: file struct for storing private data | 
 |  * Returns 0 on success | 
 |  */ | 
 | static int gpio_chrdev_release(struct inode *inode, struct file *filp) | 
 | { | 
 | 	struct gpio_device *gdev = container_of(inode->i_cdev, | 
 | 					      struct gpio_device, chrdev); | 
 |  | 
 | 	put_device(&gdev->dev); | 
 | 	return 0; | 
 | } | 
 |  | 
 |  | 
 | static const struct file_operations gpio_fileops = { | 
 | 	.release = gpio_chrdev_release, | 
 | 	.open = gpio_chrdev_open, | 
 | 	.owner = THIS_MODULE, | 
 | 	.llseek = no_llseek, | 
 | 	.unlocked_ioctl = gpio_ioctl, | 
 | #ifdef CONFIG_COMPAT | 
 | 	.compat_ioctl = gpio_ioctl_compat, | 
 | #endif | 
 | }; | 
 |  | 
 | static void gpiodevice_release(struct device *dev) | 
 | { | 
 | 	struct gpio_device *gdev = dev_get_drvdata(dev); | 
 |  | 
 | 	list_del(&gdev->list); | 
 | 	ida_simple_remove(&gpio_ida, gdev->id); | 
 | 	kfree(gdev->label); | 
 | 	kfree(gdev->descs); | 
 | 	kfree(gdev); | 
 | } | 
 |  | 
 | static int gpiochip_setup_dev(struct gpio_device *gdev) | 
 | { | 
 | 	int status; | 
 |  | 
 | 	cdev_init(&gdev->chrdev, &gpio_fileops); | 
 | 	gdev->chrdev.owner = THIS_MODULE; | 
 | 	gdev->chrdev.kobj.parent = &gdev->dev.kobj; | 
 | 	gdev->dev.devt = MKDEV(MAJOR(gpio_devt), gdev->id); | 
 | 	status = cdev_add(&gdev->chrdev, gdev->dev.devt, 1); | 
 | 	if (status < 0) | 
 | 		chip_warn(gdev->chip, "failed to add char device %d:%d\n", | 
 | 			  MAJOR(gpio_devt), gdev->id); | 
 | 	else | 
 | 		chip_dbg(gdev->chip, "added GPIO chardev (%d:%d)\n", | 
 | 			 MAJOR(gpio_devt), gdev->id); | 
 | 	status = device_add(&gdev->dev); | 
 | 	if (status) | 
 | 		goto err_remove_chardev; | 
 |  | 
 | 	status = gpiochip_sysfs_register(gdev); | 
 | 	if (status) | 
 | 		goto err_remove_device; | 
 |  | 
 | 	/* From this point, the .release() function cleans up gpio_device */ | 
 | 	gdev->dev.release = gpiodevice_release; | 
 | 	pr_debug("%s: registered GPIOs %d to %d on device: %s (%s)\n", | 
 | 		 __func__, gdev->base, gdev->base + gdev->ngpio - 1, | 
 | 		 dev_name(&gdev->dev), gdev->chip->label ? : "generic"); | 
 |  | 
 | 	return 0; | 
 |  | 
 | err_remove_device: | 
 | 	device_del(&gdev->dev); | 
 | err_remove_chardev: | 
 | 	cdev_del(&gdev->chrdev); | 
 | 	return status; | 
 | } | 
 |  | 
 | static void gpiochip_setup_devs(void) | 
 | { | 
 | 	struct gpio_device *gdev; | 
 | 	int err; | 
 |  | 
 | 	list_for_each_entry(gdev, &gpio_devices, list) { | 
 | 		err = gpiochip_setup_dev(gdev); | 
 | 		if (err) | 
 | 			pr_err("%s: Failed to initialize gpio device (%d)\n", | 
 | 			       dev_name(&gdev->dev), err); | 
 | 	} | 
 | } | 
 |  | 
 | /** | 
 |  * gpiochip_add_data() - register a gpio_chip | 
 |  * @chip: the chip to register, with chip->base initialized | 
 |  * Context: potentially before irqs will work | 
 |  * | 
 |  * Returns a negative errno if the chip can't be registered, such as | 
 |  * because the chip->base is invalid or already associated with a | 
 |  * different chip.  Otherwise it returns zero as a success code. | 
 |  * | 
 |  * When gpiochip_add_data() is called very early during boot, so that GPIOs | 
 |  * can be freely used, the chip->parent device must be registered before | 
 |  * the gpio framework's arch_initcall().  Otherwise sysfs initialization | 
 |  * for GPIOs will fail rudely. | 
 |  * | 
 |  * gpiochip_add_data() must only be called after gpiolib initialization, | 
 |  * ie after core_initcall(). | 
 |  * | 
 |  * If chip->base is negative, this requests dynamic assignment of | 
 |  * a range of valid GPIOs. | 
 |  */ | 
 | int gpiochip_add_data(struct gpio_chip *chip, void *data) | 
 | { | 
 | 	unsigned long	flags; | 
 | 	int		status = 0; | 
 | 	unsigned	i; | 
 | 	int		base = chip->base; | 
 | 	struct gpio_device *gdev; | 
 |  | 
 | 	/* | 
 | 	 * First: allocate and populate the internal stat container, and | 
 | 	 * set up the struct device. | 
 | 	 */ | 
 | 	gdev = kzalloc(sizeof(*gdev), GFP_KERNEL); | 
 | 	if (!gdev) | 
 | 		return -ENOMEM; | 
 | 	gdev->dev.bus = &gpio_bus_type; | 
 | 	gdev->chip = chip; | 
 | 	chip->gpiodev = gdev; | 
 | 	if (chip->parent) { | 
 | 		gdev->dev.parent = chip->parent; | 
 | 		gdev->dev.of_node = chip->parent->of_node; | 
 | 	} | 
 |  | 
 | #ifdef CONFIG_OF_GPIO | 
 | 	/* If the gpiochip has an assigned OF node this takes precedence */ | 
 | 	if (chip->of_node) | 
 | 		gdev->dev.of_node = chip->of_node; | 
 | #endif | 
 |  | 
 | 	gdev->id = ida_simple_get(&gpio_ida, 0, 0, GFP_KERNEL); | 
 | 	if (gdev->id < 0) { | 
 | 		status = gdev->id; | 
 | 		goto err_free_gdev; | 
 | 	} | 
 | 	dev_set_name(&gdev->dev, "gpiochip%d", gdev->id); | 
 | 	device_initialize(&gdev->dev); | 
 | 	dev_set_drvdata(&gdev->dev, gdev); | 
 | 	if (chip->parent && chip->parent->driver) | 
 | 		gdev->owner = chip->parent->driver->owner; | 
 | 	else if (chip->owner) | 
 | 		/* TODO: remove chip->owner */ | 
 | 		gdev->owner = chip->owner; | 
 | 	else | 
 | 		gdev->owner = THIS_MODULE; | 
 |  | 
 | 	gdev->descs = kcalloc(chip->ngpio, sizeof(gdev->descs[0]), GFP_KERNEL); | 
 | 	if (!gdev->descs) { | 
 | 		status = -ENOMEM; | 
 | 		goto err_free_gdev; | 
 | 	} | 
 |  | 
 | 	if (chip->ngpio == 0) { | 
 | 		chip_err(chip, "tried to insert a GPIO chip with zero lines\n"); | 
 | 		status = -EINVAL; | 
 | 		goto err_free_descs; | 
 | 	} | 
 |  | 
 | 	if (chip->label) | 
 | 		gdev->label = kstrdup(chip->label, GFP_KERNEL); | 
 | 	else | 
 | 		gdev->label = kstrdup("unknown", GFP_KERNEL); | 
 | 	if (!gdev->label) { | 
 | 		status = -ENOMEM; | 
 | 		goto err_free_descs; | 
 | 	} | 
 |  | 
 | 	gdev->ngpio = chip->ngpio; | 
 | 	gdev->data = data; | 
 |  | 
 | 	spin_lock_irqsave(&gpio_lock, flags); | 
 |  | 
 | 	/* | 
 | 	 * TODO: this allocates a Linux GPIO number base in the global | 
 | 	 * GPIO numberspace for this chip. In the long run we want to | 
 | 	 * get *rid* of this numberspace and use only descriptors, but | 
 | 	 * it may be a pipe dream. It will not happen before we get rid | 
 | 	 * of the sysfs interface anyways. | 
 | 	 */ | 
 | 	if (base < 0) { | 
 | 		base = gpiochip_find_base(chip->ngpio); | 
 | 		if (base < 0) { | 
 | 			status = base; | 
 | 			spin_unlock_irqrestore(&gpio_lock, flags); | 
 | 			goto err_free_label; | 
 | 		} | 
 | 		/* | 
 | 		 * TODO: it should not be necessary to reflect the assigned | 
 | 		 * base outside of the GPIO subsystem. Go over drivers and | 
 | 		 * see if anyone makes use of this, else drop this and assign | 
 | 		 * a poison instead. | 
 | 		 */ | 
 | 		chip->base = base; | 
 | 	} | 
 | 	gdev->base = base; | 
 |  | 
 | 	status = gpiodev_add_to_list(gdev); | 
 | 	if (status) { | 
 | 		spin_unlock_irqrestore(&gpio_lock, flags); | 
 | 		goto err_free_label; | 
 | 	} | 
 |  | 
 | 	spin_unlock_irqrestore(&gpio_lock, flags); | 
 |  | 
 | 	for (i = 0; i < chip->ngpio; i++) { | 
 | 		struct gpio_desc *desc = &gdev->descs[i]; | 
 |  | 
 | 		desc->gdev = gdev; | 
 | 		/* | 
 | 		 * REVISIT: most hardware initializes GPIOs as inputs | 
 | 		 * (often with pullups enabled) so power usage is | 
 | 		 * minimized. Linux code should set the gpio direction | 
 | 		 * first thing; but until it does, and in case | 
 | 		 * chip->get_direction is not set, we may expose the | 
 | 		 * wrong direction in sysfs. | 
 | 		 */ | 
 |  | 
 | 		if (chip->get_direction) { | 
 | 			/* | 
 | 			 * If we have .get_direction, set up the initial | 
 | 			 * direction flag from the hardware. | 
 | 			 */ | 
 | 			int dir = chip->get_direction(chip, i); | 
 |  | 
 | 			if (!dir) | 
 | 				set_bit(FLAG_IS_OUT, &desc->flags); | 
 | 		} else if (!chip->direction_input) { | 
 | 			/* | 
 | 			 * If the chip lacks the .direction_input callback | 
 | 			 * we logically assume all lines are outputs. | 
 | 			 */ | 
 | 			set_bit(FLAG_IS_OUT, &desc->flags); | 
 | 		} | 
 | 	} | 
 |  | 
 | #ifdef CONFIG_PINCTRL | 
 | 	INIT_LIST_HEAD(&gdev->pin_ranges); | 
 | #endif | 
 |  | 
 | 	status = gpiochip_set_desc_names(chip); | 
 | 	if (status) | 
 | 		goto err_remove_from_list; | 
 |  | 
 | 	status = gpiochip_irqchip_init_valid_mask(chip); | 
 | 	if (status) | 
 | 		goto err_remove_from_list; | 
 |  | 
 | 	status = of_gpiochip_add(chip); | 
 | 	if (status) | 
 | 		goto err_remove_chip; | 
 |  | 
 | 	acpi_gpiochip_add(chip); | 
 |  | 
 | 	/* | 
 | 	 * By first adding the chardev, and then adding the device, | 
 | 	 * we get a device node entry in sysfs under | 
 | 	 * /sys/bus/gpio/devices/gpiochipN/dev that can be used for | 
 | 	 * coldplug of device nodes and other udev business. | 
 | 	 * We can do this only if gpiolib has been initialized. | 
 | 	 * Otherwise, defer until later. | 
 | 	 */ | 
 | 	if (gpiolib_initialized) { | 
 | 		status = gpiochip_setup_dev(gdev); | 
 | 		if (status) | 
 | 			goto err_remove_chip; | 
 | 	} | 
 | 	return 0; | 
 |  | 
 | err_remove_chip: | 
 | 	acpi_gpiochip_remove(chip); | 
 | 	gpiochip_free_hogs(chip); | 
 | 	of_gpiochip_remove(chip); | 
 | 	gpiochip_irqchip_free_valid_mask(chip); | 
 | err_remove_from_list: | 
 | 	spin_lock_irqsave(&gpio_lock, flags); | 
 | 	list_del(&gdev->list); | 
 | 	spin_unlock_irqrestore(&gpio_lock, flags); | 
 | err_free_label: | 
 | 	kfree(gdev->label); | 
 | err_free_descs: | 
 | 	kfree(gdev->descs); | 
 | err_free_gdev: | 
 | 	ida_simple_remove(&gpio_ida, gdev->id); | 
 | 	/* failures here can mean systems won't boot... */ | 
 | 	pr_err("%s: GPIOs %d..%d (%s) failed to register\n", __func__, | 
 | 	       gdev->base, gdev->base + gdev->ngpio - 1, | 
 | 	       chip->label ? : "generic"); | 
 | 	kfree(gdev); | 
 | 	return status; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_add_data); | 
 |  | 
 | /** | 
 |  * gpiochip_get_data() - get per-subdriver data for the chip | 
 |  */ | 
 | void *gpiochip_get_data(struct gpio_chip *chip) | 
 | { | 
 | 	return chip->gpiodev->data; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_get_data); | 
 |  | 
 | /** | 
 |  * gpiochip_remove() - unregister a gpio_chip | 
 |  * @chip: the chip to unregister | 
 |  * | 
 |  * A gpio_chip with any GPIOs still requested may not be removed. | 
 |  */ | 
 | void gpiochip_remove(struct gpio_chip *chip) | 
 | { | 
 | 	struct gpio_device *gdev = chip->gpiodev; | 
 | 	struct gpio_desc *desc; | 
 | 	unsigned long	flags; | 
 | 	unsigned	i; | 
 | 	bool		requested = false; | 
 |  | 
 | 	/* FIXME: should the legacy sysfs handling be moved to gpio_device? */ | 
 | 	gpiochip_sysfs_unregister(gdev); | 
 | 	gpiochip_free_hogs(chip); | 
 | 	/* Numb the device, cancelling all outstanding operations */ | 
 | 	gdev->chip = NULL; | 
 | 	gpiochip_irqchip_remove(chip); | 
 | 	acpi_gpiochip_remove(chip); | 
 | 	gpiochip_remove_pin_ranges(chip); | 
 | 	of_gpiochip_remove(chip); | 
 | 	/* | 
 | 	 * We accept no more calls into the driver from this point, so | 
 | 	 * NULL the driver data pointer | 
 | 	 */ | 
 | 	gdev->data = NULL; | 
 |  | 
 | 	spin_lock_irqsave(&gpio_lock, flags); | 
 | 	for (i = 0; i < gdev->ngpio; i++) { | 
 | 		desc = &gdev->descs[i]; | 
 | 		if (test_bit(FLAG_REQUESTED, &desc->flags)) | 
 | 			requested = true; | 
 | 	} | 
 | 	spin_unlock_irqrestore(&gpio_lock, flags); | 
 |  | 
 | 	if (requested) | 
 | 		dev_crit(&gdev->dev, | 
 | 			 "REMOVING GPIOCHIP WITH GPIOS STILL REQUESTED\n"); | 
 |  | 
 | 	/* | 
 | 	 * The gpiochip side puts its use of the device to rest here: | 
 | 	 * if there are no userspace clients, the chardev and device will | 
 | 	 * be removed, else it will be dangling until the last user is | 
 | 	 * gone. | 
 | 	 */ | 
 | 	cdev_del(&gdev->chrdev); | 
 | 	device_del(&gdev->dev); | 
 | 	put_device(&gdev->dev); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_remove); | 
 |  | 
 | static void devm_gpio_chip_release(struct device *dev, void *res) | 
 | { | 
