| // SPDX-License-Identifier: GPL-2.0+ | |
| /* | |
| * Copyright (C) 2006 Freescale Semiconductor, Inc. | |
| * Dave Liu <[email protected]> | |
| * | |
| * Copyright (C) 2007 Logic Product Development, Inc. | |
| * Peter Barada <[email protected]> | |
| * | |
| * Copyright (C) 2007 MontaVista Software, Inc. | |
| * Anton Vorontsov <[email protected]> | |
| * | |
| * (C) Copyright 2008 - 2010 | |
| * Heiko Schocher, DENX Software Engineering, [email protected]. | |
| */ | |
| #include <common.h> | |
| #include <ioports.h> | |
| #include <mpc83xx.h> | |
| #include <i2c.h> | |
| #include <miiphy.h> | |
| #include <asm/io.h> | |
| #include <asm/mmu.h> | |
| #include <asm/processor.h> | |
| #include <pci.h> | |
| #include <linux/libfdt.h> | |
| #include <post.h> | |
| #include "../common/common.h" | |
| DECLARE_GLOBAL_DATA_PTR; | |
| static uchar ivm_content[CONFIG_SYS_IVM_EEPROM_MAX_LEN]; | |
| const qe_iop_conf_t qe_iop_conf_tab[] = { | |
| /* port pin dir open_drain assign */ | |
| #if defined(CONFIG_MPC8360) | |
| /* MDIO */ | |
| {0, 1, 3, 0, 2}, /* MDIO */ | |
| {0, 2, 1, 0, 1}, /* MDC */ | |
| /* UCC4 - UEC */ | |
| {1, 14, 1, 0, 1}, /* TxD0 */ | |
| {1, 15, 1, 0, 1}, /* TxD1 */ | |
| {1, 20, 2, 0, 1}, /* RxD0 */ | |
| {1, 21, 2, 0, 1}, /* RxD1 */ | |
| {1, 18, 1, 0, 1}, /* TX_EN */ | |
| {1, 26, 2, 0, 1}, /* RX_DV */ | |
| {1, 27, 2, 0, 1}, /* RX_ER */ | |
| {1, 24, 2, 0, 1}, /* COL */ | |
| {1, 25, 2, 0, 1}, /* CRS */ | |
| {2, 15, 2, 0, 1}, /* TX_CLK - CLK16 */ | |
| {2, 16, 2, 0, 1}, /* RX_CLK - CLK17 */ | |
| /* DUART - UART2 */ | |
| {5, 0, 1, 0, 2}, /* UART2_SOUT */ | |
| {5, 2, 1, 0, 1}, /* UART2_RTS */ | |
| {5, 3, 2, 0, 2}, /* UART2_SIN */ | |
| {5, 1, 2, 0, 3}, /* UART2_CTS */ | |
| #elif !defined(CONFIG_MPC8309) | |
| /* Local Bus */ | |
| {0, 16, 1, 0, 3}, /* LA00 */ | |
| {0, 17, 1, 0, 3}, /* LA01 */ | |
| {0, 18, 1, 0, 3}, /* LA02 */ | |
| {0, 19, 1, 0, 3}, /* LA03 */ | |
| {0, 20, 1, 0, 3}, /* LA04 */ | |
| {0, 21, 1, 0, 3}, /* LA05 */ | |
| {0, 22, 1, 0, 3}, /* LA06 */ | |
| {0, 23, 1, 0, 3}, /* LA07 */ | |
| {0, 24, 1, 0, 3}, /* LA08 */ | |
| {0, 25, 1, 0, 3}, /* LA09 */ | |
| {0, 26, 1, 0, 3}, /* LA10 */ | |
| {0, 27, 1, 0, 3}, /* LA11 */ | |
| {0, 28, 1, 0, 3}, /* LA12 */ | |
| {0, 29, 1, 0, 3}, /* LA13 */ | |
| {0, 30, 1, 0, 3}, /* LA14 */ | |
| {0, 31, 1, 0, 3}, /* LA15 */ | |
| /* MDIO */ | |
| {3, 4, 3, 0, 2}, /* MDIO */ | |
| {3, 5, 1, 0, 2}, /* MDC */ | |
| /* UCC4 - UEC */ | |
| {1, 18, 1, 0, 1}, /* TxD0 */ | |
| {1, 19, 1, 0, 1}, /* TxD1 */ | |
| {1, 22, 2, 0, 1}, /* RxD0 */ | |
| {1, 23, 2, 0, 1}, /* RxD1 */ | |
| {1, 26, 2, 0, 1}, /* RxER */ | |
| {1, 28, 2, 0, 1}, /* Rx_DV */ | |
| {1, 30, 1, 0, 1}, /* TxEN */ | |
| {1, 31, 2, 0, 1}, /* CRS */ | |
| {3, 10, 2, 0, 3}, /* TxCLK->CLK17 */ | |
| #endif | |
| /* END of table */ | |
| {0, 0, 0, 0, QE_IOP_TAB_END}, | |
| }; | |
| #if defined(CONFIG_SUVD3) | |
| const uint upma_table[] = { | |
| 0x1ffedc00, 0x0ffcdc80, 0x0ffcdc80, 0x0ffcdc04, /* Words 0 to 3 */ | |
| 0x0ffcdc00, 0xffffcc00, 0xffffcc01, 0xfffffc01, /* Words 4 to 7 */ | |
| 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 8 to 11 */ | |
| 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 12 to 15 */ | |
| 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 16 to 19 */ | |
