| // SPDX-License-Identifier: GPL-2.0+ | |
| /* | |
| * (C) Copyright 2003 | |
| * [email protected] | |
| */ | |
| #include <common.h> | |
| #include <command.h> | |
| #include <mach/au1x00.h> | |
| #include <asm/mipsregs.h> | |
| #include <asm/io.h> | |
| DECLARE_GLOBAL_DATA_PTR; | |
| int dram_init(void) | |
| { | |
| /* Sdram is setup by assembler code */ | |
| /* If memory could be changed, we should return the true value here */ | |
| gd->ram_size = 64 * 1024 * 1024; | |
| return 0; | |
| } | |
| #define BCSR_PCMCIA_PC0DRVEN 0x0010 | |
| #define BCSR_PCMCIA_PC0RST 0x0080 | |
| /* In arch/mips/cpu/cpu.c */ | |
| void write_one_tlb( int index, u32 pagemask, u32 hi, u32 low0, u32 low1 ); | |
| int checkboard (void) | |
| { | |
| #if defined(CONFIG_IDE_PCMCIA) && 0 | |
| u16 status; | |
| #endif | |
| /* volatile u32 *pcmcia_bcsr = (u32*)(DB1000_BCSR_ADDR+0x10); */ | |
| volatile u32 *sys_counter = (volatile u32*)SYS_COUNTER_CNTRL; | |
| u32 proc_id; | |
| *sys_counter = 0x100; /* Enable 32 kHz oscillator for RTC/TOY */ | |
| proc_id = read_c0_prid(); | |
| switch (proc_id >> 24) { | |
| case 0: | |
| puts ("Board: Pb1000\n"); | |
| printf ("CPU: Au1000 396 MHz, id: 0x%02x, rev: 0x%02x\n", | |
| (proc_id >> 8) & 0xFF, proc_id & 0xFF); | |
| break; | |
| case 1: | |
| puts ("Board: Pb1500\n"); | |
| printf ("CPU: Au1500, id: 0x%02x, rev: 0x%02x\n", | |
| (proc_id >> 8) & 0xFF, proc_id & 0xFF); | |
| break; | |
| case 2: | |
| puts ("Board: Pb1100\n"); | |
| printf ("CPU: Au1100, id: 0x%02x, rev: 0x%02x\n", | |
| (proc_id >> 8) & 0xFF, proc_id & 0xFF); | |
| break; | |
| default: | |
| printf ("Unsupported cpu %d, proc_id=0x%x\n", proc_id >> 24, proc_id); | |
| } | |
| set_io_port_base(0); | |
| #if defined(CONFIG_IDE_PCMCIA) && 0 | |
| /* Enable 3.3 V on slot 0 ( VCC ) | |
| No 5V */ | |
| status = 4; | |
| *pcmcia_bcsr = status; | |
| status |= BCSR_PCMCIA_PC0DRVEN; | |
| *pcmcia_bcsr = status; | |
| au_sync(); | |
| udelay(300*1000); | |
| status |= BCSR_PCMCIA_PC0RST; | |
| *pcmcia_bcsr = status; | |
| au_sync(); | |
| udelay(100*1000); | |
| /* PCMCIA is on a 36 bit physical address. | |
| We need to map it into a 32 bit addresses */ | |
| #if 0 | |
| /* We dont need theese unless we run whole pcmcia package */ | |
| write_one_tlb(20, /* index */ | |
| 0x01ffe000, /* Pagemask, 16 MB pages */ | |
| CONFIG_SYS_PCMCIA_IO_BASE, /* Hi */ | |
| 0x3C000017, /* Lo0 */ | |
| 0x3C200017); /* Lo1 */ | |
| write_one_tlb(21, /* index */ | |
| 0x01ffe000, /* Pagemask, 16 MB pages */ | |
| CONFIG_SYS_PCMCIA_ATTR_BASE, /* Hi */ | |
| 0x3D000017, /* Lo0 */ | |
| 0x3D200017); /* Lo1 */ | |
| #endif /* 0 */ | |
| write_one_tlb(22, /* index */ | |
| 0x01ffe000, /* Pagemask, 16 MB pages */ | |
| CONFIG_SYS_PCMCIA_MEM_ADDR, /* Hi */ | |
| 0x3E000017, /* Lo0 */ | |
| 0x3E200017); /* Lo1 */ | |
| #endif /* CONFIG_IDE_PCMCIA */ | |
| return 0; | |
| } |