 | 	struct gpio_chip *chip = *(struct gpio_chip **)res; | 
 |  | 
 | 	gpiochip_remove(chip); | 
 | } | 
 |  | 
 | static int devm_gpio_chip_match(struct device *dev, void *res, void *data) | 
 |  | 
 | { | 
 | 	struct gpio_chip **r = res; | 
 |  | 
 | 	if (!r || !*r) { | 
 | 		WARN_ON(!r || !*r); | 
 | 		return 0; | 
 | 	} | 
 |  | 
 | 	return *r == data; | 
 | } | 
 |  | 
 | /** | 
 |  * devm_gpiochip_add_data() - Resource manager piochip_add_data() | 
 |  * @dev: the device pointer on which irq_chip belongs to. | 
 |  * @chip: the chip to register, with chip->base initialized | 
 |  * Context: potentially before irqs will work | 
 |  * | 
 |  * Returns a negative errno if the chip can't be registered, such as | 
 |  * because the chip->base is invalid or already associated with a | 
 |  * different chip.  Otherwise it returns zero as a success code. | 
 |  * | 
 |  * The gpio chip automatically be released when the device is unbound. | 
 |  */ | 
 | int devm_gpiochip_add_data(struct device *dev, struct gpio_chip *chip, | 
 | 			   void *data) | 
 | { | 
 | 	struct gpio_chip **ptr; | 
 | 	int ret; | 
 |  | 
 | 	ptr = devres_alloc(devm_gpio_chip_release, sizeof(*ptr), | 
 | 			     GFP_KERNEL); | 
 | 	if (!ptr) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	ret = gpiochip_add_data(chip, data); | 
 | 	if (ret < 0) { | 
 | 		devres_free(ptr); | 
 | 		return ret; | 
 | 	} | 
 |  | 
 | 	*ptr = chip; | 
 | 	devres_add(dev, ptr); | 
 |  | 
 | 	return 0; | 
 | } | 
 | EXPORT_SYMBOL_GPL(devm_gpiochip_add_data); | 
 |  | 
 | /** | 
 |  * devm_gpiochip_remove() - Resource manager of gpiochip_remove() | 
 |  * @dev: device for which which resource was allocated | 
 |  * @chip: the chip to remove | 
 |  * | 
 |  * A gpio_chip with any GPIOs still requested may not be removed. | 
 |  */ | 
 | void devm_gpiochip_remove(struct device *dev, struct gpio_chip *chip) | 
 | { | 
 | 	int ret; | 
 |  | 
 | 	ret = devres_release(dev, devm_gpio_chip_release, | 
 | 			     devm_gpio_chip_match, chip); | 
 | 	WARN_ON(ret); | 
 | } | 
 | EXPORT_SYMBOL_GPL(devm_gpiochip_remove); | 
 |  | 
 | /** | 
 |  * gpiochip_find() - iterator for locating a specific gpio_chip | 
 |  * @data: data to pass to match function | 
 |  * @callback: Callback function to check gpio_chip | 
 |  * | 
 |  * Similar to bus_find_device.  It returns a reference to a gpio_chip as | 
 |  * determined by a user supplied @match callback.  The callback should return | 
 |  * 0 if the device doesn't match and non-zero if it does.  If the callback is | 
 |  * non-zero, this function will return to the caller and not iterate over any | 
 |  * more gpio_chips. | 
 |  */ | 
 | struct gpio_chip *gpiochip_find(void *data, | 
 | 				int (*match)(struct gpio_chip *chip, | 
 | 					     void *data)) | 
 | { | 
 | 	struct gpio_device *gdev; | 
 | 	struct gpio_chip *chip = NULL; | 
 | 	unsigned long flags; | 
 |  | 
 | 	spin_lock_irqsave(&gpio_lock, flags); | 
 | 	list_for_each_entry(gdev, &gpio_devices, list) | 
 | 		if (gdev->chip && match(gdev->chip, data)) { | 
 | 			chip = gdev->chip; | 
 | 			break; | 
 | 		} | 
 |  | 
 | 	spin_unlock_irqrestore(&gpio_lock, flags); | 
 |  | 
 | 	return chip; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_find); | 
 |  | 
 | static int gpiochip_match_name(struct gpio_chip *chip, void *data) | 
 | { | 
 | 	const char *name = data; | 
 |  | 
 | 	return !strcmp(chip->label, name); | 
 | } | 
 |  | 
 | static struct gpio_chip *find_chip_by_name(const char *name) | 
 | { | 
 | 	return gpiochip_find((void *)name, gpiochip_match_name); | 
 | } | 
 |  | 
 | #ifdef CONFIG_GPIOLIB_IRQCHIP | 
 |  | 
 | /* | 
 |  * The following is irqchip helper code for gpiochips. | 
 |  */ | 
 |  | 
 | static int gpiochip_irqchip_init_valid_mask(struct gpio_chip *gpiochip) | 
 | { | 
 | 	int i; | 
 |  | 
 | 	if (!gpiochip->irq_need_valid_mask) | 
 | 		return 0; | 
 |  | 
 | 	gpiochip->irq_valid_mask = kcalloc(BITS_TO_LONGS(gpiochip->ngpio), | 
 | 					   sizeof(long), GFP_KERNEL); | 
 | 	if (!gpiochip->irq_valid_mask) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	/* Assume by default all GPIOs are valid */ | 
 | 	for (i = 0; i < gpiochip->ngpio; i++) | 
 | 		set_bit(i, gpiochip->irq_valid_mask); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static void gpiochip_irqchip_free_valid_mask(struct gpio_chip *gpiochip) | 
 | { | 
 | 	kfree(gpiochip->irq_valid_mask); | 
 | 	gpiochip->irq_valid_mask = NULL; | 
 | } | 
 |  | 
 | static bool gpiochip_irqchip_irq_valid(const struct gpio_chip *gpiochip, | 
 | 				       unsigned int offset) | 
 | { | 
 | 	/* No mask means all valid */ | 
 | 	if (likely(!gpiochip->irq_valid_mask)) | 
 | 		return true; | 
 | 	return test_bit(offset, gpiochip->irq_valid_mask); | 
 | } | 
 |  | 
 | /** | 
 |  * gpiochip_set_cascaded_irqchip() - connects a cascaded irqchip to a gpiochip | 
 |  * @gpiochip: the gpiochip to set the irqchip chain to | 
 |  * @irqchip: the irqchip to chain to the gpiochip | 
 |  * @parent_irq: the irq number corresponding to the parent IRQ for this | 
 |  * chained irqchip | 
 |  * @parent_handler: the parent interrupt handler for the accumulated IRQ | 
 |  * coming out of the gpiochip. If the interrupt is nested rather than | 
 |  * cascaded, pass NULL in this handler argument | 
 |  */ | 
 | static void gpiochip_set_cascaded_irqchip(struct gpio_chip *gpiochip, | 
 | 					  struct irq_chip *irqchip, | 
 | 					  int parent_irq, | 
 | 					  irq_flow_handler_t parent_handler) | 
 | { | 
 | 	unsigned int offset; | 
 |  | 
 | 	if (!gpiochip->irqdomain) { | 
 | 		chip_err(gpiochip, "called %s before setting up irqchip\n", | 
 | 			 __func__); | 
 | 		return; | 
 | 	} | 
 |  | 
 | 	if (parent_handler) { | 
 | 		if (gpiochip->can_sleep) { | 
 | 			chip_err(gpiochip, | 
 | 				 "you cannot have chained interrupts on a " | 
 | 				 "chip that may sleep\n"); | 
 | 			return; | 
 | 		} | 
 | 		/* | 
 | 		 * The parent irqchip is already using the chip_data for this | 
 | 		 * irqchip, so our callbacks simply use the handler_data. | 
 | 		 */ | 
 | 		irq_set_chained_handler_and_data(parent_irq, parent_handler, | 
 | 						 gpiochip); | 
 |  | 
 | 		gpiochip->irq_chained_parent = parent_irq; | 
 | 	} | 
 |  | 
 | 	/* Set the parent IRQ for all affected IRQs */ | 
 | 	for (offset = 0; offset < gpiochip->ngpio; offset++) { | 
 | 		if (!gpiochip_irqchip_irq_valid(gpiochip, offset)) | 
 | 			continue; | 
 | 		irq_set_parent(irq_find_mapping(gpiochip->irqdomain, offset), | 
 | 			       parent_irq); | 
 | 	} | 
 | } | 
 |  | 
 | /** | 
 |  * gpiochip_set_chained_irqchip() - connects a chained irqchip to a gpiochip | 
 |  * @gpiochip: the gpiochip to set the irqchip chain to | 
 |  * @irqchip: the irqchip to chain to the gpiochip | 
 |  * @parent_irq: the irq number corresponding to the parent IRQ for this | 
 |  * chained irqchip | 
 |  * @parent_handler: the parent interrupt handler for the accumulated IRQ | 
 |  * coming out of the gpiochip. If the interrupt is nested rather than | 
 |  * cascaded, pass NULL in this handler argument | 
 |  */ | 
 | void gpiochip_set_chained_irqchip(struct gpio_chip *gpiochip, | 
 | 				  struct irq_chip *irqchip, | 
 | 				  int parent_irq, | 
 | 				  irq_flow_handler_t parent_handler) | 
 | { | 
 | 	gpiochip_set_cascaded_irqchip(gpiochip, irqchip, parent_irq, | 
 | 				      parent_handler); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_set_chained_irqchip); | 
 |  | 
 | /** | 
 |  * gpiochip_set_nested_irqchip() - connects a nested irqchip to a gpiochip | 
 |  * @gpiochip: the gpiochip to set the irqchip nested handler to | 
 |  * @irqchip: the irqchip to nest to the gpiochip | 
 |  * @parent_irq: the irq number corresponding to the parent IRQ for this | 
 |  * nested irqchip | 
 |  */ | 
 | void gpiochip_set_nested_irqchip(struct gpio_chip *gpiochip, | 
 | 				 struct irq_chip *irqchip, | 
 | 				 int parent_irq) | 
 | { | 
 | 	if (!gpiochip->irq_nested) { | 
 | 		chip_err(gpiochip, "tried to nest a chained gpiochip\n"); | 
 | 		return; | 
 | 	} | 
 | 	gpiochip_set_cascaded_irqchip(gpiochip, irqchip, parent_irq, | 
 | 				      NULL); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_set_nested_irqchip); | 
 |  | 
 | /** | 
 |  * gpiochip_irq_map() - maps an IRQ into a GPIO irqchip | 
 |  * @d: the irqdomain used by this irqchip | 
 |  * @irq: the global irq number used by this GPIO irqchip irq | 
 |  * @hwirq: the local IRQ/GPIO line offset on this gpiochip | 
 |  * | 
 |  * This function will set up the mapping for a certain IRQ line on a | 
 |  * gpiochip by assigning the gpiochip as chip data, and using the irqchip | 
 |  * stored inside the gpiochip. | 
 |  */ | 
 | static int gpiochip_irq_map(struct irq_domain *d, unsigned int irq, | 
 | 			    irq_hw_number_t hwirq) | 
 | { | 
 | 	struct gpio_chip *chip = d->host_data; | 
 |  | 
 | 	irq_set_chip_data(irq, chip); | 
 | 	/* | 
 | 	 * This lock class tells lockdep that GPIO irqs are in a different | 
 | 	 * category than their parents, so it won't report false recursion. | 
 | 	 */ | 
 | 	irq_set_lockdep_class(irq, chip->lock_key); | 
 | 	irq_set_chip_and_handler(irq, chip->irqchip, chip->irq_handler); | 
 | 	/* Chips that use nested thread handlers have them marked */ | 
 | 	if (chip->irq_nested) | 
 | 		irq_set_nested_thread(irq, 1); | 
 | 	irq_set_noprobe(irq); | 
 |  | 
 | 	/* | 
 | 	 * No set-up of the hardware will happen if IRQ_TYPE_NONE | 
 | 	 * is passed as default type. | 
 | 	 */ | 
 | 	if (chip->irq_default_type != IRQ_TYPE_NONE) | 
 | 		irq_set_irq_type(irq, chip->irq_default_type); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static void gpiochip_irq_unmap(struct irq_domain *d, unsigned int irq) | 
 | { | 
 | 	struct gpio_chip *chip = d->host_data; | 
 |  | 
 | 	if (chip->irq_nested) | 
 | 		irq_set_nested_thread(irq, 0); | 
 | 	irq_set_chip_and_handler(irq, NULL, NULL); | 
 | 	irq_set_chip_data(irq, NULL); | 
 | } | 
 |  | 
 | static const struct irq_domain_ops gpiochip_domain_ops = { | 
 | 	.map	= gpiochip_irq_map, | 
 | 	.unmap	= gpiochip_irq_unmap, | 
 | 	/* Virtually all GPIO irqchips are twocell:ed */ | 
 | 	.xlate	= irq_domain_xlate_twocell, | 
 | }; | 
 |  | 
 | static int gpiochip_irq_reqres(struct irq_data *d) | 
 | { | 
 | 	struct gpio_chip *chip = irq_data_get_irq_chip_data(d); | 
 |  | 
 | 	if (!try_module_get(chip->gpiodev->owner)) | 
 | 		return -ENODEV; | 
 |  | 
 | 	if (gpiochip_lock_as_irq(chip, d->hwirq)) { | 
 | 		chip_err(chip, | 
 | 			"unable to lock HW IRQ %lu for IRQ\n", | 
 | 			d->hwirq); | 
 | 		module_put(chip->gpiodev->owner); | 
 | 		return -EINVAL; | 
 | 	} | 
 | 	return 0; | 
 | } | 
 |  | 
 | static void gpiochip_irq_relres(struct irq_data *d) | 
 | { | 
 | 	struct gpio_chip *chip = irq_data_get_irq_chip_data(d); | 
 |  | 
 | 	gpiochip_unlock_as_irq(chip, d->hwirq); | 
 | 	module_put(chip->gpiodev->owner); | 
 | } | 
 |  | 
 | static int gpiochip_to_irq(struct gpio_chip *chip, unsigned offset) | 
 | { | 
 | 	return irq_find_mapping(chip->irqdomain, offset); | 
 | } | 
 |  | 
 | /** | 
 |  * gpiochip_irqchip_remove() - removes an irqchip added to a gpiochip | 
 |  * @gpiochip: the gpiochip to remove the irqchip from | 
 |  * | 
 |  * This is called only from gpiochip_remove() | 
 |  */ | 
 | static void gpiochip_irqchip_remove(struct gpio_chip *gpiochip) | 
 | { | 
 | 	unsigned int offset; | 
 |  | 
 | 	acpi_gpiochip_free_interrupts(gpiochip); | 
 |  | 
 | 	if (gpiochip->irq_chained_parent) { | 
 | 		irq_set_chained_handler(gpiochip->irq_chained_parent, NULL); | 
 | 		irq_set_handler_data(gpiochip->irq_chained_parent, NULL); | 
 | 	} | 
 |  | 
 | 	/* Remove all IRQ mappings and delete the domain */ | 
 | 	if (gpiochip->irqdomain) { | 