| 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 20 to 23 */ | |
| 0x9cfffc00, 0x00fffc80, 0x00fffc80, 0x00fffc00, /* Words 24 to 27 */ | |
| 0xffffec04, 0xffffec01, 0xfffffc01, 0xfffffc01, /* Words 28 to 31 */ | |
| 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 32 to 35 */ | |
| 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 36 to 39 */ | |
| 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 40 to 43 */ | |
| 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 44 to 47 */ | |
| 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 48 to 51 */ | |
| 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 52 to 55 */ | |
| 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 56 to 59 */ | |
| 0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01 /* Words 60 to 63 */ | |
| }; | |
| #endif | |
| static int piggy_present(void) | |
| { | |
| struct km_bec_fpga __iomem *base = | |
| (struct km_bec_fpga __iomem *)CONFIG_SYS_KMBEC_FPGA_BASE; | |
| return in_8(&base->bprth) & PIGGY_PRESENT; | |
| } | |
| #if defined(CONFIG_KMVECT1) | |
| int ethernet_present(void) | |
| { | |
| /* ethernet port connected to simple switch without piggy */ | |
| return 1; | |
| } | |
| #else | |
| int ethernet_present(void) | |
| { | |
| return piggy_present(); | |
| } | |
| #endif | |
| int board_early_init_r(void) | |
| { | |
| struct km_bec_fpga *base = | |
| (struct km_bec_fpga *)CONFIG_SYS_KMBEC_FPGA_BASE; | |
| #if defined(CONFIG_SUVD3) | |
| immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; | |
| fsl_lbc_t *lbc = &immap->im_lbc; | |
| u32 *mxmr = &lbc->mamr; | |
| #endif | |
| #if defined(CONFIG_MPC8360) | |
| unsigned short svid; | |
| /* | |
| * Because of errata in the UCCs, we have to write to the reserved | |
| * registers to slow the clocks down. | |
| */ | |
| svid = SVR_REV(mfspr(SVR)); | |
| switch (svid) { | |
| case 0x0020: | |
| /* | |
| * MPC8360ECE.pdf QE_ENET10 table 4: | |
| * IMMR + 0x14A8[4:5] = 11 (clk delay for UCC 2) | |
| * IMMR + 0x14A8[18:19] = 11 (clk delay for UCC 1) | |
| */ | |
| setbits_be32((void *)(CONFIG_SYS_IMMR + 0x14a8), 0x0c003000); | |
| break; | |
| case 0x0021: | |
| /* | |
| * MPC8360ECE.pdf QE_ENET10 table 4: | |
| * IMMR + 0x14AC[24:27] = 1010 | |
| */ | |
| clrsetbits_be32((void *)(CONFIG_SYS_IMMR + 0x14ac), | |
| 0x00000050, 0x000000a0); | |
| break; | |
| } | |
| #endif | |
| /* enable the PHY on the PIGGY */ | |
| setbits_8(&base->pgy_eth, 0x01); | |
| /* enable the Unit LED (green) */ | |
| setbits_8(&base->oprth, WRL_BOOT); | |
| /* enable Application Buffer */ | |
| setbits_8(&base->oprtl, OPRTL_XBUFENA); | |
| #if defined(CONFIG_SUVD3) | |
| /* configure UPMA for APP1 */ | |
| upmconfig(UPMA, (uint *) upma_table, | |
| sizeof(upma_table) / sizeof(uint)); | |
| out_be32(mxmr, CONFIG_SYS_MAMR); | |
| #endif | |
| return 0; | |
| } | |
| int misc_init_r(void) | |
| { | |
| ivm_read_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN); | |
| return 0; | |
| } | |
| #if defined(CONFIG_KMVECT1) | |
| #include <mv88e6352.h> | |
| /* Marvell MV88E6122 switch configuration */ | |
| static struct mv88e_sw_reg extsw_conf[] = { | |
| /* port 1, FRONT_MDI, autoneg */ | |
| { PORT(1), PORT_PHY, NO_SPEED_FOR }, | |
| { PORT(1), PORT_CTRL, FORWARDING | EGRS_FLD_ALL }, | |
