| What: /sys/class/power_supply/wireless/device/version |
| Contact: [email protected] |
| Description: |
| Version information about the chip and driver such as chip id, firmware |
| version date and time codes in human readable format |
| |
| What: /sys/class/power_supply/wireless/device/status |
| Contact: [email protected] |
| Description: |
| Driver status and state information printed in human readable format |
| |
| What: /sys/class/power_supply/wireless/device/addr |
| Contact: [email protected] |
| Description: |
| i2c 16-bit register address input to send manual i2c commands |
| |
| What: /sys/class/power_supply/wireless/device/count |
| Contact: [email protected] |
| Description: |
| i2c count input to send manual i2c commands in number of bytes to read/write |
| |
| What: /sys/class/power_supply/wireless/device/data |
| Contact: [email protected] |
| Description: |
| i2c data information to send manual i2c commands in 0xAA 0xBB 0xCC format |
| |
| What: /sys/class/power_supply/wireless/device/ccreset |
| Contact: [email protected] |
| Description: |
| Reset the in-band communication channel between RX and TX |
| |
| What: /sys/class/power_supply/wireless/device/txbusy |
| Contact: [email protected] |
| Description: |
| Check if the in-band communication channel is busy transmitting |
| |
| What: /sys/class/power_supply/wireless/device/txdone |
| Contact: [email protected] |
| Description: |
| Check if the transmission over in-band communication channel is done |
| |
| What: /sys/class/power_supply/wireless/device/txlen |
| Contact: [email protected] |
| Description: |
| Number of bytes to transmit in the in-band communication channel |
| |
| What: /sys/class/power_supply/wireless/device/rxlen |
| Contact: [email protected] |
| Description: |
| Number of bytes received in the in-band communication channel |
| |
| What: /sys/class/power_supply/wireless/device/rxdone |
| Contact: [email protected] |
| Description: |
| Whether the in-band communication channel data receiving is complete |
| |
| What: /sys/class/power_supply/wireless/device/icl_ramp_ua |
| Contact: [email protected] |
| Description: |
| Value to ramp the ICL to during BPP |
| |
| What: /sys/class/power_supply/wireless/device/icl_ramp_delay_ms |
| Contact: [email protected] |
| Description: |
| Amount of time to delay betwenn BPP ICL ramp steps in ms |
| |
| What: /sys/class/power_supply/wireless/device/force_epp |
| Contact: [email protected] |
| Description: |
| Always have the driver act as if the device is in EPP even if it isn't |
| |
| What: /sys/class/power_supply/wireless/device/dc_icl_bpp |
| Contact: [email protected] |
| Description: |
| Set the DC_ICL in BPP mode |
| |
| What: /sys/class/power_supply/wireless/device/dc_icl_epp |
| Contact: [email protected] |
| Description: |
| Set the DC_ICL in EPP mode |
| |
| What: /sys/class/power_supply/wireless/device/alignment |
| Contact: [email protected] |
| Description: |
| Show the alignment status |
| |
| What: /sys/class/power_supply/wireless/device/aicl_delay_ms |
| Contact: [email protected] |
| Description: |
| Legacy interface for setting AICL_DELAY power supply property for QC compat |
| |
| What: /sys/class/power_supply/wireless/device/aicl_icl_ua |
| Contact: [email protected] |
| Description: |
| Legacy interface for setting AICL_ICL power supply property for QC compat |
| |
| What: /sys/class/power_supply/wireless/device/operating_freq |
| Contact: [email protected] |
| Description: |
| Show the current operating frequency of the WLC |
| |
| What: /sys/class/power_supply/wireless/device/ptmc_id |
| Contact: [email protected] |
| Description: |
| Show the TX ID as received through Bidi (proprietary) |
| |
| What: /sys/class/power_supply/wireless/device/ext_ben |
| Contact: [email protected] |
| Description: |