 | 		for (offset = 0; offset < gpiochip->ngpio; offset++) { | 
 | 			if (!gpiochip_irqchip_irq_valid(gpiochip, offset)) | 
 | 				continue; | 
 | 			irq_dispose_mapping( | 
 | 				irq_find_mapping(gpiochip->irqdomain, offset)); | 
 | 		} | 
 | 		irq_domain_remove(gpiochip->irqdomain); | 
 | 	} | 
 |  | 
 | 	if (gpiochip->irqchip) { | 
 | 		gpiochip->irqchip->irq_request_resources = NULL; | 
 | 		gpiochip->irqchip->irq_release_resources = NULL; | 
 | 		gpiochip->irqchip = NULL; | 
 | 	} | 
 |  | 
 | 	gpiochip_irqchip_free_valid_mask(gpiochip); | 
 | } | 
 |  | 
 | /** | 
 |  * gpiochip_irqchip_add_key() - adds an irqchip to a gpiochip | 
 |  * @gpiochip: the gpiochip to add the irqchip to | 
 |  * @irqchip: the irqchip to add to the gpiochip | 
 |  * @first_irq: if not dynamically assigned, the base (first) IRQ to | 
 |  * allocate gpiochip irqs from | 
 |  * @handler: the irq handler to use (often a predefined irq core function) | 
 |  * @type: the default type for IRQs on this irqchip, pass IRQ_TYPE_NONE | 
 |  * to have the core avoid setting up any default type in the hardware. | 
 |  * @nested: whether this is a nested irqchip calling handle_nested_irq() | 
 |  * in its IRQ handler | 
 |  * @lock_key: lockdep class | 
 |  * | 
 |  * This function closely associates a certain irqchip with a certain | 
 |  * gpiochip, providing an irq domain to translate the local IRQs to | 
 |  * global irqs in the gpiolib core, and making sure that the gpiochip | 
 |  * is passed as chip data to all related functions. Driver callbacks | 
 |  * need to use gpiochip_get_data() to get their local state containers back | 
 |  * from the gpiochip passed as chip data. An irqdomain will be stored | 
 |  * in the gpiochip that shall be used by the driver to handle IRQ number | 
 |  * translation. The gpiochip will need to be initialized and registered | 
 |  * before calling this function. | 
 |  * | 
 |  * This function will handle two cell:ed simple IRQs and assumes all | 
 |  * the pins on the gpiochip can generate a unique IRQ. Everything else | 
 |  * need to be open coded. | 
 |  */ | 
 | int gpiochip_irqchip_add_key(struct gpio_chip *gpiochip, | 
 | 			     struct irq_chip *irqchip, | 
 | 			     unsigned int first_irq, | 
 | 			     irq_flow_handler_t handler, | 
 | 			     unsigned int type, | 
 | 			     bool nested, | 
 | 			     struct lock_class_key *lock_key) | 
 | { | 
 | 	struct device_node *of_node; | 
 | 	bool irq_base_set = false; | 
 | 	unsigned int offset; | 
 | 	unsigned irq_base = 0; | 
 |  | 
 | 	if (!gpiochip || !irqchip) | 
 | 		return -EINVAL; | 
 |  | 
 | 	if (!gpiochip->parent) { | 
 | 		pr_err("missing gpiochip .dev parent pointer\n"); | 
 | 		return -EINVAL; | 
 | 	} | 
 | 	gpiochip->irq_nested = nested; | 
 | 	of_node = gpiochip->parent->of_node; | 
 | #ifdef CONFIG_OF_GPIO | 
 | 	/* | 
 | 	 * If the gpiochip has an assigned OF node this takes precedence | 
 | 	 * FIXME: get rid of this and use gpiochip->parent->of_node | 
 | 	 * everywhere | 
 | 	 */ | 
 | 	if (gpiochip->of_node) | 
 | 		of_node = gpiochip->of_node; | 
 | #endif | 
 | 	/* | 
 | 	 * Specifying a default trigger is a terrible idea if DT or ACPI is | 
 | 	 * used to configure the interrupts, as you may end-up with | 
 | 	 * conflicting triggers. Tell the user, and reset to NONE. | 
 | 	 */ | 
 | 	if (WARN(of_node && type != IRQ_TYPE_NONE, | 
 | 		 "%s: Ignoring %d default trigger\n", of_node->full_name, type)) | 
 | 		type = IRQ_TYPE_NONE; | 
 | 	if (has_acpi_companion(gpiochip->parent) && type != IRQ_TYPE_NONE) { | 
 | 		acpi_handle_warn(ACPI_HANDLE(gpiochip->parent), | 
 | 				 "Ignoring %d default trigger\n", type); | 
 | 		type = IRQ_TYPE_NONE; | 
 | 	} | 
 |  | 
 | 	gpiochip->irqchip = irqchip; | 
 | 	gpiochip->irq_handler = handler; | 
 | 	gpiochip->irq_default_type = type; | 
 | 	gpiochip->to_irq = gpiochip_to_irq; | 
 | 	gpiochip->lock_key = lock_key; | 
 | 	gpiochip->irqdomain = irq_domain_add_simple(of_node, | 
 | 					gpiochip->ngpio, first_irq, | 
 | 					&gpiochip_domain_ops, gpiochip); | 
 | 	if (!gpiochip->irqdomain) { | 
 | 		gpiochip->irqchip = NULL; | 
 | 		return -EINVAL; | 
 | 	} | 
 |  | 
 | 	/* | 
 | 	 * It is possible for a driver to override this, but only if the | 
 | 	 * alternative functions are both implemented. | 
 | 	 */ | 
 | 	if (!irqchip->irq_request_resources && | 
 | 	    !irqchip->irq_release_resources) { | 
 | 		irqchip->irq_request_resources = gpiochip_irq_reqres; | 
 | 		irqchip->irq_release_resources = gpiochip_irq_relres; | 
 | 	} | 
 |  | 
 | 	/* | 
 | 	 * Prepare the mapping since the irqchip shall be orthogonal to | 
 | 	 * any gpiochip calls. If the first_irq was zero, this is | 
 | 	 * necessary to allocate descriptors for all IRQs. | 
 | 	 */ | 
 | 	for (offset = 0; offset < gpiochip->ngpio; offset++) { | 
 | 		if (!gpiochip_irqchip_irq_valid(gpiochip, offset)) | 
 | 			continue; | 
 | 		irq_base = irq_create_mapping(gpiochip->irqdomain, offset); | 
 | 		if (!irq_base_set) { | 
 | 			/* | 
 | 			 * Store the base into the gpiochip to be used when | 
 | 			 * unmapping the irqs. | 
 | 			 */ | 
 | 			gpiochip->irq_base = irq_base; | 
 | 			irq_base_set = true; | 
 | 		} | 
 | 	} | 
 |  | 
 | 	acpi_gpiochip_request_interrupts(gpiochip); | 
 |  | 
 | 	return 0; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_irqchip_add_key); | 
 |  | 
 | #else /* CONFIG_GPIOLIB_IRQCHIP */ | 
 |  | 
 | static void gpiochip_irqchip_remove(struct gpio_chip *gpiochip) {} | 
 | static inline int gpiochip_irqchip_init_valid_mask(struct gpio_chip *gpiochip) | 
 | { | 
 | 	return 0; | 
 | } | 
 | static inline void gpiochip_irqchip_free_valid_mask(struct gpio_chip *gpiochip) | 
 | { } | 
 |  | 
 | #endif /* CONFIG_GPIOLIB_IRQCHIP */ | 
 |  | 
 | /** | 
 |  * gpiochip_generic_request() - request the gpio function for a pin | 
 |  * @chip: the gpiochip owning the GPIO | 
 |  * @offset: the offset of the GPIO to request for GPIO function | 
 |  */ | 
 | int gpiochip_generic_request(struct gpio_chip *chip, unsigned offset) | 
 | { | 
 | 	return pinctrl_request_gpio(chip->gpiodev->base + offset); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_generic_request); | 
 |  | 
 | /** | 
 |  * gpiochip_generic_free() - free the gpio function from a pin | 
 |  * @chip: the gpiochip to request the gpio function for | 
 |  * @offset: the offset of the GPIO to free from GPIO function | 
 |  */ | 
 | void gpiochip_generic_free(struct gpio_chip *chip, unsigned offset) | 
 | { | 
 | 	pinctrl_free_gpio(chip->gpiodev->base + offset); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_generic_free); | 
 |  | 
 | /** | 
 |  * gpiochip_generic_config() - apply configuration for a pin | 
 |  * @chip: the gpiochip owning the GPIO | 
 |  * @offset: the offset of the GPIO to apply the configuration | 
 |  * @config: the configuration to be applied | 
 |  */ | 
 | int gpiochip_generic_config(struct gpio_chip *chip, unsigned offset, | 
 | 			    unsigned long config) | 
 | { | 
 | 	return pinctrl_gpio_set_config(chip->gpiodev->base + offset, config); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_generic_config); | 
 |  | 
 | #ifdef CONFIG_PINCTRL | 
 |  | 
 | /** | 
 |  * gpiochip_add_pingroup_range() - add a range for GPIO <-> pin mapping | 
 |  * @chip: the gpiochip to add the range for | 
 |  * @pctldev: the pin controller to map to | 
 |  * @gpio_offset: the start offset in the current gpio_chip number space | 
 |  * @pin_group: name of the pin group inside the pin controller | 
 |  */ | 
 | int gpiochip_add_pingroup_range(struct gpio_chip *chip, | 
 | 			struct pinctrl_dev *pctldev, | 
 | 			unsigned int gpio_offset, const char *pin_group) | 
 | { | 
 | 	struct gpio_pin_range *pin_range; | 
 | 	struct gpio_device *gdev = chip->gpiodev; | 
 | 	int ret; | 
 |  | 
 | 	pin_range = kzalloc(sizeof(*pin_range), GFP_KERNEL); | 
 | 	if (!pin_range) { | 
 | 		chip_err(chip, "failed to allocate pin ranges\n"); | 
 | 		return -ENOMEM; | 
 | 	} | 
 |  | 
 | 	/* Use local offset as range ID */ | 
 | 	pin_range->range.id = gpio_offset; | 
 | 	pin_range->range.gc = chip; | 
 | 	pin_range->range.name = chip->label; | 
 | 	pin_range->range.base = gdev->base + gpio_offset; | 
 | 	pin_range->pctldev = pctldev; | 
 |  | 
 | 	ret = pinctrl_get_group_pins(pctldev, pin_group, | 
 | 					&pin_range->range.pins, | 
 | 					&pin_range->range.npins); | 
 | 	if (ret < 0) { | 
 | 		kfree(pin_range); | 
 | 		return ret; | 
 | 	} | 
 |  | 
 | 	pinctrl_add_gpio_range(pctldev, &pin_range->range); | 
 |  | 
 | 	chip_dbg(chip, "created GPIO range %d->%d ==> %s PINGRP %s\n", | 
 | 		 gpio_offset, gpio_offset + pin_range->range.npins - 1, | 
 | 		 pinctrl_dev_get_devname(pctldev), pin_group); | 
 |  | 
 | 	list_add_tail(&pin_range->node, &gdev->pin_ranges); | 
 |  | 
 | 	return 0; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_add_pingroup_range); | 
 |  | 
 | /** | 
 |  * gpiochip_add_pin_range() - add a range for GPIO <-> pin mapping | 
 |  * @chip: the gpiochip to add the range for | 
 |  * @pinctrl_name: the dev_name() of the pin controller to map to | 
 |  * @gpio_offset: the start offset in the current gpio_chip number space | 
 |  * @pin_offset: the start offset in the pin controller number space | 
 |  * @npins: the number of pins from the offset of each pin space (GPIO and | 
 |  *	pin controller) to accumulate in this range | 
 |  */ | 
 | int gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name, | 
 | 			   unsigned int gpio_offset, unsigned int pin_offset, | 
 | 			   unsigned int npins) | 
 | { | 
 | 	struct gpio_pin_range *pin_range; | 
 | 	struct gpio_device *gdev = chip->gpiodev; | 
 | 	int ret; | 
 |  | 
 | 	pin_range = kzalloc(sizeof(*pin_range), GFP_KERNEL); | 
 | 	if (!pin_range) { | 
 | 		chip_err(chip, "failed to allocate pin ranges\n"); | 
 | 		return -ENOMEM; | 
 | 	} | 
 |  | 
 | 	/* Use local offset as range ID */ | 
 | 	pin_range->range.id = gpio_offset; | 
 | 	pin_range->range.gc = chip; | 
 | 	pin_range->range.name = chip->label; | 
 | 	pin_range->range.base = gdev->base + gpio_offset; | 
 | 	pin_range->range.pin_base = pin_offset; | 
 | 	pin_range->range.npins = npins; | 
 | 	pin_range->pctldev = pinctrl_find_and_add_gpio_range(pinctl_name, | 
 | 			&pin_range->range); | 
 | 	if (IS_ERR(pin_range->pctldev)) { | 
 | 		ret = PTR_ERR(pin_range->pctldev); | 
 | 		chip_err(chip, "could not create pin range\n"); | 
 | 		kfree(pin_range); | 
 | 		return ret; | 
 | 	} | 
 | 	chip_dbg(chip, "created GPIO range %d->%d ==> %s PIN %d->%d\n", | 
 | 		 gpio_offset, gpio_offset + npins - 1, | 
 | 		 pinctl_name, | 
 | 		 pin_offset, pin_offset + npins - 1); | 
 |  | 
 | 	list_add_tail(&pin_range->node, &gdev->pin_ranges); | 
 |  | 
 | 	return 0; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_add_pin_range); | 
 |  | 
 | /** | 
 |  * gpiochip_remove_pin_ranges() - remove all the GPIO <-> pin mappings | 
 |  * @chip: the chip to remove all the mappings for | 
 |  */ | 
 | void gpiochip_remove_pin_ranges(struct gpio_chip *chip) | 
 | { | 
 | 	struct gpio_pin_range *pin_range, *tmp; | 
 | 	struct gpio_device *gdev = chip->gpiodev; | 
 |  | 
 | 	list_for_each_entry_safe(pin_range, tmp, &gdev->pin_ranges, node) { | 
 | 		list_del(&pin_range->node); | 
 | 		pinctrl_remove_gpio_range(pin_range->pctldev, | 
 | 				&pin_range->range); | 
 | 		kfree(pin_range); | 
 | 	} | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_remove_pin_ranges); | 
 |  | 
 | #endif /* CONFIG_PINCTRL */ | 
 |  | 
 | /* These "optional" allocation calls help prevent drivers from stomping | 
 |  * on each other, and help provide better diagnostics in debugfs. | 
 |  * They're called even less than the "set direction" calls. | 
 |  */ | 