| { PHY(1), PHY_1000_CTRL, NO_ADV }, | |
| { PHY(1), PHY_SPEC_CTRL, AUTO_MDIX_EN }, | |
| { PHY(1), PHY_CTRL, PHY_100_MBPS | AUTONEG_EN | AUTONEG_RST | | |
| FULL_DUPLEX }, | |
| /* port 2, unused */ | |
| { PORT(2), PORT_CTRL, PORT_DIS }, | |
| { PHY(2), PHY_CTRL, PHY_PWR_DOWN }, | |
| { PHY(2), PHY_SPEC_CTRL, SPEC_PWR_DOWN }, | |
| /* port 3, BP_MII (CPU), PHY mode, 100BASE */ | |
| { PORT(3), PORT_CTRL, FORWARDING | EGRS_FLD_ALL }, | |
| /* port 4, ESTAR to slot 11, SerDes, 1000BASE-X */ | |
| { PORT(4), PORT_STATUS, NO_PHY_DETECT }, | |
| { PORT(4), PORT_PHY, SPEED_1000_FOR }, | |
| { PORT(4), PORT_CTRL, FORWARDING | EGRS_FLD_ALL }, | |
| /* port 5, ESTAR to slot 13, SerDes, 1000BASE-X */ | |
| { PORT(5), PORT_STATUS, NO_PHY_DETECT }, | |
| { PORT(5), PORT_PHY, SPEED_1000_FOR }, | |
| { PORT(5), PORT_CTRL, FORWARDING | EGRS_FLD_ALL }, | |
| /* | |
| * Errata Fix: 1.9V Output from Internal 1.8V Regulator, | |
| * acc . MV-S300889-00D.pdf , clause 4.5 | |
| */ | |
| { PORT(5), 0x1A, 0xADB1 }, | |
| /* port 6, unused, this port has no phy */ | |
| { PORT(6), PORT_CTRL, PORT_DIS }, | |
| /* | |
| * Errata Fix: 1.9V Output from Internal 1.8V Regulator, | |
| * acc . MV-S300889-00D.pdf , clause 4.5 | |
| */ | |
| { PORT(5), 0x1A, 0xADB1 }, | |
| }; | |
| #endif | |
| int last_stage_init(void) | |
| { | |
| #if defined(CONFIG_KMVECT1) | |
| struct km_bec_fpga __iomem *base = | |
| (struct km_bec_fpga __iomem *)CONFIG_SYS_KMBEC_FPGA_BASE; | |
| u8 tmp_reg; | |
| /* Release mv88e6122 from reset */ | |
| tmp_reg = in_8(&base->res1[0]) | 0x10; /* DIRECT3 register */ | |
| out_8(&base->res1[0], tmp_reg); /* GP28 as output */ | |
| tmp_reg = in_8(&base->gprt3) | 0x10; /* GP28 to high */ | |
| out_8(&base->gprt3, tmp_reg); | |
| /* configure MV88E6122 switch */ | |
| char *name = "UEC2"; | |
| if (miiphy_set_current_dev(name)) | |
| return 0; | |
| mv88e_sw_program(name, CONFIG_KM_MVEXTSW_ADDR, extsw_conf, | |
| ARRAY_SIZE(extsw_conf)); | |
| mv88e_sw_reset(name, CONFIG_KM_MVEXTSW_ADDR); | |
| if (piggy_present()) { | |
| env_set("ethact", "UEC2"); | |
| env_set("netdev", "eth1"); | |
| puts("using PIGGY for network boot\n"); | |
| } else { | |
| env_set("netdev", "eth0"); | |
| puts("using frontport for network boot\n"); | |
| } | |
| #endif | |
| #if defined(CONFIG_KMCOGE5NE) | |
| struct bfticu_iomap *base = | |
| (struct bfticu_iomap *)CONFIG_SYS_BFTIC3_BASE; | |
| u8 dip_switch = in_8((u8 *)&(base->mswitch)) & BFTICU_DIPSWITCH_MASK; | |
| if (dip_switch != 0) { | |
| /* start bootloader */ | |
| puts("DIP: Enabled\n"); | |
| env_set("actual_bank", "0"); | |
| } | |
| #endif | |
| set_km_env(); | |
| return 0; | |
| } | |
| static int fixed_sdram(void) | |
| { | |
| immap_t *im = (immap_t *)CONFIG_SYS_IMMR; | |
| u32 msize = 0; | |
| u32 ddr_size; | |
| u32 ddr_size_log2; | |
| out_be32(&im->sysconf.ddrlaw[0].ar, (LAWAR_EN | 0x1e)); | |
| out_be32(&im->ddr.csbnds[0].csbnds, (CONFIG_SYS_DDR_CS0_BNDS) | 0x7f); | |
| out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG); | |
| out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0); | |
| out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1); | |
| out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2); | |
| out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3); | |