| External boost on or off |
| |
| What: /sys/class/power_supply/wireless/device/qi_vbus_en |
| Contact: [email protected] |
| Description: |
| QI_VBUS_EN gpio on or off |
| |
| What: /sys/class/power_supply/wireless/device/has_wlc_dc |
| Contact: [email protected] |
| Description: |
| Enable or disable HPP feature |
| |
| What: /sys/class/power_supply/wireless/device/gpp_enhanced |
| Contact: [email protected] |
| Description: |
| Enable or disable GPP15W feature |
| |
| What: /sys/class/power_supply/wireless/device/authstart |
| Contact: [email protected] |
| Description: |
| Start WPC Authentication sequence |
| |
| What: /sys/class/power_supply/wireless/device/log_current_filtered |
| Contact: [email protected] |
| Description: |
| Enable printing WLC current continuously into the log |
| |
| What: /sys/class/power_supply/wireless/device/charge_stats |
| Contact: [email protected] |
| Description: |
| Dump out and clear charge stats from the last charging session |
| |
| What: /sys/class/power_supply/wireless/device/fw_rev |
| Contact: [email protected] |
| Description: |
| Saved FW version from the last WLC power on |
| |
| What: /sys/class/power_supply/wireless/device/authtype |
| Contact: [email protected] |
| Description: |
| Authentication type to run (0 = Bidi, others = WPC packet types) |
| |
| What: /sys/class/power_supply/wireless/device/features |
| Contact: [email protected] |
| Description: |
| Supported feature mask in the format "id:features". id=0 corresponds to just set |
| current session |
| |
| What: /sys/class/power_supply/wireless/device/mitigate_threshold |
| Contact: [email protected] |
| Description: |
| SOC threshold at which to trigger dream defend on DL/LL |
| |
| What: /sys/class/power_supply/wireless/device/wpc_ready |
| Contact: [email protected] |
| Description: |
| Check this node to see if the driver/HW is ready for WPC authentication |
| |
| What: /sys/class/power_supply/wireless/device/qien |
| Contact: [email protected] |
| Description: |
| Check/force state of the WLC disable GPIO |
| |
| What: /sys/class/power_supply/wireless/device/align_delta |
| Contact: [email protected] |
| Description: |
| Set the opfreq delta threshold for being considered misaligned |
| |
| What: /sys/class/power_supply/wireless/device/ldo_en |
| Contact: [email protected] |
| Description: |
| Interface for enable/disable external LDO for chips that support it |
| |
| What: /sys/class/power_supply/wireless/device/rtx_sw |
| Contact: [email protected] |
| Description: |
| Change/check the RTX switch status |
| |
| What: /sys/class/power_supply/wireless/device/rtx_boost |
| Contact: [email protected] |
| Description: |
| Turn on the RTX boost to power on the WLC chip. For debug and FW update |
| |
| What: /sys/class/power_supply/wireless/device/rtx |
| Contact: [email protected] |
| Description: |
| Turn on RTX |
| |
| What: /sys/class/power_supply/wireless/device/rtx_status |
| Contact: [email protected] |
| Description: |
| Read the status of RTX |
| |
| What: /sys/class/power_supply/wireless/device/is_rtx_connected |
| Contact: [email protected] |
| Description: |
| Check if RTX is connected |
| |
| What: /sys/class/power_supply/wireless/device/rx_lvl |
| Contact: [email protected] |
| Description: |
| Check the battery level of the device being charged in RTX |
| |
| What: /sys/class/power_supply/wireless/device/rtx_err |
| Contact: [email protected] |
| Description: |
| Read the current RTX error |
| |
| What: /sys/class/power_supply/wireless/device/txdata |
| Contact: [email protected] |
| Description: |
| Set data to be sent over in-band wireless communication |
| |
| What: /sys/class/power_supply/wireless/device/rxdata |
| Contact: [email protected] |
| Description: |
| Read data from in-band wireless communication |