 | static int __gpiod_request(struct gpio_desc *desc, const char *label) | 
 | { | 
 | 	struct gpio_chip	*chip = desc->gdev->chip; | 
 | 	int			status; | 
 | 	unsigned long		flags; | 
 |  | 
 | 	spin_lock_irqsave(&gpio_lock, flags); | 
 |  | 
 | 	/* NOTE:  gpio_request() can be called in early boot, | 
 | 	 * before IRQs are enabled, for non-sleeping (SOC) GPIOs. | 
 | 	 */ | 
 |  | 
 | 	if (test_and_set_bit(FLAG_REQUESTED, &desc->flags) == 0) { | 
 | 		desc_set_label(desc, label ? : "?"); | 
 | 		status = 0; | 
 | 	} else { | 
 | 		status = -EBUSY; | 
 | 		goto done; | 
 | 	} | 
 |  | 
 | 	if (chip->request) { | 
 | 		/* chip->request may sleep */ | 
 | 		spin_unlock_irqrestore(&gpio_lock, flags); | 
 | 		status = chip->request(chip, gpio_chip_hwgpio(desc)); | 
 | 		spin_lock_irqsave(&gpio_lock, flags); | 
 |  | 
 | 		if (status < 0) { | 
 | 			desc_set_label(desc, NULL); | 
 | 			clear_bit(FLAG_REQUESTED, &desc->flags); | 
 | 			goto done; | 
 | 		} | 
 | 	} | 
 | 	if (chip->get_direction) { | 
 | 		/* chip->get_direction may sleep */ | 
 | 		spin_unlock_irqrestore(&gpio_lock, flags); | 
 | 		gpiod_get_direction(desc); | 
 | 		spin_lock_irqsave(&gpio_lock, flags); | 
 | 	} | 
 | done: | 
 | 	spin_unlock_irqrestore(&gpio_lock, flags); | 
 | 	return status; | 
 | } | 
 |  | 
 | /* | 
 |  * This descriptor validation needs to be inserted verbatim into each | 
 |  * function taking a descriptor, so we need to use a preprocessor | 
 |  * macro to avoid endless duplication. If the desc is NULL it is an | 
 |  * optional GPIO and calls should just bail out. | 
 |  */ | 
 | #define VALIDATE_DESC(desc) do { \ | 
 | 	if (!desc) \ | 
 | 		return 0; \ | 
 | 	if (IS_ERR(desc)) {						\ | 
 | 		pr_warn("%s: invalid GPIO (errorpointer)\n", __func__); \ | 
 | 		return PTR_ERR(desc); \ | 
 | 	} \ | 
 | 	if (!desc->gdev) { \ | 
 | 		pr_warn("%s: invalid GPIO (no device)\n", __func__); \ | 
 | 		return -EINVAL; \ | 
 | 	} \ | 
 | 	if ( !desc->gdev->chip ) { \ | 
 | 		dev_warn(&desc->gdev->dev, \ | 
 | 			 "%s: backing chip is gone\n", __func__); \ | 
 | 		return 0; \ | 
 | 	} } while (0) | 
 |  | 
 | #define VALIDATE_DESC_VOID(desc) do { \ | 
 | 	if (!desc) \ | 
 | 		return; \ | 
 | 	if (IS_ERR(desc)) {						\ | 
 | 		pr_warn("%s: invalid GPIO (errorpointer)\n", __func__); \ | 
 | 		return; \ | 
 | 	} \ | 
 | 	if (!desc->gdev) { \ | 
 | 		pr_warn("%s: invalid GPIO (no device)\n", __func__); \ | 
 | 		return; \ | 
 | 	} \ | 
 | 	if (!desc->gdev->chip) { \ | 
 | 		dev_warn(&desc->gdev->dev, \ | 
 | 			 "%s: backing chip is gone\n", __func__); \ | 
 | 		return; \ | 
 | 	} } while (0) | 
 |  | 
 |  | 
 | int gpiod_request(struct gpio_desc *desc, const char *label) | 
 | { | 
 | 	int status = -EPROBE_DEFER; | 
 | 	struct gpio_device *gdev; | 
 |  | 
 | 	VALIDATE_DESC(desc); | 
 | 	gdev = desc->gdev; | 
 |  | 
 | 	if (try_module_get(gdev->owner)) { | 
 | 		status = __gpiod_request(desc, label); | 
 | 		if (status < 0) | 
 | 			module_put(gdev->owner); | 
 | 		else | 
 | 			get_device(&gdev->dev); | 
 | 	} | 
 |  | 
 | 	if (status) | 
 | 		gpiod_dbg(desc, "%s: status %d\n", __func__, status); | 
 |  | 
 | 	return status; | 
 | } | 
 |  | 
 | static bool __gpiod_free(struct gpio_desc *desc) | 
 | { | 
 | 	bool			ret = false; | 
 | 	unsigned long		flags; | 
 | 	struct gpio_chip	*chip; | 
 |  | 
 | 	might_sleep(); | 
 |  | 
 | 	gpiod_unexport(desc); | 
 |  | 
 | 	spin_lock_irqsave(&gpio_lock, flags); | 
 |  | 
 | 	chip = desc->gdev->chip; | 
 | 	if (chip && test_bit(FLAG_REQUESTED, &desc->flags)) { | 
 | 		if (chip->free) { | 
 | 			spin_unlock_irqrestore(&gpio_lock, flags); | 
 | 			might_sleep_if(chip->can_sleep); | 
 | 			chip->free(chip, gpio_chip_hwgpio(desc)); | 
 | 			spin_lock_irqsave(&gpio_lock, flags); | 
 | 		} | 
 | 		desc_set_label(desc, NULL); | 
 | 		clear_bit(FLAG_ACTIVE_LOW, &desc->flags); | 
 | 		clear_bit(FLAG_REQUESTED, &desc->flags); | 
 | 		clear_bit(FLAG_OPEN_DRAIN, &desc->flags); | 
 | 		clear_bit(FLAG_OPEN_SOURCE, &desc->flags); | 
 | 		clear_bit(FLAG_IS_HOGGED, &desc->flags); | 
 | 		ret = true; | 
 | 	} | 
 |  | 
 | 	spin_unlock_irqrestore(&gpio_lock, flags); | 
 | 	return ret; | 
 | } | 
 |  | 
 | void gpiod_free(struct gpio_desc *desc) | 
 | { | 
 | 	if (desc && desc->gdev && __gpiod_free(desc)) { | 
 | 		module_put(desc->gdev->owner); | 
 | 		put_device(&desc->gdev->dev); | 
 | 	} else { | 
 | 		WARN_ON(extra_checks); | 
 | 	} | 
 | } | 
 |  | 
 | /** | 
 |  * gpiochip_is_requested - return string iff signal was requested | 
 |  * @chip: controller managing the signal | 
 |  * @offset: of signal within controller's 0..(ngpio - 1) range | 
 |  * | 
 |  * Returns NULL if the GPIO is not currently requested, else a string. | 
 |  * The string returned is the label passed to gpio_request(); if none has been | 
 |  * passed it is a meaningless, non-NULL constant. | 
 |  * | 
 |  * This function is for use by GPIO controller drivers.  The label can | 
 |  * help with diagnostics, and knowing that the signal is used as a GPIO | 
 |  * can help avoid accidentally multiplexing it to another controller. | 
 |  */ | 
 | const char *gpiochip_is_requested(struct gpio_chip *chip, unsigned offset) | 
 | { | 
 | 	struct gpio_desc *desc; | 
 |  | 
 | 	if (offset >= chip->ngpio) | 
 | 		return NULL; | 
 |  | 
 | 	desc = &chip->gpiodev->descs[offset]; | 
 |  | 
 | 	if (test_bit(FLAG_REQUESTED, &desc->flags) == 0) | 
 | 		return NULL; | 
 | 	return desc->label; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_is_requested); | 
 |  | 
 | /** | 
 |  * gpiochip_request_own_desc - Allow GPIO chip to request its own descriptor | 
 |  * @desc: GPIO descriptor to request | 
 |  * @label: label for the GPIO | 
 |  * | 
 |  * Function allows GPIO chip drivers to request and use their own GPIO | 
 |  * descriptors via gpiolib API. Difference to gpiod_request() is that this | 
 |  * function will not increase reference count of the GPIO chip module. This | 
 |  * allows the GPIO chip module to be unloaded as needed (we assume that the | 
 |  * GPIO chip driver handles freeing the GPIOs it has requested). | 
 |  */ | 
 | struct gpio_desc *gpiochip_request_own_desc(struct gpio_chip *chip, u16 hwnum, | 
 | 					    const char *label) | 
 | { | 
 | 	struct gpio_desc *desc = gpiochip_get_desc(chip, hwnum); | 
 | 	int err; | 
 |  | 
 | 	if (IS_ERR(desc)) { | 
 | 		chip_err(chip, "failed to get GPIO descriptor\n"); | 
 | 		return desc; | 
 | 	} | 
 |  | 
 | 	err = __gpiod_request(desc, label); | 
 | 	if (err < 0) | 
 | 		return ERR_PTR(err); | 
 |  | 
 | 	return desc; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_request_own_desc); | 
 |  | 
 | /** | 
 |  * gpiochip_free_own_desc - Free GPIO requested by the chip driver | 
 |  * @desc: GPIO descriptor to free | 
 |  * | 
 |  * Function frees the given GPIO requested previously with | 
 |  * gpiochip_request_own_desc(). | 
 |  */ | 
 | void gpiochip_free_own_desc(struct gpio_desc *desc) | 
 | { | 
 | 	if (desc) | 
 | 		__gpiod_free(desc); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_free_own_desc); | 
 |  | 
 | /* | 
 |  * Drivers MUST set GPIO direction before making get/set calls.  In | 
 |  * some cases this is done in early boot, before IRQs are enabled. | 
 |  * | 
 |  * As a rule these aren't called more than once (except for drivers | 
 |  * using the open-drain emulation idiom) so these are natural places | 
 |  * to accumulate extra debugging checks.  Note that we can't (yet) | 
 |  * rely on gpio_request() having been called beforehand. | 
 |  */ | 
 |  | 
 | /** | 
 |  * gpiod_direction_input - set the GPIO direction to input | 
 |  * @desc:	GPIO to set to input | 
 |  * | 
 |  * Set the direction of the passed GPIO to input, such as gpiod_get_value() can | 
 |  * be called safely on it. | 
 |  * | 
 |  * Return 0 in case of success, else an error code. | 
 |  */ | 
 | int gpiod_direction_input(struct gpio_desc *desc) | 
 | { | 
 | 	struct gpio_chip	*chip; | 
 | 	int			status = -EINVAL; | 
 |  | 
 | 	VALIDATE_DESC(desc); | 
 | 	chip = desc->gdev->chip; | 
 |  | 
 | 	if (!chip->get || !chip->direction_input) { | 
 | 		gpiod_warn(desc, | 
 | 			"%s: missing get() or direction_input() operations\n", | 
 | 			__func__); | 
 | 		return -EIO; | 
 | 	} | 
 |  | 
 | 	status = chip->direction_input(chip, gpio_chip_hwgpio(desc)); | 
 | 	if (status == 0) | 
 | 		clear_bit(FLAG_IS_OUT, &desc->flags); | 
 |  | 
 | 	trace_gpio_direction(desc_to_gpio(desc), 1, status); | 
 |  | 
 | 	return status; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_direction_input); | 
 |  | 
 | static int gpio_set_drive_single_ended(struct gpio_chip *gc, unsigned offset, | 
 | 				       enum pin_config_param mode) | 
 | { | 
 | 	unsigned long config = { PIN_CONF_PACKED(mode, 0) }; | 
 |  | 
 | 	return gc->set_config ? gc->set_config(gc, offset, config) : -ENOTSUPP; | 
 | } | 
 |  | 
 | static int _gpiod_direction_output_raw(struct gpio_desc *desc, int value) | 
 | { | 
 | 	struct gpio_chip *gc = desc->gdev->chip; | 
 | 	int val = !!value; | 
 | 	int ret; | 
 |  | 
 | 	/* GPIOs used for IRQs shall not be set as output */ | 
 | 	if (test_bit(FLAG_USED_AS_IRQ, &desc->flags)) { | 
 | 		gpiod_err(desc, | 
 | 			  "%s: tried to set a GPIO tied to an IRQ as output\n", | 
 | 			  __func__); | 
 | 		return -EIO; | 
 | 	} | 
 |  | 
 | 	if (test_bit(FLAG_OPEN_DRAIN, &desc->flags)) { | 
 | 		/* First see if we can enable open drain in hardware */ | 
 | 		ret = gpio_set_drive_single_ended(gc, gpio_chip_hwgpio(desc), | 
 | 						  PIN_CONFIG_DRIVE_OPEN_DRAIN); | 
 | 		if (!ret) | 
 | 			goto set_output_value; | 
 | 		/* Emulate open drain by not actively driving the line high */ | 
 | 		if (val) | 
 | 			return gpiod_direction_input(desc); | 
 | 	} | 
 | 	else if (test_bit(FLAG_OPEN_SOURCE, &desc->flags)) { | 
 | 		ret = gpio_set_drive_single_ended(gc, gpio_chip_hwgpio(desc), | 
 | 						  PIN_CONFIG_DRIVE_OPEN_SOURCE); | 
 | 		if (!ret) | 
 | 			goto set_output_value; | 
 | 		/* Emulate open source by not actively driving the line low */ | 
 | 		if (!val) | 
 | 			return gpiod_direction_input(desc); | 
 | 	} else { | 
 | 		gpio_set_drive_single_ended(gc, gpio_chip_hwgpio(desc), | 
 | 					    PIN_CONFIG_DRIVE_PUSH_PULL); | 
 | 	} | 
 |  | 
 | set_output_value: | 
 | 	if (!gc->set || !gc->direction_output) { | 
 | 		gpiod_warn(desc, | 
 | 		       "%s: missing set() or direction_output() operations\n", | 
 | 		       __func__); | 
 | 		return -EIO; | 
 | 	} | 
 |  | 
 | 	ret = gc->direction_output(gc, gpio_chip_hwgpio(desc), val); | 
 | 	if (!ret) | 
 | 		set_bit(FLAG_IS_OUT, &desc->flags); | 
 | 	trace_gpio_value(desc_to_gpio(desc), 0, val); | 
 | 	trace_gpio_direction(desc_to_gpio(desc), 0, ret); | 
 | 	return ret; | 
 | } | 
 |  | 
 | /** | 
 |  * gpiod_direction_output_raw - set the GPIO direction to output | 
 |  * @desc:	GPIO to set to output | 
 |  * @value:	initial output value of the GPIO | 
 |  * | 
 |  * Set the direction of the passed GPIO to output, such as gpiod_set_value() can | 
 |  * be called safely on it. The initial value of the output must be specified | 
 |  * as raw value on the physical line without regard for the ACTIVE_LOW status. | 
 |  * | 
 |  * Return 0 in case of success, else an error code. | 
 |  */ | 
 | int gpiod_direction_output_raw(struct gpio_desc *desc, int value) | 
 | { | 
 | 	VALIDATE_DESC(desc); | 
 | 	return _gpiod_direction_output_raw(desc, value); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_direction_output_raw); | 
 |  | 
 | /** | 
 |  * gpiod_direction_output - set the GPIO direction to output | 
 |  * @desc:	GPIO to set to output | 
 |  * @value:	initial output value of the GPIO | 
 |  * | 
 |  * Set the direction of the passed GPIO to output, such as gpiod_set_value() can | 
