docs/html/tv/adt-1/regulatory.jd

page.title=Regulatory Disclosures for ADT-1
fullpage=1
nonavpage=true

@jd:body

<div class="wrap" style="width:940px;">

<h1>Regulatory Disclosures for ADT-1</h1>

<p>Disclosures for the <a href="index.html">ADT-1</a> device.</p>

<p>
  Model: W2<br>
  FCC ID: A4R-W2<br>
  IC: 10395A-W2
</p>

<p>U.S. Federal Communications Commission Notices</p>
<p>To satisfy FCC and IC exposure requirements, a separation distance of at least 20 cm should
  be maintained between the antenna of this device and persons during device operation. Operations
  at closer than this distance are not recommended.</p>
<p>The antenna used for this transmitter must not be co-located in conjunction with any other
  antenna or transmitter.</p>
<p>This equipment has been tested and found to comply with the limits for a Class B digital
  device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
  protection against harmful interference in a residential installation. This equipment generates,
  uses and can radiate radio frequency energy and, if not installed and used in accordance with the
  instructions, may cause harmful interference to radio communications. However, there is no
  guarantee that interference will not occur in a particular installation. If this equipment does
  cause harmful interference to radio or television reception, which can be determined by turning
  the equipment off and on, the user is encouraged to try to correct the interference by one or more
  of the following measures:</p>
<p>—Reorient or relocate the receiving antenna.</p>
<p>—Increase the separation between the equipment and receiver.</p>
<p>—Connect the equipment into an outlet on a circuit different from that to which the receiver
  is connected.</p>
<p>—Consult the dealer or an experienced radio/ TV technician for help.</p>
<p>This device complies with part 15 of the FCC Rules. Operation is subject to the following two
  conditions: (1) This device may not cause harmful interference, and (2) this device must accept
  any interference received, including interference that may cause undesired operation.</p>
<p>Changes or modifications not expressly approved by Google Inc. could void the user's
  authority to operate the equipment.</p>
<p>Industry Canada Notices</p>
<p>This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
  subject to the following two conditions: (1) this device may not cause interference, and (2) this
  device must accept any interference, including interference that may cause undesired operation of
  the device.</p>
<p>Under Industry Canada regulations, this radio transmitter may only operate using an antenna
  of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
  potential radio interference to other users, the antenna type and its gain should be so chosen
  that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
  successful communication.</p>
<p>The radiated output power of the Wireless Device is below the Industry Canada (IC) radio
  frequency exposure limits. The Wireless Device should be used in such a manner such that the
  potential for human contact during normal operation is minimized.</p>

<hr />

<p>CAN ICES-3 (B)/NMB-3(B)</p>
<p>
  <u>Avis d’<em>Industrie Canada</em></u>
</p>
<p>
  Le présent appareil est conforme aux <em>CNR</em> d'Industrie Canada applicables aux appareils
  radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
  l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage
  radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
</p>
<p>
  En vertu de la règlementation d’<em>Industrie Canada</em>, cet émetteur radio peut
    fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
    l'émetteur par <em>Industrie Canada</em>. Dans le but de réduire les risques de brouillage
  radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son
  gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
  nécessaire à l'établissement d'une communication satisfaisante.
</p>
<p>
  La puissance rayonnée en sortie de l'appareil sans fil est inférieure aux limites fixées par
  <em>Industrie Canada</em> en matière d'exposition aux radiofréquences. L'appareil sans fil
  doit être utilisé de sorte que la possibilité d'un contact humain pendant le fonctionnement
  normal soit limitée.
</p>

</div> <!-- end.class.wrap -->

<div class="layout-content-col col-16" style="padding-top:1px">
  <!-- layout div, so auto-gen footer sits correctly; do not remove -->
</div>