| out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG); | |
| out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2); | |
| out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE); | |
| out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2); | |
| out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL); | |
| out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CNTL); | |
| udelay(200); | |
| setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN); | |
| msize = CONFIG_SYS_DDR_SIZE << 20; | |
| disable_addr_trans(); | |
| msize = get_ram_size(CONFIG_SYS_DDR_BASE, msize); | |
| enable_addr_trans(); | |
| msize /= (1024 * 1024); | |
| if (CONFIG_SYS_DDR_SIZE != msize) { | |
| for (ddr_size = msize << 20, ddr_size_log2 = 0; | |
| (ddr_size > 1); | |
| ddr_size = ddr_size >> 1, ddr_size_log2++) | |
| if (ddr_size & 1) | |
| return -1; | |
| out_be32(&im->sysconf.ddrlaw[0].ar, | |
| (LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE))); | |
| out_be32(&im->ddr.csbnds[0].csbnds, | |
| (((msize / 16) - 1) & 0xff)); | |
| } | |
| return msize; | |
| } | |
| int dram_init(void) | |
| { | |
| immap_t *im = (immap_t *)CONFIG_SYS_IMMR; | |
| u32 msize = 0; | |
| if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im) | |
| return -ENXIO; | |
| out_be32(&im->sysconf.ddrlaw[0].bar, | |
| CONFIG_SYS_DDR_BASE & LAWBAR_BAR); | |
| msize = fixed_sdram(); | |
| #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) | |
| /* | |
| * Initialize DDR ECC byte | |
| */ | |
| ddr_enable_ecc(msize * 1024 * 1024); | |
| #endif | |
| /* return total bus SDRAM size(bytes) -- DDR */ | |
| gd->ram_size = msize * 1024 * 1024; | |
| return 0; | |
| } | |
| int checkboard(void) | |
| { | |
| puts("Board: Keymile " CONFIG_KM_BOARD_NAME); | |
| if (piggy_present()) | |
| puts(" with PIGGY."); | |
| puts("\n"); | |
| return 0; | |
| } | |
| int ft_board_setup(void *blob, bd_t *bd) | |
| { | |
| ft_cpu_setup(blob, bd); | |
| return 0; | |
| } | |
| #if defined(CONFIG_HUSH_INIT_VAR) | |
| int hush_init_var(void) | |
| { | |
| ivm_analyze_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN); | |
| return 0; | |
| } | |
| #endif | |
| #if defined(CONFIG_POST) | |
| int post_hotkeys_pressed(void) | |
| { | |
| int testpin = 0; | |
| struct km_bec_fpga *base = | |
| (struct km_bec_fpga *)CONFIG_SYS_KMBEC_FPGA_BASE; | |
| int testpin_reg = in_8(&base->CONFIG_TESTPIN_REG); | |
| testpin = (testpin_reg & CONFIG_TESTPIN_MASK) != 0; | |
| debug("post_hotkeys_pressed: %d\n", !testpin); | |
| return testpin; | |
| } | |
| ulong post_word_load(void) | |
| { | |
| void* addr = (ulong *) (CPM_POST_WORD_ADDR); | |
| debug("post_word_load 0x%08lX: 0x%08X\n", (ulong)addr, in_le32(addr)); | |
| return in_le32(addr); | |
| } | |
| void post_word_store(ulong value) | |
| { | |
| void* addr = (ulong *) (CPM_POST_WORD_ADDR); | |
| debug("post_word_store 0x%08lX: 0x%08lX\n", (ulong)addr, value); | |
| out_le32(addr, value); | |
| } | |
| int arch_memory_test_prepare(u32 *vstart, u32 *size, phys_addr_t *phys_offset) | |
| { | |
| *vstart = CONFIG_SYS_MEMTEST_START; | |
| *size = CONFIG_SYS_MEMTEST_END - CONFIG_SYS_MEMTEST_START; | |
| debug("arch_memory_test_prepare 0x%08X 0x%08X\n", *vstart, *size); | |
| return 0; | |
| } | |
| #endif |