 |  * be called safely on it. The initial value of the output must be specified | 
 |  * as the logical value of the GPIO, i.e. taking its ACTIVE_LOW status into | 
 |  * account. | 
 |  * | 
 |  * Return 0 in case of success, else an error code. | 
 |  */ | 
 | int gpiod_direction_output(struct gpio_desc *desc, int value) | 
 | { | 
 | 	VALIDATE_DESC(desc); | 
 | 	if (test_bit(FLAG_ACTIVE_LOW, &desc->flags)) | 
 | 		value = !value; | 
 | 	else | 
 | 		value = !!value; | 
 | 	return _gpiod_direction_output_raw(desc, value); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_direction_output); | 
 |  | 
 | /** | 
 |  * gpiod_set_debounce - sets @debounce time for a @gpio | 
 |  * @gpio: the gpio to set debounce time | 
 |  * @debounce: debounce time is microseconds | 
 |  * | 
 |  * returns -ENOTSUPP if the controller does not support setting | 
 |  * debounce. | 
 |  */ | 
 | int gpiod_set_debounce(struct gpio_desc *desc, unsigned debounce) | 
 | { | 
 | 	struct gpio_chip	*chip; | 
 | 	unsigned long		config; | 
 |  | 
 | 	VALIDATE_DESC(desc); | 
 | 	chip = desc->gdev->chip; | 
 | 	if (!chip->set || !chip->set_config) { | 
 | 		gpiod_dbg(desc, | 
 | 			  "%s: missing set() or set_config() operations\n", | 
 | 			  __func__); | 
 | 		return -ENOTSUPP; | 
 | 	} | 
 |  | 
 | 	config = pinconf_to_config_packed(PIN_CONFIG_INPUT_DEBOUNCE, debounce); | 
 | 	return chip->set_config(chip, gpio_chip_hwgpio(desc), config); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_set_debounce); | 
 |  | 
 | /** | 
 |  * gpiod_is_active_low - test whether a GPIO is active-low or not | 
 |  * @desc: the gpio descriptor to test | 
 |  * | 
 |  * Returns 1 if the GPIO is active-low, 0 otherwise. | 
 |  */ | 
 | int gpiod_is_active_low(const struct gpio_desc *desc) | 
 | { | 
 | 	VALIDATE_DESC(desc); | 
 | 	return test_bit(FLAG_ACTIVE_LOW, &desc->flags); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_is_active_low); | 
 |  | 
 | /* I/O calls are only valid after configuration completed; the relevant | 
 |  * "is this a valid GPIO" error checks should already have been done. | 
 |  * | 
 |  * "Get" operations are often inlinable as reading a pin value register, | 
 |  * and masking the relevant bit in that register. | 
 |  * | 
 |  * When "set" operations are inlinable, they involve writing that mask to | 
 |  * one register to set a low value, or a different register to set it high. | 
 |  * Otherwise locking is needed, so there may be little value to inlining. | 
 |  * | 
 |  *------------------------------------------------------------------------ | 
 |  * | 
 |  * IMPORTANT!!!  The hot paths -- get/set value -- assume that callers | 
 |  * have requested the GPIO.  That can include implicit requesting by | 
 |  * a direction setting call.  Marking a gpio as requested locks its chip | 
 |  * in memory, guaranteeing that these table lookups need no more locking | 
 |  * and that gpiochip_remove() will fail. | 
 |  * | 
 |  * REVISIT when debugging, consider adding some instrumentation to ensure | 
 |  * that the GPIO was actually requested. | 
 |  */ | 
 |  | 
 | static int _gpiod_get_raw_value(const struct gpio_desc *desc) | 
 | { | 
 | 	struct gpio_chip	*chip; | 
 | 	int offset; | 
 | 	int value; | 
 |  | 
 | 	chip = desc->gdev->chip; | 
 | 	offset = gpio_chip_hwgpio(desc); | 
 | 	value = chip->get ? chip->get(chip, offset) : -EIO; | 
 | 	value = value < 0 ? value : !!value; | 
 | 	trace_gpio_value(desc_to_gpio(desc), 1, value); | 
 | 	return value; | 
 | } | 
 |  | 
 | /** | 
 |  * gpiod_get_raw_value() - return a gpio's raw value | 
 |  * @desc: gpio whose value will be returned | 
 |  * | 
 |  * Return the GPIO's raw value, i.e. the value of the physical line disregarding | 
 |  * its ACTIVE_LOW status, or negative errno on failure. | 
 |  * | 
 |  * This function should be called from contexts where we cannot sleep, and will | 
 |  * complain if the GPIO chip functions potentially sleep. | 
 |  */ | 
 | int gpiod_get_raw_value(const struct gpio_desc *desc) | 
 | { | 
 | 	VALIDATE_DESC(desc); | 
 | 	/* Should be using gpio_get_value_cansleep() */ | 
 | 	WARN_ON(desc->gdev->chip->can_sleep); | 
 | 	return _gpiod_get_raw_value(desc); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_get_raw_value); | 
 |  | 
 | /** | 
 |  * gpiod_get_value() - return a gpio's value | 
 |  * @desc: gpio whose value will be returned | 
 |  * | 
 |  * Return the GPIO's logical value, i.e. taking the ACTIVE_LOW status into | 
 |  * account, or negative errno on failure. | 
 |  * | 
 |  * This function should be called from contexts where we cannot sleep, and will | 
 |  * complain if the GPIO chip functions potentially sleep. | 
 |  */ | 
 | int gpiod_get_value(const struct gpio_desc *desc) | 
 | { | 
 | 	int value; | 
 |  | 
 | 	VALIDATE_DESC(desc); | 
 | 	/* Should be using gpio_get_value_cansleep() */ | 
 | 	WARN_ON(desc->gdev->chip->can_sleep); | 
 |  | 
 | 	value = _gpiod_get_raw_value(desc); | 
 | 	if (value < 0) | 
 | 		return value; | 
 |  | 
 | 	if (test_bit(FLAG_ACTIVE_LOW, &desc->flags)) | 
 | 		value = !value; | 
 |  | 
 | 	return value; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_get_value); | 
 |  | 
 | /* | 
 |  *  _gpio_set_open_drain_value() - Set the open drain gpio's value. | 
 |  * @desc: gpio descriptor whose state need to be set. | 
 |  * @value: Non-zero for setting it HIGH otherwise it will set to LOW. | 
 |  */ | 
 | static void _gpio_set_open_drain_value(struct gpio_desc *desc, bool value) | 
 | { | 
 | 	int err = 0; | 
 | 	struct gpio_chip *chip = desc->gdev->chip; | 
 | 	int offset = gpio_chip_hwgpio(desc); | 
 |  | 
 | 	if (value) { | 
 | 		err = chip->direction_input(chip, offset); | 
 | 		if (!err) | 
 | 			clear_bit(FLAG_IS_OUT, &desc->flags); | 
 | 	} else { | 
 | 		err = chip->direction_output(chip, offset, 0); | 
 | 		if (!err) | 
 | 			set_bit(FLAG_IS_OUT, &desc->flags); | 
 | 	} | 
 | 	trace_gpio_direction(desc_to_gpio(desc), value, err); | 
 | 	if (err < 0) | 
 | 		gpiod_err(desc, | 
 | 			  "%s: Error in set_value for open drain err %d\n", | 
 | 			  __func__, err); | 
 | } | 
 |  | 
 | /* | 
 |  *  _gpio_set_open_source_value() - Set the open source gpio's value. | 
 |  * @desc: gpio descriptor whose state need to be set. | 
 |  * @value: Non-zero for setting it HIGH otherwise it will set to LOW. | 
 |  */ | 
 | static void _gpio_set_open_source_value(struct gpio_desc *desc, bool value) | 
 | { | 
 | 	int err = 0; | 
 | 	struct gpio_chip *chip = desc->gdev->chip; | 
 | 	int offset = gpio_chip_hwgpio(desc); | 
 |  | 
 | 	if (value) { | 
 | 		err = chip->direction_output(chip, offset, 1); | 
 | 		if (!err) | 
 | 			set_bit(FLAG_IS_OUT, &desc->flags); | 
 | 	} else { | 
 | 		err = chip->direction_input(chip, offset); | 
 | 		if (!err) | 
 | 			clear_bit(FLAG_IS_OUT, &desc->flags); | 
 | 	} | 
 | 	trace_gpio_direction(desc_to_gpio(desc), !value, err); | 
 | 	if (err < 0) | 
 | 		gpiod_err(desc, | 
 | 			  "%s: Error in set_value for open source err %d\n", | 
 | 			  __func__, err); | 
 | } | 
 |  | 
 | static void _gpiod_set_raw_value(struct gpio_desc *desc, bool value) | 
 | { | 
 | 	struct gpio_chip	*chip; | 
 |  | 
 | 	chip = desc->gdev->chip; | 
 | 	trace_gpio_value(desc_to_gpio(desc), 0, value); | 
 | 	if (test_bit(FLAG_OPEN_DRAIN, &desc->flags)) | 
 | 		_gpio_set_open_drain_value(desc, value); | 
 | 	else if (test_bit(FLAG_OPEN_SOURCE, &desc->flags)) | 
 | 		_gpio_set_open_source_value(desc, value); | 
 | 	else | 
 | 		chip->set(chip, gpio_chip_hwgpio(desc), value); | 
 | } | 
 |  | 
 | /* | 
 |  * set multiple outputs on the same chip; | 
 |  * use the chip's set_multiple function if available; | 
 |  * otherwise set the outputs sequentially; | 
 |  * @mask: bit mask array; one bit per output; BITS_PER_LONG bits per word | 
 |  *        defines which outputs are to be changed | 
 |  * @bits: bit value array; one bit per output; BITS_PER_LONG bits per word | 
 |  *        defines the values the outputs specified by mask are to be set to | 
 |  */ | 
 | static void gpio_chip_set_multiple(struct gpio_chip *chip, | 
 | 				   unsigned long *mask, unsigned long *bits) | 
 | { | 
 | 	if (chip->set_multiple) { | 
 | 		chip->set_multiple(chip, mask, bits); | 
 | 	} else { | 
 | 		unsigned int i; | 
 |  | 
 | 		/* set outputs if the corresponding mask bit is set */ | 
 | 		for_each_set_bit(i, mask, chip->ngpio) | 
 | 			chip->set(chip, i, test_bit(i, bits)); | 
 | 	} | 
 | } | 
 |  | 
 | void gpiod_set_array_value_complex(bool raw, bool can_sleep, | 
 | 				   unsigned int array_size, | 
 | 				   struct gpio_desc **desc_array, | 
 | 				   int *value_array) | 
 | { | 
 | 	int i = 0; | 
 |  | 
 | 	while (i < array_size) { | 
 | 		struct gpio_chip *chip = desc_array[i]->gdev->chip; | 
 | 		unsigned long mask[BITS_TO_LONGS(chip->ngpio)]; | 
 | 		unsigned long bits[BITS_TO_LONGS(chip->ngpio)]; | 
 | 		int count = 0; | 
 |  | 
 | 		if (!can_sleep) | 
 | 			WARN_ON(chip->can_sleep); | 
 |  | 
 | 		memset(mask, 0, sizeof(mask)); | 
 | 		do { | 
 | 			struct gpio_desc *desc = desc_array[i]; | 
 | 			int hwgpio = gpio_chip_hwgpio(desc); | 
 | 			int value = value_array[i]; | 
 |  | 
 | 			if (!raw && test_bit(FLAG_ACTIVE_LOW, &desc->flags)) | 
 | 				value = !value; | 
 | 			trace_gpio_value(desc_to_gpio(desc), 0, value); | 
 | 			/* | 
 | 			 * collect all normal outputs belonging to the same chip | 
 | 			 * open drain and open source outputs are set individually | 
 | 			 */ | 
 | 			if (test_bit(FLAG_OPEN_DRAIN, &desc->flags)) { | 
 | 				_gpio_set_open_drain_value(desc, value); | 
 | 			} else if (test_bit(FLAG_OPEN_SOURCE, &desc->flags)) { | 
 | 				_gpio_set_open_source_value(desc, value); | 
 | 			} else { | 
 | 				__set_bit(hwgpio, mask); | 
 | 				if (value) | 
 | 					__set_bit(hwgpio, bits); | 
 | 				else | 
 | 					__clear_bit(hwgpio, bits); | 
 | 				count++; | 
 | 			} | 
 | 			i++; | 
 | 		} while ((i < array_size) && | 
 | 			 (desc_array[i]->gdev->chip == chip)); | 
 | 		/* push collected bits to outputs */ | 
 | 		if (count != 0) | 
 | 			gpio_chip_set_multiple(chip, mask, bits); | 
 | 	} | 
 | } | 
 |  | 
 | /** | 
 |  * gpiod_set_raw_value() - assign a gpio's raw value | 
 |  * @desc: gpio whose value will be assigned | 
 |  * @value: value to assign | 
 |  * | 
 |  * Set the raw value of the GPIO, i.e. the value of its physical line without | 
 |  * regard for its ACTIVE_LOW status. | 
 |  * | 
 |  * This function should be called from contexts where we cannot sleep, and will | 
 |  * complain if the GPIO chip functions potentially sleep. | 
 |  */ | 
 | void gpiod_set_raw_value(struct gpio_desc *desc, int value) | 
 | { | 
 | 	VALIDATE_DESC_VOID(desc); | 
 | 	/* Should be using gpiod_set_value_cansleep() */ | 
 | 	WARN_ON(desc->gdev->chip->can_sleep); | 
 | 	_gpiod_set_raw_value(desc, value); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_set_raw_value); | 
 |  | 
 | /** | 
 |  * gpiod_set_value() - assign a gpio's value | 
 |  * @desc: gpio whose value will be assigned | 
 |  * @value: value to assign | 
 |  * | 
 |  * Set the logical value of the GPIO, i.e. taking its ACTIVE_LOW status into | 
 |  * account | 
 |  * | 
 |  * This function should be called from contexts where we cannot sleep, and will | 
 |  * complain if the GPIO chip functions potentially sleep. | 
 |  */ | 
 | void gpiod_set_value(struct gpio_desc *desc, int value) | 
 | { | 
 | 	VALIDATE_DESC_VOID(desc); | 
 | 	/* Should be using gpiod_set_value_cansleep() */ | 
 | 	WARN_ON(desc->gdev->chip->can_sleep); | 
 | 	if (test_bit(FLAG_ACTIVE_LOW, &desc->flags)) | 
 | 		value = !value; | 
 | 	_gpiod_set_raw_value(desc, value); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_set_value); | 
 |  | 
 | /** | 
 |  * gpiod_set_raw_array_value() - assign values to an array of GPIOs | 
 |  * @array_size: number of elements in the descriptor / value arrays | 
 |  * @desc_array: array of GPIO descriptors whose values will be assigned | 
 |  * @value_array: array of values to assign | 
 |  * | 
 |  * Set the raw values of the GPIOs, i.e. the values of the physical lines | 
 |  * without regard for their ACTIVE_LOW status. | 
 |  * | 
 |  * This function should be called from contexts where we cannot sleep, and will | 
 |  * complain if the GPIO chip functions potentially sleep. | 
 |  */ | 
 | void gpiod_set_raw_array_value(unsigned int array_size, | 
 | 			 struct gpio_desc **desc_array, int *value_array) | 
 | { | 
 | 	if (!desc_array) | 
 | 		return; | 
 | 	gpiod_set_array_value_complex(true, false, array_size, desc_array, | 
 | 				      value_array); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_set_raw_array_value); | 
 |  | 
 | /** | 
 |  * gpiod_set_array_value() - assign values to an array of GPIOs | 
 |  * @array_size: number of elements in the descriptor / value arrays | 
 |  * @desc_array: array of GPIO descriptors whose values will be assigned | 
 |  * @value_array: array of values to assign | 
 |  * | 
 |  * Set the logical values of the GPIOs, i.e. taking their ACTIVE_LOW status | 
 |  * into account. | 
 |  * | 
 |  * This function should be called from contexts where we cannot sleep, and will | 
 |  * complain if the GPIO chip functions potentially sleep. | 
 |  */ | 
 | void gpiod_set_array_value(unsigned int array_size, | 
 | 			   struct gpio_desc **desc_array, int *value_array) | 
 | { | 
 | 	if (!desc_array) | 
 | 		return; | 
 | 	gpiod_set_array_value_complex(false, false, array_size, desc_array, | 
 | 				      value_array); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_set_array_value); | 
 |  | 
 | /** | 
 |  * gpiod_cansleep() - report whether gpio value access may sleep | 
 |  * @desc: gpio to check | 
 |  * | 
 |  */ | 
 | int gpiod_cansleep(const struct gpio_desc *desc) | 
 | { | 
 | 	VALIDATE_DESC(desc); | 
 | 	return desc->gdev->chip->can_sleep; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_cansleep); | 
 |  | 
 | /** | 
 |  * gpiod_to_irq() - return the IRQ corresponding to a GPIO | 
 |  * @desc: gpio whose IRQ will be returned (already requested) | 
 |  * | 
 |  * Return the IRQ corresponding to the passed GPIO, or an error code in case of | 
 |  * error. | 
 |  */ | 
 | int gpiod_to_irq(const struct gpio_desc *desc) | 
 | { | 
 | 	struct gpio_chip *chip; | 
 | 	int offset; | 
 |  | 
 | 	/* | 
 | 	 * Cannot VALIDATE_DESC() here as gpiod_to_irq() consumer semantics | 
 | 	 * requires this function to not return zero on an invalid descriptor | 
 | 	 * but rather a negative error number. | 
 | 	 */ | 
 | 	if (!desc || IS_ERR(desc) || !desc->gdev || !desc->gdev->chip) | 
 | 		return -EINVAL; | 
 |  | 
 | 	chip = desc->gdev->chip; | 
 | 	offset = gpio_chip_hwgpio(desc); | 
 | 	if (chip->to_irq) { | 
 | 		int retirq = chip->to_irq(chip, offset); | 
 |  | 
 | 		/* Zero means NO_IRQ */ | 
 | 		if (!retirq) | 
 | 			return -ENXIO; | 
 |  | 
 | 		return retirq; | 
 | 	} | 
 | 	return -ENXIO; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_to_irq); | 
 |  | 
 | /** | 
 |  * gpiochip_lock_as_irq() - lock a GPIO to be used as IRQ | 
 |  * @chip: the chip the GPIO to lock belongs to | 
 |  * @offset: the offset of the GPIO to lock as IRQ | 
 |  * | 
 |  * This is used directly by GPIO drivers that want to lock down | 
 |  * a certain GPIO line to be used for IRQs. | 
 |  */ | 
 | int gpiochip_lock_as_irq(struct gpio_chip *chip, unsigned int offset) | 
 | { | 
 | 	struct gpio_desc *desc; | 
 |  | 
 | 	desc = gpiochip_get_desc(chip, offset); | 
 | 	if (IS_ERR(desc)) | 
 | 		return PTR_ERR(desc); | 
 |  | 
 | 	/* | 
 | 	 * If it's fast: flush the direction setting if something changed | 
 | 	 * behind our back | 
 | 	 */ | 
 | 	if (!chip->can_sleep && chip->get_direction) { | 
 | 		int dir = chip->get_direction(chip, offset); | 
 |  | 
 | 		if (dir) | 
 | 			clear_bit(FLAG_IS_OUT, &desc->flags); | 
 | 		else | 
 | 			set_bit(FLAG_IS_OUT, &desc->flags); | 
 | 	} | 
 |  | 
 | 	if (test_bit(FLAG_IS_OUT, &desc->flags)) { | 
 | 		chip_err(chip, | 
 | 			  "%s: tried to flag a GPIO set as output for IRQ\n", | 
 | 			  __func__); | 
 | 		return -EIO; | 
 | 	} | 
 |  | 
 | 	set_bit(FLAG_USED_AS_IRQ, &desc->flags); | 
 |  | 
 | 	/* | 
 | 	 * If the consumer has not set up a label (such as when the | 
 | 	 * IRQ is referenced from .to_irq()) we set up a label here | 
 | 	 * so it is clear this is used as an interrupt. | 
 | 	 */ | 
 | 	if (!desc->label) | 
 | 		desc_set_label(desc, "interrupt"); | 
 |  | 
 | 	return 0; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_lock_as_irq); | 
 |  | 
 | /** | 
 |  * gpiochip_unlock_as_irq() - unlock a GPIO used as IRQ | 
 |  * @chip: the chip the GPIO to lock belongs to | 
 |  * @offset: the offset of the GPIO to lock as IRQ | 
 |  * | 
 |  * This is used directly by GPIO drivers that want to indicate | 
 |  * that a certain GPIO is no longer used exclusively for IRQ. | 
 |  */ | 
 | void gpiochip_unlock_as_irq(struct gpio_chip *chip, unsigned int offset) | 
 | { | 
 | 	struct gpio_desc *desc; | 
 |  | 
 | 	desc = gpiochip_get_desc(chip, offset); | 
 | 	if (IS_ERR(desc)) | 
 | 		return; | 
 |  | 
 | 	clear_bit(FLAG_USED_AS_IRQ, &desc->flags); | 
 |  | 
 | 	/* If we only had this marking, erase it */ | 
 | 	if (desc->label && !strcmp(desc->label, "interrupt")) | 
 | 		desc_set_label(desc, NULL); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_unlock_as_irq); | 
 |  | 
 | bool gpiochip_line_is_irq(struct gpio_chip *chip, unsigned int offset) | 
 | { | 
 | 	if (offset >= chip->ngpio) | 
 | 		return false; | 
 |  | 
 | 	return test_bit(FLAG_USED_AS_IRQ, &chip->gpiodev->descs[offset].flags); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_line_is_irq); | 
 |  | 
 | bool gpiochip_line_is_open_drain(struct gpio_chip *chip, unsigned int offset) | 
 | { | 
 | 	if (offset >= chip->ngpio) | 
 | 		return false; | 
 |  | 
 | 	return test_bit(FLAG_OPEN_DRAIN, &chip->gpiodev->descs[offset].flags); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_line_is_open_drain); | 
 |  | 
 | bool gpiochip_line_is_open_source(struct gpio_chip *chip, unsigned int offset) | 
 | { | 
 | 	if (offset >= chip->ngpio) | 
 | 		return false; | 
 |  | 
 | 	return test_bit(FLAG_OPEN_SOURCE, &chip->gpiodev->descs[offset].flags); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiochip_line_is_open_source); | 
 |  | 
 | /** | 
 |  * gpiod_get_raw_value_cansleep() - return a gpio's raw value | 
 |  * @desc: gpio whose value will be returned | 
 |  * | 
 |  * Return the GPIO's raw value, i.e. the value of the physical line disregarding | 
 |  * its ACTIVE_LOW status, or negative errno on failure. | 
 |  * | 
 |  * This function is to be called from contexts that can sleep. | 
 |  */ | 
 | int gpiod_get_raw_value_cansleep(const struct gpio_desc *desc) | 
 | { | 
 | 	might_sleep_if(extra_checks); | 
 | 	VALIDATE_DESC(desc); | 
 | 	return _gpiod_get_raw_value(desc); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_get_raw_value_cansleep); | 
 |  | 
 | /** | 
 |  * gpiod_get_value_cansleep() - return a gpio's value | 
 |  * @desc: gpio whose value will be returned | 
 |  * | 
 |  * Return the GPIO's logical value, i.e. taking the ACTIVE_LOW status into | 
 |  * account, or negative errno on failure. | 
 |  * | 
 |  * This function is to be called from contexts that can sleep. | 
 |  */ | 
 | int gpiod_get_value_cansleep(const struct gpio_desc *desc) | 
 | { | 
 | 	int value; | 
 |  | 
 | 	might_sleep_if(extra_checks); | 
 | 	VALIDATE_DESC(desc); | 
 | 	value = _gpiod_get_raw_value(desc); | 
 | 	if (value < 0) | 
 | 		return value; | 
 |  | 
 | 	if (test_bit(FLAG_ACTIVE_LOW, &desc->flags)) | 
 | 		value = !value; | 
 |  | 
 | 	return value; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_get_value_cansleep); | 
 |  | 
 | /** | 
 |  * gpiod_set_raw_value_cansleep() - assign a gpio's raw value | 
 |  * @desc: gpio whose value will be assigned | 
 |  * @value: value to assign | 
 |  * | 
 |  * Set the raw value of the GPIO, i.e. the value of its physical line without | 
 |  * regard for its ACTIVE_LOW status. | 
 |  * | 
 |  * This function is to be called from contexts that can sleep. | 
 |  */ | 
 | void gpiod_set_raw_value_cansleep(struct gpio_desc *desc, int value) | 
 | { | 
 | 	might_sleep_if(extra_checks); | 
 | 	VALIDATE_DESC_VOID(desc); | 
 | 	_gpiod_set_raw_value(desc, value); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_set_raw_value_cansleep); | 
 |  | 
 | /** | 
 |  * gpiod_set_value_cansleep() - assign a gpio's value | 
 |  * @desc: gpio whose value will be assigned | 
 |  * @value: value to assign | 
 |  * | 
 |  * Set the logical value of the GPIO, i.e. taking its ACTIVE_LOW status into | 
 |  * account | 
 |  * | 
 |  * This function is to be called from contexts that can sleep. | 
 |  */ | 
 | void gpiod_set_value_cansleep(struct gpio_desc *desc, int value) | 
 | { | 
 | 	might_sleep_if(extra_checks); | 
 | 	VALIDATE_DESC_VOID(desc); | 
 | 	if (test_bit(FLAG_ACTIVE_LOW, &desc->flags)) | 
 | 		value = !value; | 
 | 	_gpiod_set_raw_value(desc, value); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_set_value_cansleep); | 
 |  | 
 | /** | 
 |  * gpiod_set_raw_array_value_cansleep() - assign values to an array of GPIOs | 
 |  * @array_size: number of elements in the descriptor / value arrays | 
 |  * @desc_array: array of GPIO descriptors whose values will be assigned | 
 |  * @value_array: array of values to assign | 
 |  * | 
 |  * Set the raw values of the GPIOs, i.e. the values of the physical lines | 
 |  * without regard for their ACTIVE_LOW status. | 
 |  * | 
 |  * This function is to be called from contexts that can sleep. | 
 |  */ | 
 | void gpiod_set_raw_array_value_cansleep(unsigned int array_size, | 
 | 					struct gpio_desc **desc_array, | 
 | 					int *value_array) | 
 | { | 
 | 	might_sleep_if(extra_checks); | 
 | 	if (!desc_array) | 
 | 		return; | 
 | 	gpiod_set_array_value_complex(true, true, array_size, desc_array, | 
 | 				      value_array); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_set_raw_array_value_cansleep); | 
 |  | 
 | /** | 
 |  * gpiod_set_array_value_cansleep() - assign values to an array of GPIOs | 
 |  * @array_size: number of elements in the descriptor / value arrays | 
 |  * @desc_array: array of GPIO descriptors whose values will be assigned | 
 |  * @value_array: array of values to assign | 
 |  * | 
 |  * Set the logical values of the GPIOs, i.e. taking their ACTIVE_LOW status | 
 |  * into account. | 
 |  * | 
 |  * This function is to be called from contexts that can sleep. | 
 |  */ | 
 | void gpiod_set_array_value_cansleep(unsigned int array_size, | 
 | 				    struct gpio_desc **desc_array, | 
 | 				    int *value_array) | 
 | { | 
 | 	might_sleep_if(extra_checks); | 
 | 	if (!desc_array) | 
 | 		return; | 
 | 	gpiod_set_array_value_complex(false, true, array_size, desc_array, | 
 | 				      value_array); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_set_array_value_cansleep); | 
 |  | 
 | /** | 
 |  * gpiod_add_lookup_table() - register GPIO device consumers | 
 |  * @table: table of consumers to register | 
 |  */ | 
 | void gpiod_add_lookup_table(struct gpiod_lookup_table *table) | 
 | { | 
 | 	mutex_lock(&gpio_lookup_lock); | 
 |  | 
 | 	list_add_tail(&table->list, &gpio_lookup_list); | 
 |  | 
 | 	mutex_unlock(&gpio_lookup_lock); | 
 | } | 
 |  | 
 | /** | 
 |  * gpiod_remove_lookup_table() - unregister GPIO device consumers | 
 |  * @table: table of consumers to unregister | 
 |  */ | 
 | void gpiod_remove_lookup_table(struct gpiod_lookup_table *table) | 
 | { | 
 | 	mutex_lock(&gpio_lookup_lock); | 
 |  | 
 | 	list_del(&table->list); | 
 |  | 
 | 	mutex_unlock(&gpio_lookup_lock); | 
 | } | 
 |  | 
 | static struct gpiod_lookup_table *gpiod_find_lookup_table(struct device *dev) | 
 | { | 
 | 	const char *dev_id = dev ? dev_name(dev) : NULL; | 
 | 	struct gpiod_lookup_table *table; | 
 |  | 
 | 	mutex_lock(&gpio_lookup_lock); | 
 |  | 
 | 	list_for_each_entry(table, &gpio_lookup_list, list) { | 
 | 		if (table->dev_id && dev_id) { | 
 | 			/* | 
 | 			 * Valid strings on both ends, must be identical to have | 
 | 			 * a match | 
 | 			 */ | 
 | 			if (!strcmp(table->dev_id, dev_id)) | 
 | 				goto found; | 
 | 		} else { | 
 | 			/* | 
 | 			 * One of the pointers is NULL, so both must be to have | 
 | 			 * a match | 
 | 			 */ | 
 | 			if (dev_id == table->dev_id) | 
 | 				goto found; | 
 | 		} | 
 | 	} | 
 | 	table = NULL; | 
 |  | 
 | found: | 
 | 	mutex_unlock(&gpio_lookup_lock); | 
 | 	return table; | 
 | } | 
 |  | 
 | static struct gpio_desc *gpiod_find(struct device *dev, const char *con_id, | 
 | 				    unsigned int idx, | 
 | 				    enum gpio_lookup_flags *flags) | 
 | { | 
 | 	struct gpio_desc *desc = ERR_PTR(-ENOENT); | 
 | 	struct gpiod_lookup_table *table; | 
 | 	struct gpiod_lookup *p; | 
 |  | 
 | 	table = gpiod_find_lookup_table(dev); | 
 | 	if (!table) | 
 | 		return desc; | 
 |  | 
 | 	for (p = &table->table[0]; p->chip_label; p++) { | 
 | 		struct gpio_chip *chip; | 
 |  | 
 | 		/* idx must always match exactly */ | 
 | 		if (p->idx != idx) | 
 | 			continue; | 
 |  | 
 | 		/* If the lookup entry has a con_id, require exact match */ | 
 | 		if (p->con_id && (!con_id || strcmp(p->con_id, con_id))) | 
 | 			continue; | 
 |  | 
 | 		chip = find_chip_by_name(p->chip_label); | 
 |  | 
 | 		if (!chip) { | 
 | 			dev_err(dev, "cannot find GPIO chip %s\n", | 
 | 				p->chip_label); | 
 | 			return ERR_PTR(-ENODEV); | 
 | 		} | 
 |  | 
 | 		if (chip->ngpio <= p->chip_hwnum) { | 
 | 			dev_err(dev, | 
 | 				"requested GPIO %d is out of range [0..%d] for chip %s\n", | 
 | 				idx, chip->ngpio, chip->label); | 
 | 			return ERR_PTR(-EINVAL); | 
 | 		} | 
 |  | 
 | 		desc = gpiochip_get_desc(chip, p->chip_hwnum); | 
 | 		*flags = p->flags; | 
 |  | 
 | 		return desc; | 
 | 	} | 
 |  | 
 | 	return desc; | 
 | } | 
 |  | 
 | static int dt_gpio_count(struct device *dev, const char *con_id) | 
 | { | 
 | 	int ret; | 
 | 	char propname[32]; | 
 | 	unsigned int i; | 
 |  | 
 | 	for (i = 0; i < ARRAY_SIZE(gpio_suffixes); i++) { | 
 | 		if (con_id) | 
 | 			snprintf(propname, sizeof(propname), "%s-%s", | 
 | 				 con_id, gpio_suffixes[i]); | 
 | 		else | 
 | 			snprintf(propname, sizeof(propname), "%s", | 
 | 				 gpio_suffixes[i]); | 
 |  | 
 | 		ret = of_gpio_named_count(dev->of_node, propname); | 
 | 		if (ret >= 0) | 
 | 			break; | 
 | 	} | 
 | 	return ret; | 
 | } | 
 |  | 
 | static int platform_gpio_count(struct device *dev, const char *con_id) | 
 | { | 
 | 	struct gpiod_lookup_table *table; | 
 | 	struct gpiod_lookup *p; | 
 | 	unsigned int count = 0; | 
 |  | 
 | 	table = gpiod_find_lookup_table(dev); | 
 | 	if (!table) | 
 | 		return -ENOENT; | 
 |  | 
 | 	for (p = &table->table[0]; p->chip_label; p++) { | 
 | 		if ((con_id && p->con_id && !strcmp(con_id, p->con_id)) || | 
 | 		    (!con_id && !p->con_id)) | 
 | 			count++; | 
 | 	} | 
 | 	if (!count) | 
 | 		return -ENOENT; | 
 |  | 
 | 	return count; | 
 | } | 
 |  | 
 | /** | 
 |  * gpiod_count - return the number of GPIOs associated with a device / function | 
 |  *		or -ENOENT if no GPIO has been assigned to the requested function | 
 |  * @dev:	GPIO consumer, can be NULL for system-global GPIOs | 
 |  * @con_id:	function within the GPIO consumer | 
 |  */ | 
 | int gpiod_count(struct device *dev, const char *con_id) | 
 | { | 
 | 	int count = -ENOENT; | 
 |  | 
 | 	if (IS_ENABLED(CONFIG_OF) && dev && dev->of_node) | 
 | 		count = dt_gpio_count(dev, con_id); | 
 | 	else if (IS_ENABLED(CONFIG_ACPI) && dev && ACPI_HANDLE(dev)) | 
 | 		count = acpi_gpio_count(dev, con_id); | 
 |  | 
 | 	if (count < 0) | 
 | 		count = platform_gpio_count(dev, con_id); | 
 |  | 
 | 	return count; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_count); | 
 |  | 
 | /** | 
 |  * gpiod_get - obtain a GPIO for a given GPIO function | 
 |  * @dev:	GPIO consumer, can be NULL for system-global GPIOs | 
 |  * @con_id:	function within the GPIO consumer | 
 |  * @flags:	optional GPIO initialization flags | 
 |  * | 
 |  * Return the GPIO descriptor corresponding to the function con_id of device | 
 |  * dev, -ENOENT if no GPIO has been assigned to the requested function, or | 
 |  * another IS_ERR() code if an error occurred while trying to acquire the GPIO. | 
 |  */ | 
 | struct gpio_desc *__must_check gpiod_get(struct device *dev, const char *con_id, | 
 | 					 enum gpiod_flags flags) | 
 | { | 
 | 	return gpiod_get_index(dev, con_id, 0, flags); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_get); | 
 |  | 
 | /** | 
 |  * gpiod_get_optional - obtain an optional GPIO for a given GPIO function | 
 |  * @dev: GPIO consumer, can be NULL for system-global GPIOs | 
 |  * @con_id: function within the GPIO consumer | 
 |  * @flags: optional GPIO initialization flags | 
 |  * | 
 |  * This is equivalent to gpiod_get(), except that when no GPIO was assigned to | 
 |  * the requested function it will return NULL. This is convenient for drivers | 
 |  * that need to handle optional GPIOs. | 
 |  */ | 
 | struct gpio_desc *__must_check gpiod_get_optional(struct device *dev, | 
 | 						  const char *con_id, | 
 | 						  enum gpiod_flags flags) | 
 | { | 
 | 	return gpiod_get_index_optional(dev, con_id, 0, flags); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_get_optional); | 
 |  | 
 |  | 
 | /** | 
 |  * gpiod_configure_flags - helper function to configure a given GPIO | 
 |  * @desc:	gpio whose value will be assigned | 
 |  * @con_id:	function within the GPIO consumer | 
 |  * @lflags:	gpio_lookup_flags - returned from of_find_gpio() or | 
 |  *		of_get_gpio_hog() | 
 |  * @dflags:	gpiod_flags - optional GPIO initialization flags | 
 |  * | 
 |  * Return 0 on success, -ENOENT if no GPIO has been assigned to the | 
 |  * requested function and/or index, or another IS_ERR() code if an error | 
 |  * occurred while trying to acquire the GPIO. | 
 |  */ | 
 | static int gpiod_configure_flags(struct gpio_desc *desc, const char *con_id, | 
 | 		unsigned long lflags, enum gpiod_flags dflags) | 
 | { | 
 | 	int status; | 
 |  | 
 | 	if (lflags & GPIO_ACTIVE_LOW) | 
 | 		set_bit(FLAG_ACTIVE_LOW, &desc->flags); | 
 | 	if (lflags & GPIO_OPEN_DRAIN) | 
 | 		set_bit(FLAG_OPEN_DRAIN, &desc->flags); | 
 | 	if (lflags & GPIO_OPEN_SOURCE) | 
 | 		set_bit(FLAG_OPEN_SOURCE, &desc->flags); | 
 |  | 
 | 	/* No particular flag request, return here... */ | 
 | 	if (!(dflags & GPIOD_FLAGS_BIT_DIR_SET)) { | 
 | 		pr_debug("no flags found for %s\n", con_id); | 
 | 		return 0; | 
 | 	} | 
 |  | 
 | 	/* Process flags */ | 
 | 	if (dflags & GPIOD_FLAGS_BIT_DIR_OUT) | 
 | 		status = gpiod_direction_output(desc, | 
 | 				!!(dflags & GPIOD_FLAGS_BIT_DIR_VAL)); | 
 | 	else | 
 | 		status = gpiod_direction_input(desc); | 
 |  | 
 | 	return status; | 
 | } | 
 |  | 
 | /** | 
 |  * gpiod_get_index - obtain a GPIO from a multi-index GPIO function | 
 |  * @dev:	GPIO consumer, can be NULL for system-global GPIOs | 
 |  * @con_id:	function within the GPIO consumer | 
 |  * @idx:	index of the GPIO to obtain in the consumer | 
 |  * @flags:	optional GPIO initialization flags | 
 |  * | 
 |  * This variant of gpiod_get() allows to access GPIOs other than the first | 
 |  * defined one for functions that define several GPIOs. | 
 |  * | 
 |  * Return a valid GPIO descriptor, -ENOENT if no GPIO has been assigned to the | 
 |  * requested function and/or index, or another IS_ERR() code if an error | 
 |  * occurred while trying to acquire the GPIO. | 
 |  */ | 
 | struct gpio_desc *__must_check gpiod_get_index(struct device *dev, | 
 | 					       const char *con_id, | 
 | 					       unsigned int idx, | 
 | 					       enum gpiod_flags flags) | 
 | { | 
 | 	struct gpio_desc *desc = NULL; | 
 | 	int status; | 
 | 	enum gpio_lookup_flags lookupflags = 0; | 
 |  | 
 | 	dev_dbg(dev, "GPIO lookup for consumer %s\n", con_id); | 
 |  | 
 | 	if (dev) { | 
 | 		/* Using device tree? */ | 
 | 		if (IS_ENABLED(CONFIG_OF) && dev->of_node) { | 
 | 			dev_dbg(dev, "using device tree for GPIO lookup\n"); | 
 | 			desc = of_find_gpio(dev, con_id, idx, &lookupflags); | 
 | 		} else if (ACPI_COMPANION(dev)) { | 
 | 			dev_dbg(dev, "using ACPI for GPIO lookup\n"); | 
 | 			desc = acpi_find_gpio(dev, con_id, idx, flags, &lookupflags); | 
 | 		} | 
 | 	} | 
 |  | 
 | 	/* | 
 | 	 * Either we are not using DT or ACPI, or their lookup did not return | 
 | 	 * a result. In that case, use platform lookup as a fallback. | 
 | 	 */ | 
 | 	if (!desc || desc == ERR_PTR(-ENOENT)) { | 
 | 		dev_dbg(dev, "using lookup tables for GPIO lookup\n"); | 
 | 		desc = gpiod_find(dev, con_id, idx, &lookupflags); | 
 | 	} | 
 |  | 
 | 	if (IS_ERR(desc)) { | 
 | 		dev_dbg(dev, "lookup for GPIO %s failed\n", con_id); | 
 | 		return desc; | 
 | 	} | 
 |  | 
 | 	status = gpiod_request(desc, con_id); | 
 | 	if (status < 0) | 
 | 		return ERR_PTR(status); | 
 |  | 
 | 	status = gpiod_configure_flags(desc, con_id, lookupflags, flags); | 
 | 	if (status < 0) { | 
 | 		dev_dbg(dev, "setup of GPIO %s failed\n", con_id); | 
 | 		gpiod_put(desc); | 
 | 		return ERR_PTR(status); | 
 | 	} | 
 |  | 
 | 	return desc; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_get_index); | 
 |  | 
 | /** | 
 |  * fwnode_get_named_gpiod - obtain a GPIO from firmware node | 
 |  * @fwnode:	handle of the firmware node | 
 |  * @propname:	name of the firmware property representing the GPIO | 
 |  * @index:	index of the GPIO to obtain in the consumer | 
 |  * @dflags:	GPIO initialization flags | 
 |  * | 
 |  * This function can be used for drivers that get their configuration | 
 |  * from firmware. | 
 |  * | 
 |  * Function properly finds the corresponding GPIO using whatever is the | 
 |  * underlying firmware interface and then makes sure that the GPIO | 
 |  * descriptor is requested before it is returned to the caller. | 
 |  * | 
 |  * On successfull request the GPIO pin is configured in accordance with | 
 |  * provided @dflags. | 
 |  * | 
 |  * In case of error an ERR_PTR() is returned. | 
 |  */ | 
 | struct gpio_desc *fwnode_get_named_gpiod(struct fwnode_handle *fwnode, | 
 | 					 const char *propname, int index, | 
 | 					 enum gpiod_flags dflags, | 
 | 					 const char *label) | 
 | { | 
 | 	struct gpio_desc *desc = ERR_PTR(-ENODEV); | 
 | 	unsigned long lflags = 0; | 
 | 	bool active_low = false; | 
 | 	bool single_ended = false; | 
 | 	int ret; | 
 |  | 
 | 	if (!fwnode) | 
 | 		return ERR_PTR(-EINVAL); | 
 |  | 
 | 	if (is_of_node(fwnode)) { | 
 | 		enum of_gpio_flags flags; | 
 |  | 
 | 		desc = of_get_named_gpiod_flags(to_of_node(fwnode), propname, | 
 | 						index, &flags); | 
 | 		if (!IS_ERR(desc)) { | 
 | 			active_low = flags & OF_GPIO_ACTIVE_LOW; | 
 | 			single_ended = flags & OF_GPIO_SINGLE_ENDED; | 
 | 		} | 
 | 	} else if (is_acpi_node(fwnode)) { | 
 | 		struct acpi_gpio_info info; | 
 |  | 
 | 		desc = acpi_node_get_gpiod(fwnode, propname, index, &info); | 
 | 		if (!IS_ERR(desc)) | 
 | 			active_low = info.polarity == GPIO_ACTIVE_LOW; | 
 | 	} | 
 |  | 
 | 	if (IS_ERR(desc)) | 
 | 		return desc; | 
 |  | 
 | 	ret = gpiod_request(desc, label); | 
 | 	if (ret) | 
 | 		return ERR_PTR(ret); | 
 |  | 
 | 	if (active_low) | 
 | 		lflags |= GPIO_ACTIVE_LOW; | 
 |  | 
 | 	if (single_ended) { | 
 | 		if (active_low) | 
 | 			lflags |= GPIO_OPEN_DRAIN; | 
 | 		else | 
 | 			lflags |= GPIO_OPEN_SOURCE; | 
 | 	} | 
 |  | 
 | 	ret = gpiod_configure_flags(desc, propname, lflags, dflags); | 
 | 	if (ret < 0) { | 
 | 		gpiod_put(desc); | 
 | 		return ERR_PTR(ret); | 
 | 	} | 
 |  | 
 | 	return desc; | 
 | } | 
 | EXPORT_SYMBOL_GPL(fwnode_get_named_gpiod); | 
 |  | 
 | /** | 
 |  * gpiod_get_index_optional - obtain an optional GPIO from a multi-index GPIO | 
 |  *                            function | 
 |  * @dev: GPIO consumer, can be NULL for system-global GPIOs | 
 |  * @con_id: function within the GPIO consumer | 
 |  * @index: index of the GPIO to obtain in the consumer | 
 |  * @flags: optional GPIO initialization flags | 
 |  * | 
 |  * This is equivalent to gpiod_get_index(), except that when no GPIO with the | 
 |  * specified index was assigned to the requested function it will return NULL. | 
 |  * This is convenient for drivers that need to handle optional GPIOs. | 
 |  */ | 
 | struct gpio_desc *__must_check gpiod_get_index_optional(struct device *dev, | 
 | 							const char *con_id, | 
 | 							unsigned int index, | 
 | 							enum gpiod_flags flags) | 
 | { | 
 | 	struct gpio_desc *desc; | 
 |  | 
 | 	desc = gpiod_get_index(dev, con_id, index, flags); | 
 | 	if (IS_ERR(desc)) { | 
 | 		if (PTR_ERR(desc) == -ENOENT) | 
 | 			return NULL; | 
 | 	} | 
 |  | 
 | 	return desc; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_get_index_optional); | 
 |  | 
 | /** | 
 |  * gpiod_hog - Hog the specified GPIO desc given the provided flags | 
 |  * @desc:	gpio whose value will be assigned | 
 |  * @name:	gpio line name | 
 |  * @lflags:	gpio_lookup_flags - returned from of_find_gpio() or | 
 |  *		of_get_gpio_hog() | 
 |  * @dflags:	gpiod_flags - optional GPIO initialization flags | 
 |  */ | 
 | int gpiod_hog(struct gpio_desc *desc, const char *name, | 
 | 	      unsigned long lflags, enum gpiod_flags dflags) | 
 | { | 
 | 	struct gpio_chip *chip; | 
 | 	struct gpio_desc *local_desc; | 
 | 	int hwnum; | 
 | 	int status; | 
 |  | 
 | 	chip = gpiod_to_chip(desc); | 
 | 	hwnum = gpio_chip_hwgpio(desc); | 
 |  | 
 | 	local_desc = gpiochip_request_own_desc(chip, hwnum, name); | 
 | 	if (IS_ERR(local_desc)) { | 
 | 		status = PTR_ERR(local_desc); | 
 | 		pr_err("requesting hog GPIO %s (chip %s, offset %d) failed, %d\n", | 
 | 		       name, chip->label, hwnum, status); | 
 | 		return status; | 
 | 	} | 
 |  | 
 | 	status = gpiod_configure_flags(desc, name, lflags, dflags); | 
 | 	if (status < 0) { | 
 | 		pr_err("setup of hog GPIO %s (chip %s, offset %d) failed, %d\n", | 
 | 		       name, chip->label, hwnum, status); | 
 | 		gpiochip_free_own_desc(desc); | 
 | 		return status; | 
 | 	} | 
 |  | 
 | 	/* Mark GPIO as hogged so it can be identified and removed later */ | 
 | 	set_bit(FLAG_IS_HOGGED, &desc->flags); | 
 |  | 
 | 	pr_info("GPIO line %d (%s) hogged as %s%s\n", | 
 | 		desc_to_gpio(desc), name, | 
 | 		(dflags&GPIOD_FLAGS_BIT_DIR_OUT) ? "output" : "input", | 
 | 		(dflags&GPIOD_FLAGS_BIT_DIR_OUT) ? | 
 | 		  (dflags&GPIOD_FLAGS_BIT_DIR_VAL) ? "/high" : "/low":""); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | /** | 
 |  * gpiochip_free_hogs - Scan gpio-controller chip and release GPIO hog | 
 |  * @chip:	gpio chip to act on | 
 |  * | 
 |  * This is only used by of_gpiochip_remove to free hogged gpios | 
 |  */ | 
 | static void gpiochip_free_hogs(struct gpio_chip *chip) | 
 | { | 
 | 	int id; | 
 |  | 
 | 	for (id = 0; id < chip->ngpio; id++) { | 
 | 		if (test_bit(FLAG_IS_HOGGED, &chip->gpiodev->descs[id].flags)) | 
 | 			gpiochip_free_own_desc(&chip->gpiodev->descs[id]); | 
 | 	} | 
 | } | 
 |  | 
 | /** | 
 |  * gpiod_get_array - obtain multiple GPIOs from a multi-index GPIO function | 
 |  * @dev:	GPIO consumer, can be NULL for system-global GPIOs | 
 |  * @con_id:	function within the GPIO consumer | 
 |  * @flags:	optional GPIO initialization flags | 
 |  * | 
 |  * This function acquires all the GPIOs defined under a given function. | 
 |  * | 
 |  * Return a struct gpio_descs containing an array of descriptors, -ENOENT if | 
 |  * no GPIO has been assigned to the requested function, or another IS_ERR() | 
 |  * code if an error occurred while trying to acquire the GPIOs. | 
 |  */ | 
 | struct gpio_descs *__must_check gpiod_get_array(struct device *dev, | 
 | 						const char *con_id, | 
 | 						enum gpiod_flags flags) | 
 | { | 
 | 	struct gpio_desc *desc; | 
 | 	struct gpio_descs *descs; | 
 | 	int count; | 
 |  | 
 | 	count = gpiod_count(dev, con_id); | 
 | 	if (count < 0) | 
 | 		return ERR_PTR(count); | 
 |  | 
 | 	descs = kzalloc(sizeof(*descs) + sizeof(descs->desc[0]) * count, | 
 | 			GFP_KERNEL); | 
 | 	if (!descs) | 
 | 		return ERR_PTR(-ENOMEM); | 
 |  | 
 | 	for (descs->ndescs = 0; descs->ndescs < count; ) { | 
 | 		desc = gpiod_get_index(dev, con_id, descs->ndescs, flags); | 
 | 		if (IS_ERR(desc)) { | 
 | 			gpiod_put_array(descs); | 
 | 			return ERR_CAST(desc); | 
 | 		} | 
 | 		descs->desc[descs->ndescs] = desc; | 
 | 		descs->ndescs++; | 
 | 	} | 
 | 	return descs; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_get_array); | 
 |  | 
 | /** | 
 |  * gpiod_get_array_optional - obtain multiple GPIOs from a multi-index GPIO | 
 |  *                            function | 
 |  * @dev:	GPIO consumer, can be NULL for system-global GPIOs | 
 |  * @con_id:	function within the GPIO consumer | 
 |  * @flags:	optional GPIO initialization flags | 
 |  * | 
 |  * This is equivalent to gpiod_get_array(), except that when no GPIO was | 
 |  * assigned to the requested function it will return NULL. | 
 |  */ | 
 | struct gpio_descs *__must_check gpiod_get_array_optional(struct device *dev, | 
 | 							const char *con_id, | 
 | 							enum gpiod_flags flags) | 
 | { | 
 | 	struct gpio_descs *descs; | 
 |  | 
 | 	descs = gpiod_get_array(dev, con_id, flags); | 
 | 	if (IS_ERR(descs) && (PTR_ERR(descs) == -ENOENT)) | 
 | 		return NULL; | 
 |  | 
 | 	return descs; | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_get_array_optional); | 
 |  | 
 | /** | 
 |  * gpiod_put - dispose of a GPIO descriptor | 
 |  * @desc:	GPIO descriptor to dispose of | 
 |  * | 
 |  * No descriptor can be used after gpiod_put() has been called on it. | 
 |  */ | 
 | void gpiod_put(struct gpio_desc *desc) | 
 | { | 
 | 	gpiod_free(desc); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_put); | 
 |  | 
 | /** | 
 |  * gpiod_put_array - dispose of multiple GPIO descriptors | 
 |  * @descs:	struct gpio_descs containing an array of descriptors | 
 |  */ | 
 | void gpiod_put_array(struct gpio_descs *descs) | 
 | { | 
 | 	unsigned int i; | 
 |  | 
 | 	for (i = 0; i < descs->ndescs; i++) | 
 | 		gpiod_put(descs->desc[i]); | 
 |  | 
 | 	kfree(descs); | 
 | } | 
 | EXPORT_SYMBOL_GPL(gpiod_put_array); | 
 |  | 
 | static int __init gpiolib_dev_init(void) | 
 | { | 
 | 	int ret; | 
 |  | 
 | 	/* Register GPIO sysfs bus */ | 
 | 	ret  = bus_register(&gpio_bus_type); | 
 | 	if (ret < 0) { | 
 | 		pr_err("gpiolib: could not register GPIO bus type\n"); | 
 | 		return ret; | 
 | 	} | 
 |  | 
 | 	ret = alloc_chrdev_region(&gpio_devt, 0, GPIO_DEV_MAX, "gpiochip"); | 
 | 	if (ret < 0) { | 
 | 		pr_err("gpiolib: failed to allocate char dev region\n"); | 
 | 		bus_unregister(&gpio_bus_type); | 
 | 	} else { | 
 | 		gpiolib_initialized = true; | 
 | 		gpiochip_setup_devs(); | 
 | 	} | 
 | 	return ret; | 
 | } | 
 | core_initcall(gpiolib_dev_init); | 
 |  | 
 | #ifdef CONFIG_DEBUG_FS | 
 |  | 
 | static void gpiolib_dbg_show(struct seq_file *s, struct gpio_device *gdev) | 
 | { | 
 | 	unsigned		i; | 
 | 	struct gpio_chip	*chip = gdev->chip; | 
 | 	unsigned		gpio = gdev->base; | 
 | 	struct gpio_desc	*gdesc = &gdev->descs[0]; | 
 | 	int			is_out; | 
 | 	int			is_irq; | 
 |  | 
 | 	for (i = 0; i < gdev->ngpio; i++, gpio++, gdesc++) { | 
 | 		if (!test_bit(FLAG_REQUESTED, &gdesc->flags)) { | 
 | 			if (gdesc->name) { | 
 | 				seq_printf(s, " gpio-%-3d (%-20.20s)\n", | 
 | 					   gpio, gdesc->name); | 
 | 			} | 
 | 			continue; | 
 | 		} | 
 |  | 
 | 		gpiod_get_direction(gdesc); | 
 | 		is_out = test_bit(FLAG_IS_OUT, &gdesc->flags); | 
 | 		is_irq = test_bit(FLAG_USED_AS_IRQ, &gdesc->flags); | 
 | 		seq_printf(s, " gpio-%-3d (%-20.20s|%-20.20s) %s %s %s", | 
 | 			gpio, gdesc->name ? gdesc->name : "", gdesc->label, | 
 | 			is_out ? "out" : "in ", | 
 | 			chip->get | 
 | 				? (chip->get(chip, i) ? "hi" : "lo") | 
 | 				: "?  ", | 
 | 			is_irq ? "IRQ" : "   "); | 
 | 		seq_printf(s, "\n"); | 
 | 	} | 
 | } | 
 |  | 
 | static void *gpiolib_seq_start(struct seq_file *s, loff_t *pos) | 
 | { | 
 | 	unsigned long flags; | 
 | 	struct gpio_device *gdev = NULL; | 
 | 	loff_t index = *pos; | 
 |  | 
 | 	s->private = ""; | 
 |  | 
 | 	spin_lock_irqsave(&gpio_lock, flags); | 
 | 	list_for_each_entry(gdev, &gpio_devices, list) | 
 | 		if (index-- == 0) { | 
 | 			spin_unlock_irqrestore(&gpio_lock, flags); | 
 | 			return gdev; | 
 | 		} | 
 | 	spin_unlock_irqrestore(&gpio_lock, flags); | 
 |  | 
 | 	return NULL; | 
 | } | 
 |  | 
 | static void *gpiolib_seq_next(struct seq_file *s, void *v, loff_t *pos) | 
 | { | 
 | 	unsigned long flags; | 
 | 	struct gpio_device *gdev = v; | 
 | 	void *ret = NULL; | 
 |  | 
 | 	spin_lock_irqsave(&gpio_lock, flags); | 
 | 	if (list_is_last(&gdev->list, &gpio_devices)) | 
 | 		ret = NULL; | 
 | 	else | 
 | 		ret = list_entry(gdev->list.next, struct gpio_device, list); | 
 | 	spin_unlock_irqrestore(&gpio_lock, flags); | 
 |  | 
 | 	s->private = "\n"; | 
 | 	++*pos; | 
 |  | 
 | 	return ret; | 
 | } | 
 |  | 
 | static void gpiolib_seq_stop(struct seq_file *s, void *v) | 
 | { | 
 | } | 
 |  | 
 | static int gpiolib_seq_show(struct seq_file *s, void *v) | 
 | { | 
 | 	struct gpio_device *gdev = v; | 
 | 	struct gpio_chip *chip = gdev->chip; | 
 | 	struct device *parent; | 
 |  | 
 | 	if (!chip) { | 
 | 		seq_printf(s, "%s%s: (dangling chip)", (char *)s->private, | 
 | 			   dev_name(&gdev->dev)); | 
 | 		return 0; | 
 | 	} | 
 |  | 
 | 	seq_printf(s, "%s%s: GPIOs %d-%d", (char *)s->private, | 
 | 		   dev_name(&gdev->dev), | 
 | 		   gdev->base, gdev->base + gdev->ngpio - 1); | 
 | 	parent = chip->parent; | 
 | 	if (parent) | 
 | 		seq_printf(s, ", parent: %s/%s", | 
 | 			   parent->bus ? parent->bus->name : "no-bus", | 
 | 			   dev_name(parent)); | 
 | 	if (chip->label) | 
 | 		seq_printf(s, ", %s", chip->label); | 
 | 	if (chip->can_sleep) | 
 | 		seq_printf(s, ", can sleep"); | 
 | 	seq_printf(s, ":\n"); | 
 |  | 
 | 	if (chip->dbg_show) | 
 | 		chip->dbg_show(s, chip); | 
 | 	else | 
 | 		gpiolib_dbg_show(s, gdev); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static const struct seq_operations gpiolib_seq_ops = { | 
 | 	.start = gpiolib_seq_start, | 
 | 	.next = gpiolib_seq_next, | 
 | 	.stop = gpiolib_seq_stop, | 
 | 	.show = gpiolib_seq_show, | 
 | }; | 
 |  | 
 | static int gpiolib_open(struct inode *inode, struct file *file) | 
 | { | 
 | 	return seq_open(file, &gpiolib_seq_ops); | 
 | } | 
 |  | 
 | static const struct file_operations gpiolib_operations = { | 
 | 	.owner		= THIS_MODULE, | 
 | 	.open		= gpiolib_open, | 
 | 	.read		= seq_read, | 
 | 	.llseek		= seq_lseek, | 
 | 	.release	= seq_release, | 
 | }; | 
 |  | 
 | static int __init gpiolib_debugfs_init(void) | 
 | { | 
 | 	/* /sys/kernel/debug/gpio */ | 
 | 	(void) debugfs_create_file("gpio", S_IFREG | S_IRUGO, | 
 | 				NULL, NULL, &gpiolib_operations); | 
 | 	return 0; | 
 | } | 
 | subsys_initcall(gpiolib_debugfs_init); | 
 |  | 
 | #endif	/* DEBUG_FS */ |